Home › Engine / Hybrid System › 3UR-FBE ENGINE MECHANICAL › ENGINE UNIT
RM27L0U _51 Engine / Hybrid System _049295 3UR-FBE ENGINE MECHANICAL _0235555 ENGINE UNIT A

3UR-FBE ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 12108 7.REMOVE OIL FILLER CAP SUB-ASSEMBLY

Hide 12185 8.REMOVE OIL FILLER CAP HOUSING

a.
A161903

Remove the 2 bolts, filler cap housing and gasket.


Hide 19100P 9.REMOVE SPARK PLUG

Hide 11102A 10.REMOVE VVT SENSOR (for Bank 1)

a.
A161904

Remove the 2 bolts and 2 VVT sensors.


Hide 11102A 11.REMOVE VVT SENSOR (for Bank 2)

a.
A161905

Remove the 2 bolts and 2 VVT sensors.


Hide 11102A 12.REMOVE CAMSHAFT POSITION SENSOR

a.
A161906

Remove the bolt and camshaft position sensor.


Hide 19312 13.REMOVE CRANK POSITION SENSOR PROTECTOR

A161907

a.

Remove the 2 bolts and sensor protector.


Hide 11401G 14.REMOVE CRANKSHAFT POSITION SENSOR

a.
A161908

Remove the bolt and crankshaft position sensor.


Hide 15340 15.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY LH

a.
A161909

Remove the 2 bolts and 2 oil control valves.


Hide 15330B 16.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY RH

a.
A161910

Remove the 2 bolts and 2 oil control valves.


Hide 11202 17.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 11201 18.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 15678E 19.REMOVE OIL CONTROL VALVE FILTER LH

a.
A164313E05
2.49,0.885 2.49,1.302 false 2.792,0.115 2.948,0.115 2.948,0.115 3.104,0.896 true 1.708,0.406 2.167,0.406 2.167,0.406 2.813,0.781 true 2.313,1.344 2.708,1.583 0.396,0.24 10 false Filter 1.219,0.323 1.813,0.51 0.594,0.188 10 true Gasket 1.063,0.031 2.917,0.24 1.854,0.208 10 true Cylinder Head Cover Spacer

Remove the 3 bolts, cylinder head cover spacer, gasket and valve filter.


Hide 15678D 20.REMOVE OIL CONTROL VALVE FILTER RH

a.
A164314E05
0.917,0.781 0.917,1.208 false 0.281,0.781 0.635,0.104 0.635,0.104 0.771,0.104 true 0.625,0.677 0.99,0.396 0.99,0.396 1.917,0.396 true 0.75,1.229 1.125,1.438 0.375,0.208 10 false Filter 1.958,0.292 2.458,0.5 0.5,0.208 10 true Gasket 0.802,0 2.656,0.292 1.854,0.292 10 true Cylinder Head Cover Spacer

Remove the 3 bolts, cylinder head cover spacer, gasket and valve filter.


Hide 11193 21.REMOVE SPARK PLUG TUBE GASKET

U151527E02
1.563,0.375 1.729,0.375 1.729,0.375 1.927,1.219 true 2.167,1.292 2.458,1.625 0.292,0.333 10 true Pry 1.167,0.271 1.646,0.719 0.479,0.448 10 true Tape

a.

Bend the 4 ventilation baffle plate claws on the cylinder head cover to an angle of 90° or more.


b.

Using a screwdriver, pry out the gaskets.

HINT:
·

Be careful not to damage the gasket when removing it, as the removed gasket needs to be used when installing a new one.

·

Tape the screwdriver tip before use.



NOTICE:

Be careful not to damage the cylinder head cover.



Hide 16100 22.REMOVE ENGINE WATER PUMP ASSEMBLY

Hide 11302 23.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 11301C 25.REMOVE TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL

a.

Place the timing chain cover on wooden blocks.


b.
A183314E04
1.521,0.688 1.917,0.156 1.917,0.156 2.063,0.156 true 1.01,0.854 2.25,2.052 false 0.76,0.854 1.01,0.854 1.01,0.854 1.563,1.083 false 1.021,0.854 1.188,2.052 false 2.094,0.063 3.094,0.24 1,0.177 10 true Protective Tape 0.094,0.76 0.635,1.083 0.542,0.323 10 true Wooden Block

Place the oil pump on a wooden block.


c.

Using a screwdriver and wooden block, pry out the oil seal.

HINT:

Tape the screwdriver tip before use.


NOTICE:

Do not damage the surface of the oil seal press fit hole.



