The fuel pump circuit consists of the ECM, fuel pump and fuel pump ECU (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump ECU. Based on the signal sent from the ECM, the fuel pump ECU adjusts the fuel pump operation speed.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.
Check whether operating sounds can be heard while operating the fuel pump using the Techstream.
Operating sounds can be heard from fuel pump.
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Disconnect the fuel pump ECU connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| O44-6 (+B) - Body Ground | Ignition switch ON | 11 to 14 V |
OK
NG
Disconnect the fuel pump ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O44-3 (E) - Body ground | Always | Below 1 Ω |
OK
NG
Disconnect the fuel pump connector.
Disconnect the fuel pump ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q1-4 (B2) - O44-1 (FP) | Always | Below 1 Ω |
| Q1-5 (E2) - O44-2 (FP-) | Always | Below 1 Ω |
| Q1-4 (B2) or O44-1 (FP) - Body ground | Always | 10 kΩ or higher |
| Q1-5 (E2) or O44-2 (FP-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Inspect the fuel pump (See page Engine / Hybrid System>3UR-FE FUEL>FUEL PUMP>INSPECTION).
Perform "Inspection After Repair" after replacing the fuel pump (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
OK
NG
Disconnect the fuel pump ECU connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O44-5 (FPC) - A27-52 (FPC) | Always | Below 1 Ω |
| O44-5 (FPC) or A27-52 (FPC) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the fuel pump ECU (See page Engine / Hybrid System>3UR-FE FUEL>FUEL PUMP ECU>REMOVAL).
NEXT
Check the fuel pump operation.
Malfunction has been repaired successfully.
OK
NG
Inspect the fuel pump relay (F/PMP) (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION).
OK
NG
Remove the fuel pump relay (F/PMP) from the engine room relay block.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F/PMP relay (1) - Body ground | Ignition switch ON | 11 to 14 V |
| F/PMP relay (5) - Body ground | Always | 11 to 14 V |
OK
NG
Remove the fuel pump relay (F/PMP) from the engine room relay block.
Disconnect the fuel pump ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F/PMP relay (3) - O44-6 (+B) | Always | Below 1 Ω |
| F/PMP relay (3) or O44-6 (+B) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the cable from the battery negative (-) terminal.
Disconnect the cable from the battery positive (+) terminal.
Remove the fuel pump relay (F/PMP) from the engine room relay block.
Remove the integration relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F/PMP relay (1) - 1B-4 | Always | Below 1 Ω |
| F/PMP relay (5) - Battery positive (+) terminal | Always | Below 1 Ω |
| F/PMP relay (2) - Body ground | Always | Below 1 Ω |
| F/PMP relay (1) or 1B-4 - Body ground | Always | 10 kΩ or higher |
| F/PMP relay (5) or Battery positive (+) terminal - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the fuel tank assembly (See page Engine / Hybrid System>3UR-FE FUEL>FUEL TANK>REMOVAL).
Remove the fuel pump from the fuel tank assembly.
Clean the fuel pump to completely remove any remaining fuel.
Connect the fuel pump connector.
Confirm that no fuel remains inside or on the outside of the fuel pump.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump Duty.
Operate the fuel pump using the active test function and measure the voltage according to the value(s) in the table below.
| Tester Connection | Techstream Operation | Specified Condition |
|---|---|---|
| 1 - 2 | FPC Duty: 25% | 3.2 to 4.05 V |
| FPC Duty: 80% | 8.8 to 12.5 V |
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Operate the fuel pump using the active test function and measure the voltage according to the value(s) in the table below.
| Tester Connection | Techstream Operation | Specified Condition |
|---|---|---|
| 1 - 2 | ON (FPC Duty: 90%) | 9.0 to 14.0 V |
Be sure to measure the voltage with all of the connectors connected.
Before performing this inspection, check that the battery voltage is between 11 and 14 V (not depleted).
OK
NG
Disconnect the fuel pump ECU connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O44-5 (FPC) - A27-52 (FPC) | Always | Below 1 Ω |
| O44-5 (FPC) or A27-52 (FPC) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the fuel pump (See page Engine / Hybrid System>3UR-FE FUEL>FUEL PUMP>REMOVAL).
Perform "Inspection After Repair" after replacing the fuel pump (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
NEXT
Replace the fuel pump ECU (See page Engine / Hybrid System>3UR-FE FUEL>FUEL PUMP ECU>REMOVAL).
NEXT
Check the fuel pump operation.
Malfunction has been repaired successfully.
OK
NG