Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM › 2015.08–2016.10
RM27L0U _51 Engine / Hybrid System _049294 3UR-FE ENGINE CONTROL _0235547 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P2440  Secondary Air Injection System Switching Valve Stuck Open Bank1  P2441  Secondary Air Injection System Switching Valve Stuck Close Bank1  P2442  Secondary Air Injection System Switching Valve Stuck Open Bank 2  P2443  Secondary Air Injection System Switching Valve Stuck Closed Bank 2  


DESCRIPTION

Refer to DTC P0412 (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>P0412).

DTC No. DTC Detection Condition Trouble Area
P2440
P2442
The pressure sensor detects pulsation of the exhaust gas despite the ECM commanding the Air Switching Valve (ASV) to close, while the engine is running (1 trip detection logic).
·

ASV

·

Open or short in ASV circuit

·

Pressure sensor

·

Pressure sensor circuit

·

Air Injection Control Driver (AID)

·

ECM


P2441
P2443
The pressure sensor detects no pulsation of the exhaust gas despite the ECM commanding the Air Switching Valve (ASV) to open, while the engine is running (2 trip detection logic).
·

ASV

·

Open or short in ASV circuit

·

Vacuum hose (ASV - pressure sensor)

·

Air injection hose

·

Pressure sensor

·

Pressure sensor circuit

·

Air Injection Control Driver (AID)

·

ECM



HINT:

Air switching valve normal operation:

When the Air Switching Valve (ASV) is open, exhaust gas pulsation occurs in the secondary air passage.

When the ASV is closed, exhaust gas pulsation does not occur in the secondary air passage.


MONITOR DESCRIPTION

The ECM monitors the pressure in the secondary air passage using the pressure sensor connected to the ASV of the Secondary Air Injection (AIR) system.

If either of the following conditions occurs, the ECM interprets it as a malfunction of the AIR system, and illuminates the MIL and sets a DTC:

·

Exhaust gas pulsation is detected by the pressure sensor despite the ECM commanding the ASV to close.

·

Exhaust gas pulsation is not detected by the pressure sensor despite the ECM commanding the ASV to open.


MONITOR STRATEGY

Related DTCs P2440: Air control valve stuck open
P2441: Air control valve stuck closed
P2442: Air control valve stuck open
P2443: Air control valve stuck closed
Required Sensors/Components (Main) Pressure sensor
Required Sensors/Components (Related) -
Frequency of Operation Once per drive cycle
Duration 2 seconds: P2440 Case 2, P2442 Case 2
7 seconds: Others
MIL Operation 1 driving cycle: P2440, P2442
2 driving cycles: Others
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

All
Monitor runs whenever following DTCs not present P0010, P0020 (VVT Oil control valve)
P0011, P0021 (VVT System - Advance)
P0012, P0022 (VVT System - Retard)
P0013, P0023 (Exhaust VVT Oil Control Valve)
P0014, P0024 (Exhaust VVT System - Advance)
P0015, P0025 (Exhaust VVT System - Retard)
P0016, P0018 (VVT System - Misalignment)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio Sensor Heater)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0171, P0172, P0174, P0175 (Fuel system)
P0301 - P0308 (Misfire)
P0327, P0328, P0332, P0333, P032C, P032D, P033C, P033D (Knock sensor)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P0351 - P0358 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0451, P0452, P0453 (EVAP system)
P0500, P0722 (Vehicle Speed Sensor)
P106B (Evap. emission control system Pressure Sensor - Air Injection System Pressure Sensor correlation)
P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor)
P1340 (Camshaft position sensor)
P2431 - P2438 (Secondary air injection system pressure sensor)
P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2, P21A3 (Air-fuel ratio imbalance)

P2440, P2442 (AIR valve is stuck open) (Case 1), P2441, P2443 (AIR valve is stuck closed)
Battery voltage 11 V or higher
Atmospheric pressure 45 kPa (337.5 mmHg) or more
Engine Running
AIR monitor during AIR: ON*1 Completed
AIR monitor during AIR: OFF*2 Completed
Air injection Driver (open/short or out of range) Not detected
AIR pressure sensor (open/short or out of range) Not detected