Hide 26.SET NO. 1 CYLINDER TO TDC / COMPRESSION

Hide 13540 27.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY (for LH Side)

Hide 13559 28.REMOVE CHAIN TENSIONER SLIPPER (for LH Side)

Hide 13561 29.REMOVE NO. 1 CHAIN VIBRATION DAMPER (for LH Side)

Hide 13506 30.REMOVE CHAIN SUB-ASSEMBLY (for LH Side)

Hide 13560A 31.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

Hide 13540 32.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY (for RH Side)

Hide 13559 33.REMOVE CHAIN TENSIONER SLIPPER (for RH Side)

Hide 13561 34.REMOVE NO. 1 CHAIN VIBRATION DAMPER (for RH Side)

Hide 13506 35.REMOVE CHAIN SUB-ASSEMBLY (for RH Side)

Hide 13550 36.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

Hide 13521A 37.REMOVE CRANKSHAFT TIMING GEAR KEY

A145630

a.

Using a screwdriver, remove the 2 timing gear keys from the crankshaft.


Hide 11104A 39.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH

Hide 11103C 41.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH

Hide 13801 42.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 11116 46.REMOVE NO. 2 CYLINDER HEAD GASKET

Hide 11115 48.REMOVE CYLINDER HEAD GASKET

Hide 11445 49.REMOVE CYLINDER BLOCK WATER JACKET SPACER

A161997

a.

Remove the 2 water jacket spacers from the cylinder head.

NOTICE:

Be sure to remove the water jacket spacers. If not, they may fall and become damaged when the cylinder block is inverted.



Hide 12203A 50.REMOVE VENTILATION PIPE GASKET

a.
A161915E04
0.771,0.896 1.26,0.167 1.26,0.167 1.375,0.167 false 1.406,0.073 2.542,0.542 1.135,0.469 10 true Protective Tape

Using a screwdriver, pry out the ventilation pipe gasket.

HINT:

Tape the screwdriver tip before use.



Hide 16877 51.REMOVE NO. 1 HEAT EXCHANGER COVER

a.
A161916E04
2.448,1.771 2.75,2.177 0.302,0.406 9 true Nut 0.646,1.896 0.948,2.167 0.302,0.271 9 true Nut

Remove the 12 bolts and 2 nuts.


b.
A164347

Remove the heat exchanger by prying between the heat exchanger and cylinder block with a screwdriver.

HINT:

Tape the screwdriver tip before use.



Hide 12102A 52.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

a.
A160720E02
2.885,0.531 3.156,0.708 0.271,0.177 10 false Nut 1.448,1.698 1.719,1.875 0.271,0.177 10 true Nut

Remove the 14 bolts and 2 nuts.


b.
A120816

Insert the blade of oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.

NOTICE:

Be careful not to damage the contact surfaces of the oil pans.



Hide 12101 53.REMOVE OIL PAN SUB-ASSEMBLY

a.
A160721E03
2.99,1.427 3.24,1.583 0.25,0.156 10 false Nut 1.146,0.813 1.396,0.969 0.25,0.156 10 true Nut

Remove the 14 bolts and 2 nuts.

HINT:

Be sure to clean the bolts and stud bolts, and check the threads for cracks or other damage.



b.
A160722E01
0.053,0 0.702,0.183 0.649,0.183 10 LH Side: 0.053,1.544 0.688,1.727 0.635,0.183 10 RH Side:

Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.

HINT:

Tape the screwdriver tip before use.


NOTICE:

Be careful not to damage the contact surfaces of the cylinder block and oil pan.



Hide 12121 54.REMOVE NO. 1 OIL PAN BAFFLE PLATE

a.
A160723

Remove the 7 bolts and baffle plate.


Hide 15104 55.REMOVE OIL STRAINER SUB-ASSEMBLY

a.
A160724

Remove the 2 bolts, oil strainer and O-ring.


Hide 11381 56.REMOVE ENGINE REAR OIL SEAL RETAINER

a.
A145612

Remove the 6 bolts and oil seal retainer.


b.
A380260E01
0.531,1.354 0.969,0.938 true 0.177,1.344 0.823,1.781 0.646,0.438 10 true Protective Tape

Using a screwdriver, pry out the oil seal retainer.

HINT:

Tape the screwdriver tip before use.



Hide 12109A 57.REMOVE OIL DRAIN PIPE SUB-ASSEMBLY

a.
A160728

Remove the bolt and oil drain pipe.


b.

Remove the O-ring.


Hide 11381A 58.REMOVE ENGINE REAR OIL SEAL

a.
A145614E04
2.64,0.795 3.268,1.168 0.628,0.373 10 Wooden Block 2.249,1.04 2.484,0.881 2.484,0.881 2.597,0.881 false 0.027,1.074 0.671,1.431 0.644,0.357 10 Protective Tape 1.3,1.424 1.135,1.18 1.135,1.18 0.831,1.18 false

Place the oil seal retainer on wooden blocks.


b.

Using a screwdriver and hammer, tap out the oil seal.


Hide 59.REMOVE RING PIN

NOTICE:

It is not necessary to remove the ring pin unless it is being replaced.


Hide 60.REMOVE STUD BOLT

NOTICE:

If the stud bolt is deformed or its threads are damaged, replace it.