Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM
RM27L0U _51 Engine / Hybrid System _049293 3UR-FBE ENGINE CONTROL _0235531 SFI SYSTEM J

3UR-FBE ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates 5 V power from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A379702E02
4.354,1.031 6.25,1.219 1.896,0.188 10 false 5 V Constant Voltage Circuit 5.365,1.875 6.385,2.063 1.021,0.188 10 false Microprocessor 2.917,0.865 3.385,1.063 0.469,0.198 10 false BATT 3,1.208 3.302,1.406 0.302,0.198 10 false +B 3.135,2.146 3.438,2.344 0.302,0.198 10 false VC 4.958,3.229 5.427,3.427 0.469,0.198 10 false ECM 4.073,3.01 4.271,3.208 0.198,0.198 10 false R 1.24,0.99 2.573,1.208 1.333,0.219 10 false from EFI NO. 1 Fuse 1.198,1.313 2.573,1.51 1.375,0.198 10 false from EFI MAIN Relay 0.208,1.906 2.667,2.438 2.458,0.531 10 false to Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (Sensors which have ICs) 0.188,2.854 2.635,3.385 2.448,0.531 10 false to Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc.

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

A220560E01
5.322,1.003 5.595,1.144 0.273,0.141 10 D56 5.322,1.426 5.595,1.567 0.273,0.141 10 D56 5.322,1.837 5.595,1.979 0.273,0.141 10 D56 5.322,2.556 5.595,2.697 0.273,0.141 10 D56 5.322,2.964 5.595,3.105 0.273,0.141 10 D56 5.322,3.673 5.595,3.814 0.273,0.141 10 D56 5.322,4.083 5.595,4.225 0.273,0.141 10 D56 5.322,4.777 5.595,4.919 0.273,0.141 10 D56 5.324,5.197 5.597,5.338 0.273,0.141 10 D56 5.324,5.93 5.597,6.071 0.273,0.141 10 D56 5.319,6.345 5.593,6.486 0.273,0.141 10 D56 5.375,6.172 5.549,6.317 0.174,0.144 10 65 5.374,5.752 5.550,5.891 0.176,0.139 10 64 5.677,6.352 6.010,6.499 0.333,0.147 10 EV2- 5.677,5.927 6.041,6.074 0.364,0.147 10 EV2+ 5.677,5.196 6.039,5.336 0.362,0.140 10 VV2- 5.677,4.785 6.039,4.924 0.362,0.140 10 VV2+ 5.375,4.598 5.548,4.741 0.173,0.142 10 87 5.375,5.025 5.548,5.167 0.173,0.141 10 88 5.372,3.482 5.552,3.624 0.180,0.142 10 69 5.374,3.915 5.550,4.057 0.176,0.142 10 68 5.374,2.792 5.549,2.934 0.175,0.142 10 91 5.374,2.376 5.549,2.518 0.175,0.142 10 92 5.336,1.666 5.587,1.810 0.251,0.144 10 111 5.335,1.259 5.588,1.401 0.253,0.142 10 110 5.371,0.837 5.552,0.981 0.181,0.144 10 66 