*1: AIR monitor during AIR: ON
Time after AIR in operation 5 seconds or more
AIR pump ON
AIR valve Open
Engine speed Less than 3550 rpm
Intake air amount Less than 99 gm/sec
Time after engine start 1 second or more

*2: AIR monitor during AIR: OFF
Time after AIR in operation 10 seconds or more
AIR pump OFF
AIR valve Close
Engine speed Less than 2800 rpm
AIR monitor during AIR: ON Completed
Time after engine start 1 second or more

P2440, P2442 (AIR valve is stuck open) (Case 2)
One of the following conditions is met (a), (b) or (c)
(a) Cumulative intake air amount 100 gm/sec or more
(b) Difference between starting temperature and current temperature 10°C (18°F) or higher
(c) Starting coolant temperature 60°C (140°F) or higher
AIR pump OFF
AIR valve Close
Engine speed Less than 4800 rpm
AIR pressure sensor fail (open/short or out of range) Not detected
Time after engine started 1 second or more
Time after AIR in operation 10 seconds or more
AIR valve open stuck Not detected
AIR pressure sensor open stuck (DTC P2445, P2447) Not in operation
Engine load 20% or more

TYPICAL MALFUNCTION THRESHOLDS

Secondary Air Injection ON (Condition 1)
Following conditions are met during AIR ON -
Cumulative pressure pulsation 10 kPa or higher
AIR pressure 2.4 kPa or higher

Secondary Air Injection ON (Condition 2)
Following conditions are met during AIR ON -
Cumulative pressure pulsation 20 kPa or higher
AIR pressure Below 2.4 kPa

Secondary Air Injection ON (Condition 3)
Following conditions are met during AIR ON -
Cumulative pressure pulsation Below 10 kPa
AIR pressure 2.4 kPa or higher

Secondary Air Injection ON (Condition 4)
Following conditions are met during AIR ON -
Cumulative pressure pulsation Below 20 kPa
AIR pressure Below 2.4 kPa

Secondary Air Injection OFF (Condition 1)
Following conditions are met during AIR OFF -
Cumulative pressure pulsation 30 kPa or higher
AIR pressure 2.4 kPa or higher

Secondary Air Injection OFF (Condition 2)
Following conditions are met during AIR OFF -
Cumulative pressure pulsation 41.25 kPa or higher
AIR pressure Below 2.4 kPa

Secondary Air Injection OFF (Condition 3)
Following conditions are met during AIR OFF -
Cumulative pressure pulsation Below 30 kPa
AIR pressure 2.4 kPa or higher

Secondary Air Injection OFF (Condition 4)
Following conditions are met during AIR OFF -
Cumulative pressure pulsation Below 41.25 kPa
AIR pressure Below 2.4 kPa

P2440, P2442 AIR valve is stuck open (Case 1)
Either condition is met: (a) or (b)
(a) AIR OFF Condition 1 Met
(b) AIR OFF Condition 2 Met

P2441, P2443 AIR valve is stuck closed
Either condition is met: (a) or (b)
(a) AIR ON Condition 3 Met
(b) AIR ON Condition 4 Met

P2440, P2442 AIR valve is stuck open (Case 2)
Cumulative pressure pulsation 100 kPa or higher

MONITOR RESULT

CONFIRMATION DRIVING PATTERN

A199319E04
0.226,1.73 1.419,1.914 1.193,0.184 10 Ignition Switch ON 0.264,2.211 1.457,2.395 1.193,0.184 10 Ignition Switch off 2.744,1.851 2.955,2.098 0.211,0.246 10 [A] 6.166,2.901 6.369,3.103 0.202,0.202 10 [B] 4.294,2.561 5.469,2.745 1.174,0.184 10 2 minutes or more 1.006,1.209 1.447,1.428 0.441,0.218 10 Idling

NOTICE:
·

This Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.

Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.

While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).

If an ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.

·

Performing the Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Air Injection Check operation finishes.



1.

Start the engine and warm it up.

2.

Turn the ignition switch off.

3.

Connect the Techstream to the DLC3.

4.

Turn the ignition switch to ON.

5.

Turn the Techstream on.

7.

Turn the ignition switch off and wait for at least 30 seconds.

8.

Turn the ignition switch to ON and turn the Techstream on [A].

9.

