Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM › 2015.08–2016.10
RM27L0U _51 Engine / Hybrid System _049294 3UR-FE ENGINE CONTROL _0235547 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P219A  Bank 1 Air-Fuel Ratio Imbalance  P219B  Bank 2 Air-Fuel Ratio Imbalance  P219C  Cylinder 1 Air-Fuel Ratio Imbalance  P219D  Cylinder 2 Air-Fuel Ratio Imbalance  P219E  Cylinder 3 Air-Fuel Ratio Imbalance  P219F  Cylinder 4 Air-Fuel Ratio Imbalance  P21A0  Cylinder 5 Air-Fuel Ratio Imbalance  P21A1  Cylinder 6 Air-Fuel Ratio Imbalance  P21A2  Cylinder 7 Air-Fuel Ratio Imbalance  P21A3  Cylinder 8 Air-Fuel Ratio Imbalance  


DESCRIPTION

Refer to DTC P0300 (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>P0300).

Refer to DTC P2195 (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>P2195).

DTC No. DTC Detection Condition Trouble Area
P219A The difference in air-fuel ratios between the cylinders exceeds the threshold.
·

Fuel injector assembly

·

Air induction system

·

Gas leak from exhaust system

·

Ignition system

·

Compression pressure

·

Air fuel ratio sensor

·

ECM


P219B The difference in air-fuel ratios between the cylinders exceeds the threshold.
P219C The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
P219D The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
P219E The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
P219F The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
P21A0 The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
P21A1 The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
P21A2 The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
P21A3 The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).

MONITOR DESCRIPTION

Fuel System Air-fuel Ratio Cylinder Imbalance Monitor

The ECM uses the air fuel ratio sensor and crankshaft position sensor to monitor the difference in air-fuel ratios between the cylinders caused by differences in injection volumes between the cylinders, leakage in the intake or exhaust system, etc.

When the air-fuel ratios of the cylinders are lean or rich with respect to each other, the ECM determines that a problem is present and stores a DTC.


Air Fuel Ratio Sensor Monitoring Method: P219A and/or P219B are stored primarily when a rich side imbalance is detected.

When the system detects a difference in air-fuel ratios between the cylinders due to fluctuation in the air fuel ratio sensor output over 1 engine cycle (2 crankshaft revolutions), the system determines that there is a problem.


Crankshaft Position Sensor Monitoring Method: P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 and/or P21A3 are stored primarily when a lean side imbalance is detected.

The system monitors the engine speed variation and when the variation becomes large, the system determines that there is a difference in air-fuel ratios between the cylinders, which it determines to be a problem.


MONITOR STRATEGY

Related DTCs P219A: Air fuel ratio cylinder imbalance monitor (Bank 1)
P219B: Air fuel ratio cylinder imbalance monitor (Bank 2)
P219C: Air fuel ratio cylinder imbalance monitor (Cylinder 1)
P219D: Air fuel ratio cylinder imbalance monitor (Cylinder 2)
P219E: Air fuel ratio cylinder imbalance monitor (Cylinder 3)
P219F: Air fuel ratio cylinder imbalance monitor (Cylinder 4)
P21A0: Air fuel ratio cylinder imbalance monitor (Cylinder 5)
P21A1: Air fuel ratio cylinder imbalance monitor (Cylinder 6)
P21A2: Air fuel ratio cylinder imbalance monitor (Cylinder 7)
P21A3: Air fuel ratio cylinder imbalance monitor (Cylinder 8)
Required Sensors/Components (Main) Air fuel ratio sensor
Crankshaft position sensor
Required Sensors/Components (Related) Mass air flow meter assembly
Engine coolant temperature sensor
Vehicle speed sensor
Frequency of Operation Once per driving cycle
Duration 10 seconds: Air fuel ratio sensor open circuit between AF+ and AF- and low impedance
30 seconds: Crankshaft position sensor monitoring method
MIL Operation 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

All
Monitor runs whenever following DTCs not stored P0010, P0020 (Camshaft timing oil control valve assembly bank 1, 2)
P0011, P0021 (VVT system bank 1, 2 - advance)
P0012, P0022 (VVT system bank 1, 2 - retard)
P0013, P0023 (Exhaust camshaft timing oil control valve assembly bank 1, 2)
P0014, P0024 (Exhaust VVT system bank 1, 2 - advance)
P0015, P0025 (Exhaust VVT system bank 1, 2 - retard)
P0016, P0018 (VVT system bank 1, 2 - misalignment)
P0017, P0019 (Exhaust VVT system bank 1, 2 - misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P0351, P0352, P0353, P0354, P0355, P0356 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P1340 (Camshaft position sensor)
P2440 - P2447 (Secondary air injection system)
P0500 (Vehicle speed sensor)

P219A, P219B: Air Fuel Ratio Sensor Monitoring Method
Air fuel ratio sensor status Activated
Engine speed 1400 to 2200 rpm
Engine coolant temperature 75°C (167°F) or higher
Atmospheric pressure 76 kPa (570 mmHg) or higher
Fuel system status Closed loop

