SFI SYSTEM > VC Output Circuit |


| 1.CHECK MIL |
Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.
|
| ||||
| OK | ||
| ||
| 2.CHECK COMMUNICATION BETWEEN TECHSTREAM AND ECM |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream ON.
Check the communication between the Techstream and ECM.
| Result | Proceed to |
| Communication is not possible | A |
| Communication is possible | B |
|
| ||||
| A | |
| 3.CHECK MIL (THROTTLE POSITION SENSOR) |
Disconnect the throttle body connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL does not illuminate | A |
| MIL illuminates | B |
|
| ||||
| A | |
| 4.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR) |
Disconnect the accelerator pedal position sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL does not illuminate | A |
| MIL illuminates | B |
|
| ||||
| A | |
| 5.CHECK MIL (CANISTER PUMP MODULE) |
![]() |
Disconnect the canister pump module connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL does not illuminate | A |
| MIL illuminates | B |
|
| ||||
| A | |
| 6.CHECK MIL (AIR SWITCHING VALVE for Bank 1) |
Disconnect the air switching valve connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL does not illuminate | A |
| MIL illuminates | B |
|
| ||||
| A | |
| 7.CHECK MIL (AIR SWITCHING VALVE for Bank 2) |
Disconnect the air switching valve connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL does not illuminate | A |
| MIL illuminates | B |
|
| ||||
| A | |
| 8.CHECK MIL (POWER STEERING OIL PRESSURE SENSOR) |
Disconnect the power steering oil pressure sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL does not illuminate | A |
| MIL illuminates | B |
|
| ||||
| A | |
| 9.CHECK MIL (CAMSHAFT POSITION SENSOR) |
Disconnect the camshaft position sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL does not illuminate | A |
| MIL illuminates | B |
|
| ||||
| A | |
| 10.CHECK HARNESS AND CONNECTOR |
Disconnect the throttle body connector.
Disconnect the accelerator pedal position sensor connector.
Disconnect the canister pump module connector.
Disconnect the air switching valve connector.
Disconnect the air switching valve connector.
Disconnect the power steering oil pressure sensor connector.
Disconnect the camshaft position sensor connector.
![]() |
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D56-80 (VCTA) - Body ground | Always | 10 kΩ or higher |
| A27-57 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A27-59 (VCP2) - Body ground | Always | 10 kΩ or higher |
| D56-66 (VC) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||