Enter the following menus: Powertrain / Engine and ECT / Utility / Air injection check / Automatic Mode.

10.

Start the engine after the Techstream initialization is finished.

11.

Perform the System Check operation by pressing ENTER (Next).

12.

After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the ENTER (Exit).

13.

Check pending DTCs [B].

OK:

No pending DTC is output.


14.

After the "Air injection check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

15.

Input the DTC: P2440, P2441, P2442 or P2443.

16.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



17.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If no permanent DTC is output, the system is normal.

·

If a permanent DTC is output, the system is malfunctioning.



18.

Turn the ignition switch off.


WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Determination by ECM monitoring:

The ECM locates malfunctions in the Secondary Air Injection (AIR) system by detecting the pressure in the AIR passage between the air pump and Air Switching Valve (ASV) and sets a DTC. Soon after cold engine starts, the monitor runs for a short time while the AIR system is both ON and OFF. The ECM detects both the pressure and the exhaust pulsation and compares them.

The following 8 patterns are AIR system pressure conditions in the AIR system passage.


Pressure Condition in Secondary Air Injection System Case 1:
Air Pump ON
Air Switching Valve Open
Pressure 2.4 kPa or more
Pulsation Detection Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 2:
Air Pump OFF
Air Switching Valve Open
Pressure Less than 2.4 kPa
Pulsation Detection Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 3:
Air Pump ON
Air Switching Valve Closed
Pressure 2.4 kPa or more
Pulsation Detection Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 4:
Air Pump OFF
Air Switching Valve Close
Pressure Less than 2.4 kPa
Pulsation Detection Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 5:
Air Pump ON
Air Switching Valve Open
Pressure 2.4 kPa or more
Pulsation Detection Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 6:
Air Pump OFF
Air Switching Valve Open
Pressure Less than 2.4 kPa
Pulsation Detection Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 7:
Air Pump ON
Air Switching Valve Closed
Pressure 2.4 kPa or more
Pulsation Detection Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 8:
Air Pump OFF
Air Switching Valve Close
Pressure Less than 2.4 kPa
Pulsation Detection Exhaust gas pulsation not detected

If the detected pressure is high, the air pump is assumed to be ON and if it alternates sharply, the ASV is assumed to be open. The ECM locates malfunctions from the combination of pressures detected when the AIR system is ON and OFF.

HINT:

The exhaust pulsation value is calculated in the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the AIR system.


HINT:
·

In case 3 and 7, as the pressure sensor detects a slight pump operation pulsation, the detected value is not constant. Since the pump outlet is blocked by closing the ASV, the average pressure is higher than in case 1 (approximately 20 to 30 kPa).

·

In case 1, the average pressure is approximately 3 to 11 kPa. The value of 2.4 kPa indicated in the table above is a threshold for detecting pump malfunctions.



Detected Conditions while AIR operating:
Air pump ON, ASV Open
Detected Conditions while AIR not operating:
Air pump OFF, ASV Closed
ECM Determination DTCs Output
Case 1 Case 8 Normal -
Case 1 Case 6 ASV stuck open P2440
or
P2442
Case 1 Case 7 Air pump stuck ON P2444
or
P2446
Case 2 Case 8 Air pump stuck OFF P2445
or
P2447
Case 3 Case 8 ASV stuck closed P2441
or
P2443
Case 1 Case 5 ASV stuck open and air pump stuck ON P2440 and P2444
or
P2442 and P2446
Case 2 Case 6 ASV stuck open and air pump stuck OFF P2440 and P2445
or
P2442 and P2447
Case 3 Case 7 ASV stuck closed and air pump stuck ON P2441 and P2444
or
P2443 and P2446
Case 4 Case 8 ASV stuck closed and air pump stuck OFF P2441 and P2445
or
P2443 and P2447

HINT:
·

If the vacuum hose between the ASV and the pressure sensor is not connected correctly, case 4 may occur.

·

By using the Techstream to perform the Air Injection Check operation in the System Check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions. Furthermore, Pending Codes also can be checked by performing Utility / Air Injection Check / Automatic Mode after the repair.

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



System Check:

The pressure in the secondary air passage can be checked using the Techstream.

1.

Start the engine and warm it up.

2.

Turn the ignition switch off.

3.

Connect the Techstream to the DLC3.

