Home › Engine / Hybrid System · 2UZ-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0340    Camshaft Position Sensor Circuit Malfunction

DTC    P0345    Camshaft Position Sensor "A" Circuit (Bank 2)

for Preparation Click here


DESCRIPTION

The Variable Valve Timing (VVT) sensor consists of a magnet, iron core and pickup coil. The VVT signal plate has 3 teeth on its outer circumference and is installed on the camshaft timing pulley. When the camshafts rotates, changes occur on the camshaft protrusions and the pickup coil air gaps. These changes cause fluctuations in the magnetic field and generate voltage in the pickup coil.
Each sensor monitors its timing rotor, which is located on the camshaft. The ECM uses the sensor to detect the camshaft angle. The camshaft rotation synchronizes with the crankshaft rotation, and this sensor communicates the rotation of the camshaft timing rotor as a pulse signal to the ECM. Based on the signal, the ECM controls camshaft position.
The crankshaft angle sensor plate has 34 teeth. The pickup coil generates 34 signals for each engine revolution. Based on a combination of the VVT signal and NE signal, the ECM detects the crankshaft angle. Then the ECM uses this data to control fuel injection time and injection timing. Also, based on the NE signal, the ECM detects the engine speed.

DTC No.
DTC Detection Condition
Trouble Area
P0340
P0345
When either condition below is met:
  1. No VVT sensor signal to ECM during cranking
    (2 trip detection logic)
  2. No VVT sensor signal to ECM with engine speed 600 rpm or more
    (1 trip detection logic)
  1. Open or short in VVT sensor circuit
  2. VVT sensor
  3. Camshaft timing gear for intake camshaft
  4. Timing belt has a jumped tooth
  5. ECM

  1. A164292E02
    Reference: Inspection using an oscilloscope

    HINT:
    1. The correct waveform is as shown.
    2. VV1+ and VV2+ stand for the VVT sensor signal, and NE+ stands for the CKP sensor signal.

    Item
    Content
    Terminal
    NE+ - NE-
    VV1+ - VV1-
    VV2+ - VV2-
    Equipment Setting
    2 V/DIV.
    20 msec./DIV.
    Condition
    Cranking or idling

MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the engine revolving, the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY


Related DTCs
P0340: VVT sensor (for bank 1) open/short
P0340: VVT position/Crankshaft position misalignment (for bank 1)
P0345: VVT sensor (for bank 2) open/short
P0345: VVT position/Crankshaft position misalignment (for bank 2)
Required Sensors/Components (Main)
VVT position sensor (for bank 1 and 2)
Required Sensors/Components (Sub)
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
5 seconds (case 1)
4 seconds (case 2)
MIL Operation
Immediate (case 1)
2 driving cycles (case 2)
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever following DTCs are not present
None

Case 1 
Engine speed
600 rpm or more
Battery voltage
8 V or more
Starter
OFF
Ignition switch
ON

Case 2 
Starter
ON
Minimum battery voltage
Less than 11 V

TYPICAL MALFUNCTION THRESHOLDS


VVT sensor signal
No signal

COMPONENT OPERATING RANGE


VVT sensor voltage
  1. VVT sensor output voltage fluctuates while camshaft revolving.
  2. 3 VVT sensor signals per 2 crankshaft revolutions.

WIRING DIAGRAM

Refer to DTC P0335 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).

1.INSPECT VVT SENSOR (RESISTANCE)


    A160402E02
  1. Disconnect the VVT sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Cold
    835 to 1400 Ω
    1 - 2
    Hot
    1060 to 1645 Ω

    HINT:
    In the above chart, the terms "cold" and "hot" refer to the temperature of the sensor.
    "Cold" means approximately -10 to 50°C (14 to 122°F).
    "Hot" means approximately 50 to 100°C (122 to 212°F).



NG
REPLACE VVT SENSOR (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)


    A164728E03
  1. Disconnect the VVT sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D68-1 - D56-92 (VV1+)
    Always
    Below 1 Ω
    D68-2 - D56-91 (VV1-)
    Always
    Below 1 Ω
    D69-1 - D56-87 (VV2+)
    Always
    Below 1 Ω
    D69-2 - D56-88 (VV2-)
    Always
    Below 1 Ω
    D68-1 or D56-92 (VV1+) - Body ground
    Always
    10 kΩ or higher
    D68-2 or D56-91 (VV1-) - Body ground
    Always
    10 kΩ or higher
    D69-1 or D56-87 (VV2+) - Body ground
    Always
    10 kΩ or higher
    D69-2 or D56-88 (VV2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK SENSOR INSTALLATION (VVT SENSOR)


    BR03795E17
  1. Check the VVT sensor installation.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


4.INSPECT CAMSHAFT (TEETH)
  1. Remove the cylinder head cover (Click here).

  1. Check the teeth of the camshaft.

    OK:
    The camshaft does not have any cracks or deformation.



NG
REPLACE CAMSHAFT (Click here)
OK


5.REPLACE VVT SENSOR
  1. Replace the VVT sensor (Click here).


NEXT


6.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream ON.

  1. Clear DTCs.

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    No DTC is output
    A
    P0340 or P0345 is output
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END