Home › Vehicle Exterior › WINDOW / GLASS › WINDOW DEFOGGER SYSTEM

WINDOW DEFOGGER SYSTEM > Rear Window Defogger System does not Operate

for Preparation Click here


DESCRIPTION

When the defogger switch in the integration control and panel is turned on, the air conditioning amplifier checks that the back door window is in the fully closed position, turns on the DEFOG relay, and then activates the rear window defogger.

HINT:
  1. The rear window defogger and rear wiper will not operate if the back door power window is not initialized.
  2. The back door window fully closed position signal is transmitted from the back door ECU to the main body ECU via LIN communication, and from the main body ECU to the air conditioning amplifier via CAN communication.


WIRING DIAGRAM


B191461E03


INSPECTION PROCEDURE

1.PERFORM INITIALIZATION (BACK DOOR POWER WINDOW)
  1. Initialize the back door power window regulator motor (Click here)

  1. Check if rear window defogger function operate (Click here)

    OK:
    Rear window defogger function operates.



NG
Go to step 2
OK

END 

2.CHECK LIN COMMUNICATION SYSTEM
  1. Check for LIN communication system DTCs related to the power window control system (Click here).

    OK:
    LIN communication system DTCs are not output.



NG
GO TO LIN COMMUNICATION SYSTEM (Click here)
OK


3.CHECK CAN COMMUNICATION SYSTEM
  1. Check for CAN communication system DTCs (Click here).

    OK:
    CAN communication system DTCs are not output.



NG
GO TO CAN COMMUNICATION SYSTEM (Click here)
OK


4.PERFORM ACTIVE TEST USING TECHSTREAM (DEFOG RELAY)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Air Conditioner / Active Test / Defogger Relay (Rear)

  1. Check that the defogger operation.

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Defogger Relay (Rear)
    Rear window defogger relay operation
    OFF or ON
    -

    OK:
    Defogger operates on and off.



NG
Go to step 8
OK


5.CHECK AIR CONDITIONING SYSTEM (LIN COMMUNICATION)
  1. Operate the front air conditioner control panel to change the set temperature and check that the temperature at the outlets changes.

    OK:
    The outlet temperature changes in accordance with the operation of the control panel.



NG
GO TO AIR CONDITIONING CONTROL CIRCUIT (Click here)
OK


6.REPLACE INTEGRATION CONTROL AND PANEL
  1. Temporarily replace the integration control and panel with a new or normally functioning one (Click here).


NEXT


7.CHECK INTEGRATION CONTROL AND PANEL (OPERATION)
  1. Check that the malfunction disappears.

    OK:
    Malfunction disappears.



NG
REPLACE AIR CONDITIONING AMPLIFIER (Click here)
OK

END (INTEGRATION CONTROL AND PANEL IS DEFECTIVE) 

8.CHECK HARNESS AND CONNECTOR (DEFOG RELAY - BACK DOOR GLASS [REAR WINDOW DEFOGGER])


    B191463E03
  1. Disconnect the V11 rear defogger connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    V11-1(B) - Body ground
    Engine running
    Rear defogger switch ON
    11 to 14 V

  1. Reconnect the rear defogger connector.



NG
Go to step 10
OK


9.CHECK HARNESS AND CONNECTOR (REAR WINDOW DEFOGGER - BODY GROUND)


    B191463E06
  1. Disconnect the V12 rear defogger connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    V12-1(E) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the rear defogger connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE BACK DOOR GLASS (REAR WINDOW DEFOGGER) (Click here)  

10.INSPECT FUSE (DEFOG)


    B191460E03
  1. Remove the DEFOG fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    DEFOG fuse
    Always
    Below 1 Ω

  1. Reinstall the DEFOG fuse.



NG
REPLACE FUSE
OK


11.INSPECT DEFOG RELAY


    B106753E01
  1. Remove the DEFOG relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    When battery voltage is not applied between terminals 1 and 2
    Below 1 Ω
    3 - 5
    10 kΩ or higher
    3 - 4
    When battery voltage is applied to terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Below 1 Ω

  1. Reinstall the DEFOG relay.



NG
REPLACE DEFOG RELAY
OK


12.CHECK HARNESS AND CONNECTOR (DEFOG RELAY - BATTERY)
B191462E02
  1. Remove the DEFOG relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    DEFOG relay terminal 1 - Body ground
    Ignition switch ON
    11 to 14 V
    DEFOG relay terminal 5 - Body ground
    Always
    11 to 14 V

  1. Reinstall the DEFOG relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13.CHECK HARNESS AND CONNECTOR (DEFOG RELAY - AIR CONDITIONING AMPLIFIER)
B191476E02
  1. Remove the DEFOG relay from the engine room relay block.

  1. Disconnect the H24 air conditioning amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    DEFOG relay terminal 2 - H24-38 (RDEF)
    Always
    Below 1 Ω

  1. Reconnect the air conditioning amplifier connector.

  1. Reinstall the DEFOG relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.CHECK HARNESS AND CONNECTOR (REAR WINDOW DEFOGGER - DEFOG RELAY, BODY GROUND)
B191477E02
  1. Disconnect the V11 and V12 defogger connectors.

  1. Remove the DEFOG relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    V11-1(B) - DEFOG relay terminal 3
    Always
    Below 1 Ω
    V12-1(E) - Body ground
    Always
    Below 1 Ω
    DEFOG relay terminal 4 - Body ground
    Always
    Below 1 Ω
    V11-1(B) - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the DEFOG relay .

  1. Reconnect the defogger connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER (Click here)