4.

Turn the ignition switch to ON and turn the Techstream on.

5.

Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1 CLOSE, AIR PUMP 2: OFF, ASV2 CLOSE.

HINT:

When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.


6.

Start the engine.

7.

Perform the AIR system intrusive operation while the engine is idling.

8.

Check that the air pump (AIR PUMP), ASV and pressure in the AIR system passage (PRESSURE) displayed on the Techstream indicate the conditions shown in the table below.

Standard:
Operation AIR PUMP ASV PRESSURE*1 PULSATION*2
AIR PUMP: ON, ASV: OPEN ON OPEN 2.4 kPa or more 20 kPa or more
AIR PUMP: OFF, ASV: CLOSE OFF CLOSE Less than 2.4 kPa Less than 30 kPa


*1:

Average pumping pressure (gauge pressure). The pressure should be 2.4 kPa or more when the AIR system operates.

*2:

The cumulative exhaust pulsation calculated by the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the AIR system.

9.

Turn the ignition switch to OFF.

NOTICE:
·

This Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.

Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.

While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).

If an ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.

·

Performing the Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Air Injection Check operation finishes.



HINT:
·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.





PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO SECONDARY AIR INJECTION SYSTEM DTCS)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read DTCs.

Result
Result Proceed to
P2440, P2441, P2442 and/or P2443 are output A
P2440, P2441, P2442 and/or P2443 and P0412 and/or P0415 are output B
P2440, P2441, P2442 and/or P2443 and other DTCs (except P0412 and P0415) are output C


If any DTCs other than P0412, P0415, P2440, P2441, P2442 and/or P2443 are output, troubleshoot those DTCs first.


A

2.PERFORM ACTIVE TEST USING TECHSTREAM (ACTIVATE THE AIR PUMPHEATER)

B

GO TO AIR SWITCHING VALVE INSPECTION PROCEDURE (P0412 AND P0415)

C

2.PERFORM ACTIVE TEST USING TECHSTREAM (ACTIVATE THE AIR PUMPHEATER)
a.
U153114E01
0.112,0.079 2.552,0.533 2.441,0.455 10 Front view of wire harness connector (to Air Pump Assembly) 0.41,1.428 0.733,1.570 0.323,0.142 10 D35 0.41,1.789 0.733,1.931 0.323,0.142 10 D36 0.816,1.359 0.983,1.505 0.166,0.145 10 *1 0.816,1.746 1.010,1.895 0.194,0.149 10 *2 0.301,2.683 1.193,2.845 0.892,0.163 10 *1: for Bank 1 0.301,3.018 1.193,3.181 0.892,0.163 10 *2: for Bank 2 1.603,1.518 1.22,1.054 false 0.715,0.93 1.114,1.072 0.399,0.142 10 APH+

Disconnect the air pump connector.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON and turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT/ Active Test / Activate the Air Pump Heater.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage
Tester Connection Condition Specified Condition
D35-1 (APH+) - Body ground Activate the Air Pump Heater is ON 11 to 14 V
D36-1 (APH+) - Body ground Activate the Air Pump Heater is ON 11 to 14 V


f.

Reconnect the air pump connector.



OK

3.INSPECT AIR PUMP ASSEMBLY (HEATER RESISTANCE)

NG

4.INSPECT AIR PUMP HEATER RELAY
3.INSPECT AIR PUMP ASSEMBLY (HEATER RESISTANCE)
a.

Inspect the air pump assembly (See page Engine / Hybrid System>3UR-FE EMISSION CONTROL>AIR PUMP>INSPECTION).



OK

4.INSPECT AIR PUMP HEATER RELAY

NG

4.INSPECT AIR PUMP HEATER RELAY
a.

Inspect the air pump heater relay (AI-HTR) (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION).



OK

5.CHECK AIR PUMP HEATER RELAY (POWER SOURCE)

NG

5.CHECK AIR PUMP HEATER RELAY (POWER SOURCE)
a.

Remove the air pump heater relay (AI-HTR).


b.
A258729E13
0.12,0.084 1.908,0.268 1.788,0.184 10 Engine Room Relay Block: 1.586,1.487 2.074,1.668 0.488,0.181 10 AI-HTR

Measure the voltage according to the value(s) in the table below.