P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2, P21A3: Crankshaft Position Sensor Monitoring Method
Vehicle speed Less than 3 km/h (1.875 mph)
Engine speed 400 to 1050 rpm
Engine coolant temperature 75°C (167°F) or higher
Air fuel ratio sensor status Activated
Battery voltage 11 V or higher
Fuel system status Closed loop

TYPICAL MALFUNCTION THRESHOLDS

P219A: Air Fuel Ratio Sensor Monitoring Method (Bank 1)
A/F sensor monitoring method criteria 0.196 or more

P219B: Air Fuel Ratio Sensor Monitoring Method (Bank 2)
A/F sensor monitoring method criteria 0.22 or more

P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2, P21A3: Crankshaft Position Sensor Monitoring Method
Crankshaft position sensor monitoring method criteria (lean side imbalance) 1.0 or more

MONITOR RESULT

Refer to detailed information in Checking Monitor Status (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>CHECKING MONITOR STATUS).

CONFIRMATION DRIVING PATTERN

A240420E01
0.19,0.234 1.110,0.397 0.920,0.163 10 Vehicle Speed 0.516,1.213 1.123,1.535 0.607,0.323 10 60 km/h (38 mph) 0.516,1.61 1.123,1.932 0.607,0.323 10 30 km/h (19 mph) 0.747,2.136 1.118,2.327 0.371,0.191 10 Idling 1.539,2.027 1.736,2.205 0.198,0.178 10 [A] 3.818,2.027 4.015,2.205 0.198,0.178 10 [C] 6.499,2.027 6.697,2.205 0.198,0.178 10 [J] 4.608,1.761 4.806,1.939 0.198,0.178 10 [E] 5.079,1.761 5.319,1.939 0.239,0.178 10 [G] 4.834,1.04 5.032,1.219 0.198,0.178 10 [F] 5.335,1.04 5.533,1.219 0.198,0.178 10 [H] 5.868,1.426 6.017,1.605 0.149,0.178 10 [I] 4.261,3.14 4.458,3.318 0.198,0.178 10 [D] 6.707,3.14 6.904,3.318 0.198,0.178 10 [K] 2.702,1.026 2.899,1.205 0.198,0.178 10 [B] 1.301,3.29 2.452,3.448 1.151,0.158 10 2 minutes or more 2.468,3.372 2.59,3.372 2.59,3.372 2.79,2.629 false 2.59,3.372 3.916,2.632 false 5.167,3.29 6.251,3.448 1.083,0.158 10 1 minute or more 6.266,3.372 6.388,3.372 6.388,3.372 6.589,2.629 false

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the Techstream on.

4.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

HINT:

The A/C switch and all accessory switches should be off and the shift lever should be in P or N.


5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

6.

Drive the vehicle at 60 km/h (38 mph) or higher for 2 minutes or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

It is acceptable to turn electrical loads on while driving.


7.

Idle the engine for 2 minutes or more [C].

HINT:

The A/C switch and all accessory switches should be off and the shift lever should be in P or N.


8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Drive the vehicle at less than 30 km/h (19 mph) for 5 seconds or more [E].

11.

Accelerate the vehicle from 30 to 60 km/h (19 to 38 mph) over a period of approximately 10 to 20 seconds.

HINT:

Refer to the values of mass air flow and engine speed in Typical Enabling Conditions before accelerating the vehicle from 30 to 60 km/h (19 to 38 mph).


12.

Drive the vehicle at 60 km/h (38 mph) or higher for 5 seconds or more [F].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


13.

Drive the vehicle at less than 30 km/h (19 mph) for 5 seconds or more [G].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


14.

Accelerate the vehicle from 30 to 60 km/h (19 to 38 mph) over a period of approximately 10 to 20 seconds.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Refer to the values of mass air flow and engine speed in Typical Enabling Conditions before accelerating the vehicle from 30 to 60 km/h (19 to 38 mph).


15.

Drive the vehicle at 60 km/h (38 mph) or more for 5 seconds or more [H].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


16.

Repeat steps [G] through [H] above at least 2 times [I].

17.

Idle the engine for 1 minute or more [J].

HINT:

The A/C switch and all accessory switches should be off and the shift lever should be in P or N.


18.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [K].

19.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



20.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

21.

Input the DTC: P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 or P21A3.

22.

Check the DTC judgment result.

Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the following procedure.



23.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.


·

Sensor 1 refers to the sensor closest to the engine assembly.

·

When any air-fuel ratio imbalance is detected, the ECM will perform air-fuel ratio feedback control to make the air-fuel ratio close to the stoichiometric level. This may result in an air-fuel ratio imbalance of normal cylinders and DTCs may be stored.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 and/or P21A3 are output A
DTC P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 and/or P21A3 and other DTCs are output B

HINT:

If any DTCs other than DTC P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 and/or P21A3 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING TECHSTREAM (FREEZE FRAME DATA)

B

2.READ VALUE USING TECHSTREAM (FREEZE FRAME DATA)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the Techstream, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

Freeze Frame Data Items for DTC P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 or P21A3
·

Vehicle Speed

·

Engine Speed

·

Calculate Load

·

Accelerator Idle Position

·

Short FT #1 or #2

·

Long FT #1 or #2

·

Cylinder #1 Misfire Count to Cylinder #8 Misfire Count


HINT:

When the sum of Short FT and Long FT is positive, the engine is running lean, and when the sum is negative, the engine is running rich.


