Home › Power Source / Network · NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Short to GND in CAN Bus Line

for Preparation Click here


DESCRIPTION

There may be a short circuit between the CAN bus lines and GND when the resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.

Symptom
Trouble Area
The resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.
  1. Short between CAN bus lines and GND
  2. ECM
  3. Air conditioning amplifier assembly
  4. 4 wheel drive control ECU (4WD control ECU)*1
  5. Bus buffer ECU*2
  6. Network gateway ECU*3
  7. Center airbag sensor assembly
  8. Steering angle sensor
  9. Main body ECU (cowl side junction block LH)
  10. Power steering ECU assembly
  11. Brake actuator assembly (skid control ECU)
  12. Suspension control ECU*4
  13. Combination meter assembly
  14. No. 1 junction connector
  15. No. 2 junction connector
  16. No. 4 junction connector*4
*1 for 4WD
*2: w/ Bus Buffer ECU
*3: w/ Network Gateway ECU
*4: w/ Air Suspension System

WIRING DIAGRAM


C242851E01


C242852E01


C242853E01


INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


NEXT


2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - DLC3)


    C242750E23
  1. Disconnect the H119 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H119-3 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H119-14 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


4.CONNECT CONNECTOR
  1. Reconnect the H119 No. 1 junction connector.


NEXT


5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR SIDE)


    C201374E84
  1. Disconnect the H115 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H19-6 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H19-14 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 21
OK


6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)


    C242750E86
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H115-1 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H115-12 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 11
OK


7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - 4WD CONTROL ECU)

NOTICE:
For vehicles without an 4WD, go to "Check for Short to GND in CAN Bus Wire (No. 2 Junction Connector - Bus Buffer ECU)".



    C242750E87
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H115-2 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H115-13 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 13
OK


8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - BUS BUFFER ECU)

NOTICE:
For vehicles without an bus buffer ECU, go to "Check for Short to GND in CAN Bus Wire (No. 2 Junction Connector - Network Gateway ECU)".



    C242750E88
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H115-5 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H115-16 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 15
OK


9.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

NOTICE:
For vehicles without an network gateway ECU, go to "Check for Short to GND in CAN Bus Wire (No. 2 Junction Connector - ECM)".



    C242750E89
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H115-6 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H115-17 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 17
OK


10.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - ECM)


    C242750E90
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H115-3 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H115-14 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 19
OK

REPLACE NO. 2 JUNCTION CONNECTOR 

11.CONNECT CONNECTOR
  1. Reconnect the H115 No. 2 junction connector.


NEXT


12.CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)


    C242944E02
  1. Disconnect the H24 air conditioning amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H24-11 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H24-12 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Air Conditioning Amplifier Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CANH, CANL)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

13.CONNECT CONNECTOR
  1. Reconnect the H115 No. 2 junction connector.


NEXT


14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (4WD CONTROL ECU)


    C242945E03
  1. Disconnect the A28 4 wheel drive control ECU (4WD control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A28-19 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    A28-20 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to 4 Wheel Drive Control ECU [4WD Control ECU])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO 4WD CONTROL ECU (CANH, CANL)
OK

REPLACE 4 WHEEL DRIVE CONTROL ECU (4WD CONTROL ECU) (Click here)  

15.CONNECT CONNECTOR
  1. Reconnect the H115 No. 2 junction connector.


NEXT


16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (BUS BUFFER ECU)


    C242946E02
  1. Disconnect the H66 bus buffer ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H66-3 (CAN+) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H66-2 (CAN-) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Bus Buffer ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BUS BUFFER ECU (CAN+, CAN-)
OK

REPLACE BUS BUFFER ECU 

17.CONNECT CONNECTOR
  1. Reconnect the H115 No. 2 junction connector.


NEXT


18.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NETWORK GATEWAY ECU)


    C242947E02
  1. Disconnect the H120 network gateway ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H120-16 (CA1H) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H120-15 (CA1L) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Network Gateway ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NETWORK GATEWAY ECU (CA1H, CA1L)
OK

REPLACE NETWORK GATEWAY ECU (Click here)  

19.CONNECT CONNECTOR
  1. Reconnect the H115 No. 2 junction connector.


NEXT


20.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM)


    C242948E02
  1. Disconnect the A27 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A27-10 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    A27-11 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)
    *b
    Front view of DLC3
    Result 
    Result
    Proceed to
    OK (for 1UR-FE)
    A
    OK (for 3UR-FE)
    B
    OK (for 3UR-FBE)
    C
    NG
    D



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
A

REPLACE ECM (Click here)  

21.CONNECT CONNECTOR
  1. Reconnect the H115 No. 2 junction connector.


NEXT


22.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    C242750E29
  1. Disconnect the H119 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H119-5 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H119-16 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3
    Result 
    Result
    Proceed to
    OK (w/ Air Suspension System)
    A
    OK (w/o Air Suspension System)
    B
    NG
    C



B
Go to step 33

C
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
A


23.CONNECT CONNECTOR
  1. Reconnect the H119 No. 1 junction connector.


NEXT


24.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR SIDE)


    C201374E84
  1. Disconnect the O41 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H19-6 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H19-14 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 31
OK


25.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - SUSPENSION CONTROL ECU)


    C242949E03
  1. Disconnect the O42 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O42-6 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O42-12 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 27
OK


26.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)


    C242949E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O41-1 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O41-7 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 29
OK

REPLACE NO. 4 JUNCTION CONNECTOR 

27.CONNECT CONNECTOR
  1. Reconnect the O41 and O42 No. 4 junction connectors.


NEXT


Go to step 29

28.CHECK FOR SHORT TO GND IN CAN BUS WIRE (SUSPENSION CONTROL ECU)


    C242950E02
  1. Disconnect the O16 suspension control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O16-7 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O16-8 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Suspension Control ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SUSPENSION CONTROL ECU (CANH, CANL)
OK

REPLACE SUSPENSION CONTROL ECU (Click here)  

29.CONNECT CONNECTOR
  1. Reconnect the O41 and O42 No. 4 junction connectors.


NEXT


30.CHECK FOR SHORT TO GND IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)


    C242945E04
  1. Disconnect the H37 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H37-33 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H37-34 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Combination Meter Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

31.CONNECT CONNECTOR
  1. Reconnect the O41 No. 4 junction connector.


NEXT


32.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)


    C242750E36
  1. Disconnect the H119 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H119-2 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H119-13 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
OK


33.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)


    C242750E31
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H119-1 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H119-12 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 39
OK


34.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)


    C242750E32
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H119-4 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H119-15 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 41
OK


35.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - MAIN BODY ECU)


    C242750E33
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H119-6 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H119-17 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 43
OK


36.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)


    C242750E34
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H119-7 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H119-18 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 45
OK


37.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU)


    C242750E35
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H119-9 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H119-20 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3
    Result 
    Result
    Proceed to
    OK (w/ Air Suspension System)
    A
    OK (w/o Air Suspension System)
    B
    NG
    C



B
Go to step 38

C
Go to step 47
A

REPLACE NO. 1 JUNCTION CONNECTOR 

38.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)


    C242750E36
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H119-2 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H119-13 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 49
OK

REPLACE NO. 1 JUNCTION CONNECTOR 

39.CONNECT CONNECTOR
  1. Reconnect the H119 No. 1 junction connector.


NEXT


40.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY)


    C242951E02
  1. Disconnect the H56 center airbag sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H56-13 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H56-22 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CANH, CANL)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

41.CONNECT CONNECTOR
  1. Reconnect the H119 No. 1 junction connector.


NEXT


42.CHECK FOR SHORT TO GND IN CAN BUS WIRE (STEERING ANGLE SENSOR)


    C242952E02
  1. Disconnect the H6 steering angle sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H6-10 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H6-9 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Steering Angle Sensor)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)
OK

REPLACE STEERING ANGLE SENSOR (Click here)  

43.CONNECT CONNECTOR
  1. Reconnect the H119 No. 1 junction connector.


NEXT


44.CHECK FOR SHORT TO GND IN CAN BUS WIRE (MAIN BODY ECU)


    C242953E02
  1. Disconnect the H2 main body ECU (cowl side junction block LH) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H2-5 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H2-6 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Main Body ECU [Cowl Side Junction Block LH])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) 

45.CONNECT CONNECTOR
  1. Reconnect the H119 No. 1 junction connector.


NEXT


46.CHECK FOR SHORT TO GND IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY)


    C242957E02
  1. Disconnect the H117 power steering ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H117-1 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H117-2 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Steering ECU Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU ASSEMBLY (CANH, CANL)
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)  

47.CONNECT CONNECTOR
  1. Reconnect the H119 No. 1 junction connector.


NEXT


48.CHECK FOR SHORT TO GND IN CAN BUS WIRE (SKID CONTROL ECU)


    C242958E02
  1. Disconnect the A19 brake actuator assembly (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A19-12 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    A19-13 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Brake Actuator Assembly [Skid Control ECU])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (Click here)  

49.CONNECT CONNECTOR
  1. Reconnect the H119 No. 1 junction connector.


NEXT


50.CHECK FOR SHORT TO GND IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)


    C242945E04
  1. Disconnect the H37 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H37-33 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H37-34 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Combination Meter Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)