Standard Voltage
Tester Connection Condition Specified Condition
AI-HTR relay terminal 3 - Body ground Always 11 to 14 V


c.

Reinstall the air pump heater relay (AI-HTR).



OK

6.CHECK HARNESS AND CONNECTOR (AIR PUMP - AIR PUMP HEATER RELAY, BODYGROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (AIR PUMP - AIR PUMP HEATER RELAY, BODYGROUND)
a.

Remove the air pump heater relay (AI-HTR).


b.

Disconnect the air pump connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance
Tester Connection Condition Specified Condition
AI-HTR relay terminal 5 - D35-1 (APH+) Always Below 1 Ω
AI-HTR relay terminal 5 - D36-1 (APH+) Always Below 1 Ω
D35-3 (APHG) - Body ground Always Below 1 Ω
D36-3 (APHG) - Body ground Always Below 1 Ω
AI-HTR relay terminal 5 or D35-1 (APH+) - Body ground Always 10 kΩ or higher
AI-HTR relay terminal 5 or D36-1 (APH+) - Body ground Always 10 kΩ or higher


d.

Reinstall the air pump heater relay (AI-HTR).


e.

Reconnect the air pump connector.



OK

7.INSPECT AIR PUMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT AIR PUMP ASSEMBLY
a.

Inspect the air pump assembly (See page Engine / Hybrid System>3UR-FE EMISSION CONTROL>AIR PUMP>INSPECTION).



OK

8.PERFORM ACTIVE TEST USING TECHSTREAM

NG

8.PERFORM ACTIVE TEST USING TECHSTREAM
A379934E01
0.115,0.083 1.094,0.469 0.979,0.385 12 true for Bank 1: 3.708,0.073 4.677,0.458 0.969,0.385 12 true for Bank 2:

a.

Visual check

i.

Start the engine and warm it up.


ii.

Turn the ignition switch off.


iii.

Disconnect the No. 1 air hose.


iv.

Connect the Techstream to the DLC3.


v.

Turn the ignition switch to ON and turn the Techstream on.


vi.

Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN.

HINT:

When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AP and ASV operation can be selected.



vii.

Start the engine.


viii.

Perform the AIR system intrusive operation while the engine is idling.


ix.

Place your hand near the air switching valve port and check that the exhaust gas pressure pulsates when the ASV is turned ON.

CAUTION:

To avoid the danger of being burned by the exhaust gas, bring your hand close to the valve port slowly.



x.

Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: ON, ASV1: CLOSE, AIR PUMP 2: ON, ASV2: CLOSE.


xi.

Check that the exhaust gas does not pulsate when the ASV is turned OFF.


xii.

Turn the ignition switch off.

NOTICE:
·

This Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.

While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).

If an ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.

·

Performing the Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Air Injection Check operation finishes.



Standard:
Air Pump Operations ASV Operations Exhaust Gas Pulsation
ON OFF Not detected
ON ON Detected




b.

Other inspection method:

The ASV operation can be confirmed by checking the cumulative pressure pulsation* provided in the System Check.

Perform System Check operation under Manual Mode.

*: The exhaust pulsation value is calculated in the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the AIR system.

i.

Start the engine and warm it up.


ii.

Turn the ignition switch off.


iii.

Connect the Techstream to the DLC3.


iv.

Turn the ignition switch to ON and turn the Techstream on.


v.

Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1: CLOSE, AIR PUMP 2: OFF, ASV2: CLOSE.


vi.

Start the engine after the Techstream initialization is finished.


vii.

Perform the AIR system intrusive operation while the engine is idling.


viii.

Check that the air-fuel ratio and pressure in the secondary air injection system passage (PULSATION) displayed on the Techstream indicate the conditions shown in the table below.


ix.

Turn the ignition switch off.



OK:
AIR System Operation Pulsation Condition
(ECM Calculation)
Air-Fuel Ratio
(Reference)
AIR PUMP: ON, ASV: OPEN 20 kPa or more 18 or more
AIR PUMP: OFF, ASV: CLOSE Less than 30 kPa Approximately 14.5
(around stoichiometric air-fuel ratio)


Reference:

If the air pump operation is confirmed as normal (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>P2444), the air-fuel ratio detected in front of three-way catalytic converter changes in response to the secondary air pumped into the exhaust port when the air pump operates.