5.677,0.912 6.078,1.067 0.401,0.155 10 VCV2 5.677,1.436 5.978,1.582 0.301,0.146 10 NE+ 5.677,1.836 5.978,1.982 0.301,0.146 10 NE- 5.677,2.562 6.045,2.716 0.368,0.154 10 VV1+ 5.677,2.966 6.045,3.120 0.368,0.154 10 VV1- 5.677,3.664 6.046,3.814 0.369,0.150 10 EV1+ 5.677,4.096 6.017,4.242 0.339,0.146 10 EV1- 2.923,0.912 3.034,1.059 0.111,0.147 10 3 2.923,1.333 3.039,1.478 0.116,0.144 10 1 2.923,1.745 3.044,1.894 0.121,0.149 10 2 2.923,2.259 3.034,2.406 0.111,0.147 10 3 2.923,2.47 3.039,2.614 0.116,0.144 10 1 2.923,2.881 3.044,3.030 0.121,0.149 10 2 2.923,3.385 3.034,3.532 0.111,0.147 10 3 2.923,3.596 3.039,3.740 0.116,0.144 10 1 2.923,4.008 3.044,4.156 0.121,0.149 10 2 2.923,4.486 3.034,4.633 0.111,0.147 10 3 2.923,4.697 3.039,4.841 0.116,0.144 10 1 2.923,5.109 3.044,5.258 0.121,0.149 10 2 2.923,5.638 3.034,5.786 0.111,0.147 10 3 2.923,5.85 3.039,5.994 0.116,0.144 10 1 2.923,6.261 3.044,6.410 0.121,0.149 10 2 2.596,1.014 2.811,1.155 0.214,0.141 10 VC 2.505,1.426 2.810,1.567 0.305,0.141 10 NE+ 2.544,1.845 2.810,1.988 0.266,0.144 10 NE- 2.596,2.353 2.811,2.494 0.214,0.141 10 VC 2.438,2.562 2.809,2.703 0.371,0.141 10 VVL+ 2.48,2.972 2.810,3.116 0.329,0.144 10 VVL- 2.512,3.467 2.810,3.607 0.297,0.141 10 VC2 2.522,3.688 2.810,3.829 0.288,0.141 10 EX+ 2.552,4.097 2.810,4.238 0.258,0.141 10 EX- 2.596,4.58 2.811,4.721 0.214,0.141 10 VC 2.418,4.79 2.809,4.931 0.391,0.141 10 VVR+ 2.449,5.2 2.809,5.344 0.360,0.144 10 VVR- 2.512,5.717 2.810,5.858 0.297,0.141 10 VC2 2.522,5.939 2.810,6.079 0.288,0.141 10 EX+ 2.552,6.348 2.810,6.488 0.258,0.141 10 EX- 6.142,7.446 6.478,7.599 0.335,0.152 10 ECM 0.233,1.001 0.437,1.150 0.205,0.149 10 D1 0.233,1.156 1.958,1.311 1.725,0.156 10 Crankshaft Position Sensor 0.233,2.339 0.528,2.488 0.295,0.149 10 D22 0.233,2.494 2.000,2.809 1.767,0.316 10 VVT Sensor (for Intake Side of Bank 1) 0.233,3.453 0.528,3.602 0.295,0.149 10 D24 0.233,3.607 2.104,3.923 1.871,0.316 10 VVT Sensor (for Exhaust Side of Bank 1) 0.233,4.565 0.528,4.714 0.295,0.149 10 D23 0.233,4.719 2.000,5.034 1.767,0.316 10 VVT Sensor (for Intake Side of Bank 2) 0.233,5.704 0.528,5.853 0.295,0.149 10 D25 0.233,5.858 2.104,6.174 1.871,0.316 10 VVT Sensor (for Exhaust Side of Bank 2)

