DTC C1231/31 Steering Angle Sensor Circuit Malfunction |
| DTC Code | DTC Detection Condition | Trouble Area |
| C1231/31 | When any of following conditions detected:
|
|

| 1.PERFORM INITIALIZATION OF STEERING ANGLE SENSOR |
Check that the steering wheel is in the centered position.
Disconnect the negative battery terminal for more than 2 seconds.
Reconnect the negative battery terminal.
After driving the vehicle straight ahead at 15 km/h (9.3 mph) or more for a few seconds, drive the vehicle at a speed of 45 km/h (28 mph) or more and turn the steering wheel to the right and left for several seconds.
| NEXT | |
| 2.READ VALUE USING TECHSTREAM (STEERING ANGLE SENSOR) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream ON.
Check that the steering wheel is centered.
Select the Data List mode on the Techstream.
Techstream
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Steering Angle Sensor | Steering angle sensor / min.: -3276.8 deg, max.: 3276.7 deg | Left turn: Increase Right turn: Decrease | - |
| Steering Angle Value | Steering angle value / min.: -3276.8 deg, max.: 3276.7 deg | Min.: -3276.8 deg Max.: 3276.7 deg | - |
Check that the steering wheel turning angle of the steering angle sensor changes when turning the steering wheel.
|
| ||||
| OK | |
| 3.RECONFIRM DTC |
Clear the DTC (Click here).
Start the engine.
After driving the vehicle straight ahead at 15 km/h (9.3 mph) or more for a few seconds, drive the vehicle at a speed of 45 km/h (28 mph) or more and turn the steering wheel to the right and left for several seconds.
Check if the same DTC is recorded (Click here).
| Result | Proceed to |
| DTC is output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||
| 4.CHECK CAN COMMUNICATION SYSTEM |
Check if the CAN communication system DTC is output (Click here).
| Result | Proceed to |
| DTC is not output | A |
| DTC is output | B |
|
| ||||
| A | |
| 5.CHECK STEERING ANGLE SENSOR |
Check that the steering angle sensor has been installed correctly (Click here).
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR - BATTERY AND BODY GROUND) |
![]() |
Remove the steering wheel and the column cover lower.
Disconnect the steering angle sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| H6-1(IG) - Body ground | Ignition switch ON | 11 to 14 V |
| H6-3 (BAT) - Body ground | Always |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H6-2 (ESS) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 7.REPLACE STEERING ANGLE SENSOR |
Replace the steering angle sensor (Click here).
| NEXT | |
| 8.RECONFIRM DTC |
Clear the DTC (Click here).
Start the engine.
Drive the vehicle at a speed of 45 km/h (28 mph) or more and turn the steering wheel to the right and left for several seconds.
Check if the same DTC is recorded (Click here).
| Result | Proceed to |
| DTC is output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||