Result
Result Proceed to
NG A
OK B


A

9.INSPECT AIR TUBE (BLOCKAGES AND LEAKAGES)

B

16.INSPECT VACUUM HOSES (AIR SWITCHING VALVE - PRESSURE SENSOR)
9.INSPECT AIR TUBE (BLOCKAGES AND LEAKAGES)
A379935E01
0.167,0.063 1.156,0.302 0.99,0.24 12 false for Bank 1: 3.76,0.073 4.75,0.313 0.99,0.24 12 false for Bank 2:

a.

Check that the No. 2 and No. 3 air tubes are securely connected to both the exhaust manifold and the ASV.


b.

Inspect the air tube for blockages and damage.

OK:

No blockages and damage on intake pipe.




OK

10.INSPECT AIR SWITCHING VALVE

NG

10.INSPECT AIR SWITCHING VALVE

OK

11.INSPECT AIR INJECTION CONTROL DRIVER (POWER SOURCE OF AIR INJECTION CONTROL DRIVER)

NG

11.INSPECT AIR INJECTION CONTROL DRIVER (POWER SOURCE OF AIR INJECTION CONTROL DRIVER)
A380322E01
0.698,1.49 1.104,1.74 0.406,0.25 0.708,3.698 1.115,3.948 0.406,0.25 3.771,1.438 4.177,1.688 0.406,0.25 3.646,3.729 4.052,3.979 0.406,0.25 1.646,1.729 1.292,2.052 true 1.604,3.875 1.25,4.198 true 4.719,1.656 4.479,2.063 true 5.406,1.646 5.635,2.094 true 4.615,3.927 4.375,4.333 true 5.448,3.917 5.729,4.365 true 0.646,0.094 2.948,0.49 2.302,0.396 10 false Front view of wire harness connector: (to AID for Bank 1) 0.74,2.438 3.042,2.833 2.302,0.396 10 false Front view of wire harness connector: (to AID for Bank 2) 4.052,0.083 6.354,0.479 2.302,0.396 10 false Front view of wire harness connector: (to AID for Bank 1) 4.083,2.427 6.385,2.823 2.302,0.396 10 false Front view of wire harness connector: (to AID for Bank 2) 0.771,1.531 1.135,1.729 0.365,0.198 10 false D31 0.781,3.74 1.146,3.938 0.365,0.198 10 false D33 3.833,1.469 4.198,1.667 0.365,0.198 10 false D32 3.729,3.771 4.094,3.969 0.365,0.198 10 false D34 0.969,2.063 1.438,2.26 0.469,0.198 10 false BATT 0.969,4.229 1.438,4.427 0.469,0.198 10 false BAT2 4.396,2.104 4.552,2.292 0.156,0.188 10 false E 5.615,2.125 5.917,2.302 0.302,0.177 10 false +B 4.24,4.344 4.573,4.583 0.333,0.24 10 false E2 5.646,4.354 6,4.531 0.354,0.177 10 false +B2

a.

Disconnect the D31 and D32 or D33 and D34 AID connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
D31-1 (BATT) - Body ground Always 11 to 14 V (near battery voltage)
D32-5 (+B) - Body ground Ignition switch ON 11 to 14 V (near battery voltage)
D33-1 (BAT2) - Body ground Always 11 to 14 V (near battery voltage)
D34-5 (+B2) - Body ground Ignition switch ON 11 to 14 V (near battery voltage)



d.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D32-1 (E) - Body ground Always Below 1 Ω
D34-1 (E2) - Body ground Always Below 1 Ω




OK

12.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)

NG

REPAIR OR REPLACE AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT

12.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)
a.

Disconnect the A27 or D56 ECM connector.


b.

Disconnect the D32 or D34 AID connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D56-28 (AIRV) - D32-3 (SIV) Always Below 1 Ω
A27-43 (ARV2) - D34-3 (SIV2) Always Below 1 Ω
D56-28 (AIRV) or D32-3 (SIV) - body ground Always 10 kΩ or higher
A27-43 (ARV2) or D34-3 (SIV2) - body ground Always 10 kΩ or higher




OK

13.PERFORM ACTIVE TEST USING TECHSTREAM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.PERFORM ACTIVE TEST USING TECHSTREAM
a.