A242728E03
5.322,5.761 5.595,5.903 0.273,0.141 10 D56 5.322,6.174 5.595,6.315 0.273,0.141 10 D56 5.386,5.588 5.566,5.735 0.180,0.147 10 90 5.387,5.995 5.565,6.138 0.178,0.143 10 89 5.649,5.764 5.863,5.908 0.214,0.144 10 G2 5.649,6.179 5.904,6.331 0.254,0.152 10 G2- 2.909,5.268 3.020,5.416 0.111,0.147 10 3 2.909,5.678 3.025,5.822 0.116,0.144 10 1 2.909,6.089 3.030,6.238 0.121,0.149 10 2 2.582,5.357 2.797,5.498 0.214,0.141 10 VC 2.593,5.765 2.797,5.906 0.204,0.141 10 G2 2.623,6.176 2.797,6.319 0.174,0.144 10 G- 0.219,5.373 0.423,5.522 0.205,0.149 10 D2 0.219,5.527 1.944,5.683 1.725,0.156 10 Camshaft Position Sensor 5.651,0.841 6.064,0.997 0.413,0.156 10 VCV1 5.336,0.964 5.617,1.120 0.281,0.156 10 D56 5.376,0.792 5.560,0.934 0.184,0.142 10 67 5.647,1.304 5.910,1.460 0.264,0.156 10 AIP 5.332,1.307 5.613,1.463 0.281,0.156 10 A27 5.372,1.15 5.556,1.292 0.184,0.142 10 54 5.647,1.572 6.060,1.728 0.413,0.156 10 ETHA 5.332,1.681 5.613,1.837 0.281,0.156 10 D56 5.372,1.523 5.556,1.665 0.184,0.142 10 98 5.641,2.424 5.976,2.580 0.335,0.156 10 AIP2 5.34,2.427 5.621,2.583 0.281,0.156 10 A27 5.38,2.27 5.564,2.412 0.184,0.142 10 53 5.641,2.736 6.099,2.891 0.458,0.156 10 ETHW 5.34,2.638 5.621,2.794 0.281,0.156 10 D56 5.34,3.352 5.621,3.508 0.281,0.156 10 D56 5.34,4.475 5.621,4.631 0.281,0.156 10 D56 5.38,2.792 5.564,2.934 0.184,0.142 10 97 0.203,0.915 0.502,1.070 0.299,0.156 10 D37 0.203,1.055 2.183,1.234 1.980,0.179 10 Air Switching Valve (for Bank 1) 0.203,2.191 0.502,2.347 0.299,0.156 10 D38 0.203,2.331 2.183,2.510 1.980,0.179 10 Air Switching Valve (for Bank 2) 2.603,0.948 2.828,1.104 0.225,0.156 10 VC 2.911,0.859 3.020,1.015 0.110,0.156 10 2 2.911,1.21 3.020,1.366 0.110,0.156 10 3 2.572,1.298 2.839,1.454 0.267,0.156 10 AIP 2.626,1.674 2.829,1.830 0.202,0.156 10 E2 2.906,1.589 3.025,1.753 0.119,0.164 10 4 2.521,2.219 2.824,2.375 0.302,0.156 10 VC2 2.911,2.131 3.020,2.286 0.110,0.156 10 2 2.911,2.336 3.020,2.492 0.110,0.156 10 3 2.492,2.424 2.838,2.580 0.346,0.156 10 AIP2 2.553,2.634 2.824,2.790 0.271,0.156 10 E22 2.906,2.548 3.025,2.712 0.119,0.164 10 4 5.637,3.339 5.942,3.495 0.305,0.156 10 PSP 5.376,3.203 5.557,3.352 0.180,0.149 10 72 5.642,4.463 6.073,4.612 0.430,0.149 10 PPMP 5.346,4.319 5.595,4.475 0.250,0.156 10 121 0.21,3.127 0.504,3.282 0.295,0.156 10 D30 0.21,3.276 1.402,3.603 1.193,0.327 10 Power Steering Oil Pressure Sensor 2.609,3.141 2.835,3.306 0.225,0.165 10 VC 2.517,3.344 2.825,3.499 0.309,0.156 10 PSP 2.625,3.717 2.836,3.873 0.211,0.156 10 E2 2.902,3.057 3.012,3.213 0.110,0.156 10 1 2.898,3.26 3.008,3.416 0.110,0.156 10 2 2.898,3.634 3.008,3.790 0.110,0.156 10 3 0.204,4.221 0.507,4.386 0.303,0.165 10 O24 0.204,4.368 1.836,4.543 1.633,0.174 10 Canister Pressure Sensor 2.493,4.26 2.834,4.415 0.341,0.156 10 VCC 2.4,4.469 2.824,4.634 0.424,0.165 10 VOUT 2.391,4.835 2.833,5.000 0.443,0.165 10 SGND 2.894,4.179 3.013,4.335 0.119,0.156 10 6 2.894,4.39 3.013,4.546 0.119,0.156 10 7 2.894,4.751 3.013,4.906 0.119,0.156 10 8 6.089,7.047 6.437,7.194 0.348,0.146 10 ECM 5.641,5.259 6.053,5.415 0.413,0.156 10 VCV2 5.331,5.345 5.612,5.501 0.281,0.156 10 D56 5.386,5.195 5.566,5.342 0.180,0.147 10 66

