Home › Engine / Hybrid System › 3UR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > REMOVAL

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).



1. DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.
  2. After discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the fuel pump ECU connector (Click here).

  1. Connect the cable to the negative (-) battery terminal.

  1. Start the engine. After the engine has stopped on its own, turn the ignition switch off.

    HINT:
    DTC P0171/0174 (system too lean) may be set.

  1. Crank the engine again, and then check that the engine does not start.

  1. Loosen the fuel tank cap, and then discharge the pressure in the fuel tank completely.

  1. Connect the fuel pump ECU connector (Click here).



2. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).



4. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and gasket, and drain the engine oil into a container.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



5. REMOVE HOOD SUB-ASSEMBLY


    A160839
  1. Using a screwdriver, release the 2 clips and remove the hood support assembly.

    HINT:
    Tape the screwdriver tip before use.

    CAUTION:
    Remove the hood support assembly while supporting the hood by hand.

  1. Remove the 4 bolts and hood.



6. REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY
  1. Remove the windshield wiper motor (Click here).



7. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY
  1. Disconnect the 2 washer hoses.



    A183287
  1. Remove the 7 bolts and outer panel.



8. REMOVE RADIATOR ASSEMBLY
  1. Remove the radiator assembly (Click here).



9. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
  1. for 2WD:
    Remove the transmission assembly (Click here).

  1. for 4WD:
    Remove the transmission assembly (Click here).



10. REMOVE AIR CLEANER ASSEMBLY


    A183242
  1. Loosen the hose clamp and disconnect the air cleaner from the air cleaner hose.

  1. Loosen the 2 bolts and remove the air cleaner with the grommet.



11. REMOVE AIR CLEANER HOSE ASSEMBLY


    A183244
  1. Disconnect the No. 2 ventilation hose.

  1. Disconnect the vacuum hose.

  1. Loosen the hose clamp and remove the air cleaner hose.



12. DISCONNECT INLET HEATER WATER HOSE C


    A183230
  1. Slide the clamp and disconnect the inlet heater water hose C from the water by-pass pipe sub-assembly.



13. DISCONNECT OUTLET HEATER WATER HOSE C


    A183228
  1. Slide the clamp and disconnect the outlet heater water hose C from the No. 1 water by-pass pipe.



14. DISCONNECT VACUUM HOSE ASSEMBLY


    A183279
  1. Disconnect the vacuum hose from the brake booster.



15. REMOVE PURGE LINE HOSE


    A183280
  1. Remove the purge line hose.



16. DISCONNECT FUEL MAIN AND RETURN HOSE


    A308865E03
  1. Remove the fuel pipe clamp.

  1. Disconnect the fuel main and return hoses (Click here).



17. SEPARATE ECM


    A183282
  1. Disconnect the clamp and ECM connector.

    HINT:
    Refer to the following procedures to disconnect the ECM connector .



18. SEPARATE ENGINE WIRE


    A160782E01
  1. Disconnect the 4 connectors from the connector holder block.

  1. Remove the bolt and disconnect the ground wire.



    A163790
  1. Remove the nut and disconnect the wire from the positive (+) battery cable.

  1. Disconnect the cable from the positive (+) battery terminal.

  1. Remove the bolt and disconnect the ground wire.

  1. Remove the nut and disconnect the wire and 2 clips from the engine room junction block.

  1. Disconnect the 2 connectors and 2 clips from the engine room junction block.



19. SEPARATE COOLER COMPRESSOR ASSEMBLY


    A163332
  1. Remove the 2 bolts, 2 nuts and 2 stud bolts, and disconnect the cooler compressor assembly.

    HINT:
    It is not necessary to completely remove the cooler compressor assembly. With the hoses connected to the cooler compressor assembly, hang the cooler compressor assembly on the vehicle body with a rope.



20. REMOVE GENERATOR ASSEMBLY
  1. Remove the generator assembly (Click here).



21. REMOVE EXHAUST MANIFOLD
  1. Remove the exhaust manifold (Click here).



22. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY


    A163778E01
  1. Using SST, hold the crankshaft.

    SST
    09213-70011  
    09330-00021  



    A163779
  1. Remove the 10 bolts, rear drive plate spacer, drive plate and crankshaft angle sensor rotor.



23. REMOVE NO. 1 WATER BY-PASS PIPE


    A183283
  1. Remove the 2 bolts, disconnect the hose, and then remove the No. 1 water by-pass pipe.



24. REMOVE OIL COOLER TUBE
  1. Remove the bolt and oil cooler tube from the oil pan.



25. REMOVE ENGINE ASSEMBLY


    A163784E01
  1. Install the 2 engine hangers with the 2 bolts as shown in the illustration.

    HINT:
    Item
    Part No.
    Engine hanger
    12281-38030, 12281-38060
    Bolt
    90119-14120, 90119-A0166

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Attach an engine sling device and hang the engine with a chain block.



    A163780E01
  1. Remove the 4 engine mounting insulator bolts.

  1. Lift the engine out from the vehicle slowly and carefully.

    NOTICE:
    Make sure the engine is clear of all wiring, hoses and cables.



26. INSTALL ENGINE ON ENGINE STAND
  1. Install the engine onto an engine stand with the bolts.

  1. Remove the 2 bolts and 2 engine hangers.