Disconnect the D32 or D34 AID connector.

A379565E03
0.875,2.75 1.292,3.01 0.417,0.26 4.052,2.792 4.469,3.052 0.417,0.26 1.656,2.927 1.49,3.24 true 1.771,2.927 1.698,3.24 true 1.896,2.927 2.01,3.229 true 2.01,2.917 2.302,3.229 true 4.927,2.958 4.76,3.271 true 5.052,2.958 5.031,3.292 true 5.198,2.958 5.396,3.281 true 5.344,2.969 5.698,3.26 true 0.479,0.385 1.552,0.583 1.073,0.198 10 false AID (for Bank 1) 2.542,0.396 2.958,0.583 0.417,0.188 10 false ECM 1.167,1.021 1.375,1.198 0.208,0.177 10 false DI 1.104,1.344 1.365,1.521 0.26,0.177 10 false SIV 2.479,1.021 2.813,1.198 0.333,0.177 10 false AIDI 2.479,1.354 2.854,1.531 0.375,0.177 10 false AIRV 0.781,1.865 3.073,2.25 2.292,0.385 10 false Front view of wire harness connector: (to AID for Bank 1) 0.958,2.802 1.281,2.99 0.323,0.188 10 false D32 3.844,0.406 4.917,0.604 1.073,0.198 10 false AID (for Bank 2) 5.917,0.417 6.333,0.604 0.417,0.188 10 false ECM 4.406,1 4.667,1.188 0.26,0.188 10 false DI2 4.323,1.313 4.708,1.5 0.385,0.188 10 false SIV2 5.802,1 6.177,1.177 0.375,0.177 10 false AID2 5.792,1.313 6.208,1.49 0.417,0.177 10 false ARV2 1.406,3.271 1.573,3.479 0.167,0.208 10 false E 1.615,3.271 1.813,3.49 0.198,0.219 10 false DI 1.938,3.271 2.24,3.479 0.302,0.208 10 false SIV 2.281,3.26 2.583,3.469 0.302,0.208 10 false SIP 4.052,1.854 6.344,2.24 2.292,0.385 10 false Front view of wire harness connector: (to AID for Bank 2) 4.135,2.844 4.458,3.031 0.323,0.188 10 false D34 4.646,3.292 4.885,3.469 0.24,0.177 10 false E2 4.948,3.313 5.198,3.49 0.25,0.177 10 false DI2 5.302,3.313 5.646,3.49 0.344,0.177 10 false SIV2 5.74,3.26 6.083,3.438 0.344,0.177 10 false SIP2


b.

Connect terminals DI and SIV or DI2 and SIV2 of the wire harness connector for the AID.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the Techstream on.


f.

Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV 1: OPEN or AIR PUMP 2: ON, ASV 2: OPEN.

HINT:

When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



g.

Start the engine.


h.

Perform the AIR system forced operation while the engine is idling.


i.

Measure the voltage between the SIV and E or SIV2 and E2 terminals of the ECM connector when the AIR system is ON and OFF.


j.

Turn the ignition switch off.

NOTICE:
·

Performing Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Air Injection Check operation finishes.



Standard Voltage:
Tester Connection Condition Specified Condition
D32-3 (SIV) - D32-1 (E) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
D34-3 (SIV2) - D34-1 (E2) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
D32-3 (SIV) - D32-1 (E) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V
D34-3 (SIV2) - D34-1 (E2) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V



k.

Connect terminals DI and SIP or DI2 and SIP2 of the wire harness connector for the AID.