A165789E19
5.385,0.872 5.576,1.028 0.191,0.156 10 80 5.644,0.937 6.043,1.093 0.399,0.156 10 VCTA 5.34,1.023 5.617,1.168 0.277,0.145 10 D56 5.385,1.24 5.576,1.395 0.191,0.156 10 78 5.34,1.391 5.617,1.536 0.277,0.145 10 D56 5.385,1.607 5.576,1.763 0.191,0.156 10 77 5.34,1.759 5.617,1.904 0.277,0.145 10 D56 5.385,1.971 5.576,2.127 0.191,0.156 10 79 5.34,2.122 5.617,2.268 0.277,0.145 10 D56 5.644,1.387 6.026,1.536 0.382,0.149 10 VTA1 5.644,1.754 6.026,1.903 0.382,0.149 10 VTA2 5.644,2.042 5.960,2.191 0.316,0.149 10 ETA 5.389,2.413 5.579,2.558 0.191,0.145 10 57 5.344,2.555 5.618,2.704 0.274,0.149 10 A27 5.389,2.774 5.579,2.919 0.191,0.145 10 59 5.344,2.916 5.618,3.065 0.274,0.149 10 A27 5.389,3.142 5.579,3.288 0.191,0.145 10 55 5.344,3.285 5.618,3.434 0.274,0.149 10 A27 5.389,3.535 5.579,3.680 0.191,0.145 10 56 5.344,3.677 5.618,3.826 0.274,0.149 10 A27 5.389,3.902 5.579,4.047 0.191,0.145 10 58 5.344,4.045 5.618,4.194 0.274,0.149 10 A27 5.389,4.268 5.579,4.414 0.191,0.145 10 60 5.344,4.411 5.618,4.560 0.274,0.149 10 A27 5.644,2.468 6.050,2.624 0.406,0.156 10 VCPA 5.644,3.284 5.957,3.440 0.312,0.156 10 VPA 5.644,3.967 5.957,4.123 0.312,0.156 10 EPA 5.644,3.676 6.019,3.832 0.375,0.156 10 VPA2 5.644,4.331 6.019,4.487 0.375,0.156 10 EPA2 5.644,2.84 6.050,2.996 0.406,0.156 10 VCP2 0.219,1.008 0.444,1.164 0.225,0.156 10 D4 0.219,1.15 1.741,1.306 1.522,0.156 10 Throttle Position Sensor 2.594,1.022 2.828,1.178 0.235,0.156 10 VC 2.521,1.387 2.829,1.541 0.309,0.154 10 VTA 2.453,1.741 2.826,1.906 0.373,0.165 10 VTA2 2.624,2.111 2.840,2.276 0.216,0.165 10 E2 2.904,0.938 3.023,1.094 0.119,0.156 10 5 2.904,1.297 3.023,1.452 0.119,0.156 10 6 2.904,1.663 3.023,1.819 0.119,0.156 10 4 2.904,2.022 3.023,2.178 0.119,0.156 10 3 0.21,2.537 0.500,2.693 0.290,0.156 10 A17 0.21,2.68 1.347,3.012 1.137,0.332 10 Accelerator Pedal Position Sensor 2.433,2.561 2.847,2.711 0.414,0.150 10 VCPA 2.433,2.925 2.847,3.076 0.414,0.150 10 VCP2 2.522,3.285 2.843,3.435 0.321,0.150 10 VPA 2.447,3.682 2.861,3.832 0.414,0.150 10 VPA2 2.527,4.037 2.849,4.187 0.321,0.150 10 EPA 2.452,4.41 2.866,4.560 0.414,0.150 10 EPA2 2.904,2.465 3.023,2.626 0.119,0.161 10 4 2.904,2.825 3.023,2.986 0.119,0.161 10 1 2.904,3.185 3.023,3.345 0.119,0.161 10 6 2.904,3.582 3.023,3.742 0.119,0.161 10 3 2.904,3.958 3.023,4.118 0.119,0.161 10 5 2.904,4.317 3.023,4.478 0.119,0.161 10 2 6.144,5.159 6.474,5.308 0.330,0.149 10 ECM