Air Fuel Ratio Sensor Monitoring Method (P219A and P219B)) Crankshaft Position Sensor Monitoring Method (P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 and P21A3) Note
DTCs are output DTC is output (Only one DTC relating to a single cylinder is output) Malfunction of cylinders detected by the Crankshaft Position Sensor Monitoring Method is primarily suspected.
DTCs are output DTCs are output (Multiple DTCs relating to multiple cylinders are output) Malfunction of cylinders except ones detected by the Crankshaft Position Sensor Monitoring Method is primarily suspected.*1
DTCs are not output DTCs are output Malfunction of cylinders detected by the Crankshaft Position Sensor Monitoring Method is primarily suspected.
DTCs are output DTCs are not output Malfunctioning of the bank detected by the Air Fuel Ratio Sensor Monitoring Method is primarily suspected.

*1: When any air-fuel ratio imbalance is detected, the ECM will perform air-fuel ratio feedback control to make the air-fuel ratio close to the stoichiometric level. This may result in an air-fuel ratio imbalance of normal cylinders and DTCs may be stored.



NEXT

3.READ VALUE USING DTC OUTPUT
3.READ VALUE USING DTC OUTPUT
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

HINT:
·

If any misfire count ("Cylinder #1 Misfire Count" to "Cylinder #8 Misfire Count) increases while idling or driving the vehicle, proceed to step 6.

·

Perform inspections while focusing on the cylinder whose misfire count has increased.




e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Result
Result Proceed to
DTC P219A or P219B is output A
DTC P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 or P21A3 are output B
DTC P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 and/or P21A3 are output



A

4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME)

B

6.CHECK AIR INDUCTION SYSTEM
4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME)
a.

Connect the Techstream to the DLC3.


b.

Start the engine.


c.

Turn the Techstream on.


d.

Warm up the engine.

HINT:

The A/C switch and all accessory switches should be off and the shift lever should be in P or N.



e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / Data List / Cylinder #1 to #8 Misfire Count.

HINT:

When the "Control the Injection Volume" Active Test is selected (injection volume is 0%), if a misfire count increases, proceed to step 6 (Check Air Induction System).



f.

Perform the Control the Injection Volume operation with the engine idling.


g.

Check the misfire counts ("Cylinder #1 Misfire Count" to "Cylinder #8 Misfire Count") while decreasing the injection volume in 5% increments.

NOTICE:

Do not decrease the injection volume by more than 20%.


Result:

The cylinder whose misfire count has not increased can be assumed to be running rich. Therefore, perform inspections while focusing on that cylinder.




NEXT

5.CHECK FOR EXHAUST GAS LEAK
5.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

6.CHECK AIR INDUCTION SYSTEM

NG

REPAIR OR REPLACE EXHAUST SYSTEM

6.CHECK AIR INDUCTION SYSTEM
a.

Check the air induction system for vacuum leakage (See page Engine / Hybrid System>3UR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leakage in air induction system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the air induction system (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

7.INSPECT SPARK PLUG

NG

REPAIR OR REPLACE AIR INDUCTION SYSTEM

7.INSPECT SPARK PLUG
a.

Inspect the spark plug of the cylinder causing the imbalance (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the spark plug (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

8.CHECK FOR SPARKS AND IGNITION

NG

8.CHECK FOR SPARKS AND IGNITION
a.

Perform a spark test (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION).

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

Perform "Inspection After Repair" after replacing the spark plug or ignition coil assembly (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).





NEXT

9.CHECK CYLINDER COMPRESSION PRESSURE
9.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder (See page Engine / Hybrid System>3UR-FE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION).

HINT:

Perform "Inspection After Repair" after repairing or replacing the engine assembly (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

10.CHECK FUEL INJECTOR ASSEMBLY OF CYLINDER CAUSING IMBALANCE

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

10.CHECK FUEL INJECTOR ASSEMBLY OF CYLINDER CAUSING IMBALANCE
a.

Check the fuel injector injection [whether fuel volume is high or low, and whether injection pattern is poor] (See page Engine / Hybrid System>3UR-FE FUEL>FUEL INJECTOR>INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

11.CHECK FOR CAUSE OF FAILURE

NG

REPLACE FUEL INJECTOR ASSEMBLY

11.CHECK FOR CAUSE OF FAILURE
a.

If the cause of the problem has not been found even after performing the troubleshooting procedure, perform the inspection below.


b.

Check the intake valve for deposits.

HINT:

As the DTC may have been stored due to deposits on the intake valve, remove the cylinder head and check the intake valve.




NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the Techstream on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Check for DTCs.

Result:

P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 and/or P21A3 is not output.




NEXT

END