A379565E04
0.875,2.75 1.292,3.01 0.417,0.26 4.052,2.792 4.469,3.052 0.417,0.26 1.656,2.927 1.49,3.24 true 1.771,2.927 1.698,3.24 true 1.896,2.927 2.01,3.229 true 2.01,2.917 2.302,3.229 true 4.927,2.958 4.76,3.271 true 5.052,2.958 5.031,3.292 true 5.198,2.958 5.396,3.281 true 5.344,2.969 5.698,3.26 true 0.479,0.385 1.552,0.583 1.073,0.198 10 false AID (for Bank 1) 2.542,0.396 2.958,0.583 0.417,0.188 10 false ECM 1.167,1.021 1.375,1.198 0.208,0.177 10 false DI 1.104,1.344 1.365,1.521 0.26,0.177 10 false SIP 2.479,1.021 2.813,1.198 0.333,0.177 10 false AIDI 2.479,1.354 2.854,1.531 0.375,0.177 10 false AIRP 0.781,1.865 3.073,2.25 2.292,0.385 10 false Front view of wire harness connector: (to AID for Bank 1) 0.958,2.802 1.281,2.99 0.323,0.188 10 false D32 3.844,0.406 4.917,0.604 1.073,0.198 10 false AID (for Bank 2) 5.917,0.417 6.333,0.604 0.417,0.188 10 false ECM 4.406,1 4.667,1.188 0.26,0.188 10 false DI2 4.323,1.313 4.708,1.5 0.385,0.188 10 false SIP2 5.802,1 6.177,1.177 0.375,0.177 10 false AID2 5.792,1.323 6.208,1.5 0.417,0.177 10 false ARP2 1.406,3.271 1.573,3.479 0.167,0.208 10 false E 1.615,3.271 1.813,3.49 0.198,0.219 10 false DI 1.938,3.271 2.24,3.479 0.302,0.208 10 false SIV 2.281,3.26 2.583,3.469 0.302,0.208 10 false SIP 4.052,1.854 6.344,2.24 2.292,0.385 10 false Front view of wire harness connector: (to AID for Bank 2) 4.135,2.844 4.458,3.031 0.323,0.188 10 false D34 4.646,3.292 4.885,3.469 0.24,0.177 10 false E2 4.948,3.313 5.198,3.49 0.25,0.177 10 false DI2 5.302,3.313 5.646,3.49 0.344,0.177 10 false SIV2 5.74,3.26 6.083,3.438 0.344,0.177 10 false SIP2


l.

Connect the Techstream to the DLC3.


m.

Turn the ignition switch to ON.


n.

Turn the Techstream on.


o.

Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV 1: OPEN or AIR PUMP 2: ON, ASV 2: OPEN.

HINT:

When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



p.

Start the engine.


q.

Perform the AIR system forced operation while the engine is idling.


r.

Measure the voltage between the SIP and E or SIP2 and E2 terminals of the ECM connector when the AIR system is ON and OFF.


s.

Turn the ignition switch off.

NOTICE:
·

Performing Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Air Injection Check operation finishes.



Standard Voltage:
Tester Connection Condition Specified Condition
D32-4 (SIP) - D32-1 (E) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
D34-4 (SIP2) - D34-1 (E2) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
D32-4 (SIP) - D32-1 (E) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V
D34-4 (SIP2) - D34-1 (E2) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V




OK

14.REPLACE AIR INJECTION CONTROL DRIVER (BANK 1 OR BANK 2)

NG

14.REPLACE AIR INJECTION CONTROL DRIVER (BANK 1 OR BANK 2)
a.

Replace the air injection control driver (bank 1 or bank 2) (See page Engine / Hybrid System>3UR-FE EMISSION CONTROL>AIR INJECTION DRIVER>REMOVAL).



NEXT

15.CHECK WHETHER DTC OUTPUT RECURS (DTC P2440, P2441, P2442 AND/OR P2443)
15.CHECK WHETHER DTC OUTPUT RECURS (DTC P2440, P2441, P2442 AND/OR P2443)
a.

Start the engine and warm it up.


b.

Turn the ignition switch off.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON and turn the Techstream on.



f.

Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Automatic Mode.


g.

Start the engine after the Techstream initialization is finished.


h.

Perform the System Check operation by pressing Next.


i.

After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.


j.

Check pending DTCs.


k.

Turn the ignition switch off.

OK:

No pending DTC output.


NOTICE:
·

When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Air Injection Check operation finishes.





OK

END

NG

REPLACE ECM

16.INSPECT VACUUM HOSES (AIR SWITCHING VALVE - PRESSURE SENSOR)
OK:

No blockage and no deformation in vacuum hose.



OK

17.INSPECT AIR SWITCHING VALVE (PRESSURE SENSOR)

NG

REPAIR OR REPLACE VACUUM HOSE