PROCEDURE

1.CHECK MIL
a.

Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.

OK:

MIL lights up




OK

SYSTEM OK

NG

2.CHECK COMMUNICATION BETWEEN TECHSTREAM AND ECM
2.CHECK COMMUNICATION BETWEEN TECHSTREAM AND ECM
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and Techstream ON.


c.

Check the communication between the Techstream and ECM.

Result
Result Proceed to
Communication is possible A
Communication is not possible B



B

3.CHECK MIL (THROTTLE POSITION SENSOR)

A

3.CHECK MIL (THROTTLE POSITION SENSOR)
a.

Disconnect the D4 throttle body assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B

HINT:

Perform "Inspection After Repair" after repairing or replacing the throttle body assembly (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




B

4.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)

A

4.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the A17 accelerator pedal position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

5.CHECK MIL (CANISTER PUMP MODULE)

A

5.CHECK MIL (CANISTER PUMP MODULE)
a.

Disconnect the O24 canister pump module connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

6.CHECK MIL (AIR SWITCHING VALVE ASSEMBLY (for Bank 1))

A

6.CHECK MIL (AIR SWITCHING VALVE ASSEMBLY (for Bank 1))
a.

Disconnect the D37 air switching valve assembly (for Bank 1) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

7.CHECK MIL (AIR SWITCHING VALVE ASSEMBLY (for Bank 2))

A

7.CHECK MIL (AIR SWITCHING VALVE ASSEMBLY (for Bank 2))
a.

Disconnect the D38 air switching valve assembly (for Bank 2) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

8.CHECK MIL (POWER STEERING OIL PRESSURE SENSOR)

A

8.CHECK MIL (POWER STEERING OIL PRESSURE SENSOR)
a.

Disconnect the D30 power steering oil pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

9.CHECK MIL (CAMSHAFT POSITION SENSOR)

A

9.CHECK MIL (CAMSHAFT POSITION SENSOR)
a.

Disconnect the D2 camshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

10.CHECK MIL (CRANKSHAFT POSITION SENSOR)

A

10.CHECK MIL (CRANKSHAFT POSITION SENSOR)
a.

Disconnect the D1 crankshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

11.CHECK MIL (VVT SENSOR (for Intake Side of Bank 1))

A

11.CHECK MIL (VVT SENSOR (for Intake Side of Bank 1))
a.

Disconnect the D22 VVT sensor (for Intake Side of Bank 1) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

12.CHECK MIL (VVT SENSOR (for Exhaust Side of Bank 1))

A

REPLACE VVT SENSOR (for Intake Side of Bank 1)

12.CHECK MIL (VVT SENSOR (for Exhaust Side of Bank 1))
a.

Disconnect the D24 VVT sensor (for Exhaust Side of Bank 1) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

13.CHECK MIL (VVT SENSOR (for Intake Side of Bank 2))

A

REPLACE VVT SENSOR (for Exhaust Side of Bank 1)

13.CHECK MIL (VVT SENSOR (for Intake Side of Bank 2))
a.

Disconnect the D23 VVT sensor (for Intake Side of Bank 2) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

14.CHECK MIL (VVT SENSOR (for Exhaust Side of Bank 2))

A

REPLACE VVT SENSOR (for Intake Side of Bank 2)

14.CHECK MIL (VVT SENSOR (for Exhaust Side of Bank 2))
a.

Disconnect the D25 VVT sensor (for Exhaust Side of Bank 2) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

15.CHECK HARNESS AND CONNECTOR

A

REPLACE VVT SENSOR (for Exhaust Side of Bank 2)

15.CHECK HARNESS AND CONNECTOR
a.

Disconnect the D4 throttle body assembly connector.


b.

Disconnect the A17 accelerator pedal position sensor connector.


c.

Disconnect the O24 canister pump module connector.


d.

Disconnect the D37 air switching valve assembly (for Bank 1) connector.


e.

Disconnect the D38 air switching valve assembly (for Bank 2) connector.


f.

Disconnect the D30 power steering oil pressure sensor connector.


g.

Disconnect the D2 camshaft position sensor connector.


h.

Disconnect the D1 crankshaft position sensor connector.


i.

Disconnect the D22 VVT sensor (for Intake Side of Bank 1) connector.


j.

Disconnect the D24 VVT sensor (for Exhaust Side of Bank 1) connector.


k.

Disconnect the D23 VVT sensor (for Intake Side of Bank 2) connector.


l.

Disconnect the D25 VVT sensor (for Exhaust Side of Bank 2) connector.


m.

Disconnect the A27 and D56 ECM connectors.


n.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D56-80 (VCTA) - Body ground Always 10 kΩ or higher
A27-57 (VCPA) - Body ground Always 10 kΩ or higher
A27-59 (VCP2) - Body ground Always 10 kΩ or higher
D56-66 (VCV2) - Body ground Always 10 kΩ or higher
D56-67 (VCV1) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR