Home › Engine / Hybrid System › 3UR-FBE LUBRICATION › OIL PUMP
RM27L0U _51 Engine / Hybrid System _049305 3UR-FBE LUBRICATION _0235624 OIL PUMP A

3UR-FBE LUBRICATION  OIL PUMP  REMOVAL  


PROCEDURE

Hide 1.DISCHARGE FUEL SYSTEM PRESSURE

Hide 16400 3.REMOVE RADIATOR ASSEMBLY

Hide 87245C 6.DISCONNECT INLET HEATER WATER HOSE C

a.
A183230

Slide the clamp and disconnect the inlet heater water hose C from the water by-pass pipe sub-assembly.


Hide 87246C 7.DISCONNECT OUTLET HEATER WATER HOSE C

a.
A183228

Slide the clamp and disconnect the outlet heater water hose C from the No. 1 water by-pass pipe.


Hide 82121 8.SEPARATE ENGINE WIRE

Hide 82122 9.SEPARATE NO. 2 ENGINE WIRE

Hide 17343 11.DISCONNECT NO. 3 AIR INJECTION SYSTEM HOSE

Hide 17342 12.DISCONNECT NO. 2 AIR INJECTION SYSTEM HOSE

Hide 88320 13.SEPARATE COOLER COMPRESSOR ASSEMBLY

a.
A163332

Remove the 2 bolts, 2 nuts and 2 stud bolts, and disconnect the cooler compressor assembly.

HINT:

It is not necessary to completely remove the cooler compressor assembly. With the hoses connected to the cooler compressor assembly, hang the cooler compressor assembly on the vehicle body with a rope.



Hide 23902 14.SEPARATE NO. 2 FUEL TUBE SUB-ASSEMBLY

a.
A165142E07
0.104,0.042 0.344,0.24 0.24,0.198 10 false *a 0.177,2.365 0.354,2.552 0.177,0.188 10 false *b

Remove the 2 bolts and separate the No. 2 fuel tube sub-assembly.

Text in Illustration
*a LH Side
*b RH Side


Hide 83520 16.REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY

Hide 11452 19.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 27020 20.REMOVE GENERATOR ASSEMBLY

Hide 16261G 21.REMOVE NO. 1 WATER BY-PASS HOSE

a.
A308519

Slide the 2 clamps and remove the No. 1 water by-pass hose from the water inlet housing and front water by-pass joint.


Hide 17303 22.SEPARATE AIR PIPE SUB-ASSEMBLY

Hide 16206 23.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A162551

Slide the 2 clamps and disconnect the No. 2 water by-pass hose and No. 3 water by-pass hose from the water by-pass pipe sub-assembly.


b.

Remove the 2 bolts and water by-pass pipe sub-assembly.


Hide 16268 24.SEPARATE NO. 1 WATER BY-PASS PIPE

a.

Remove the 2 bolts and separate the No. 1 water by-pass pipe.


Hide 25.DISCONNECT NO. 9 WATER BY-PASS HOSE

a.
A291559E04
2.177,0.115 2.292,0.115 2.292,0.115 2.417,0.479 true 1.146,0.75 1.313,0.75 1.313,0.75 1.823,1.167 true 0.917,0.677 1.115,0.875 0.198,0.198 10 true *1 1.969,0.021 2.156,0.219 0.188,0.198 10 false *2

Slide the clamp and disconnect the No. 9 water by-pass hose from the front water by-pass joint.

Text in Illustration
*1 No. 9 Water By-pass Hose
*2 No. 10 Water By-pass Hose


Hide 26.DISCONNECT NO. 10 WATER BY-PASS HOSE

a.

Slide the clamp and disconnect the No. 10 water by-pass hose from the front water by-pass joint.


Hide 16355 27.REMOVE FRONT WATER BY-PASS JOINT

a.
A291566

Slide the clamp and disconnect the No. 2 water by-pass hose from the front water by-pass joint.


b.

Remove the 4 nuts, front water by-pass joint and 2 gaskets.


Hide 17303 30.REMOVE AIR PIPE SUB-ASSEMBLY

a.
A162553

Remove the bolt, disconnect the 2 hoses, and remove the air pipe sub-assembly.


Hide 16323 31.REMOVE WATER INLET HOUSING

Hide 16603 33.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

a.
A162557

Remove the bolt and No. 1 idler pulley sub-assembly.


Hide 16211 34.REMOVE FLUID COUPLING BRACKET

a.
A162558

Remove the 4 bolts and fluid coupling bracket.


Hide 16620 35.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

a.
A162527

Remove the standard bolt, 6 mm hexagon wrench bolt and V-ribbed belt tensioner assembly.


Hide 11202 37.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.
A162523

Remove the 14 bolts, seal washer, cylinder head cover sub-assembly LH and gasket.

HINT:

Make sure that the removed parts are returned to the same places they were removed from.



b.
A162524

Remove the 5 O-rings from the No. 2 camshaft bearing cap and No. 3 camshaft bearing cap.


Hide 11201 38.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A162525

Remove the 14 bolts, seal washer, cylinder head cover sub-assembly and gasket.

HINT:

Make sure that the removed parts are returned to the same places they were removed from.



b.
A162526

Remove the 5 O-rings from the No. 1 camshaft bearing cap and No. 3 camshaft bearing cap.


Hide 40.DISCONNECT WIRE HARNESS CLAMP BRACKET

a.
A163733

Remove the bolt and disconnect the wire harness clamp bracket.


Hide 13521A 41.REMOVE CRANKSHAFT TIMING GEAR KEY

a.
A163993

Using a screwdriver, remove the crankshaft timing gear key from the crankshaft.


Hide 11302 42.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

a.
A162529E02
1.826,0.549 2.068,0.719 0.242,0.170 10 *1

Remove the 28 bolts and nut shown in the illustration.

Text in Illustration
*1 Nut


b.
A162530

Remove the timing chain cover sub-assembly by prying between it and the cylinder head and cylinder block with a screwdriver as shown in the illustration.

HINT:

Tape the screwdriver tip before use.


NOTICE:

Be careful not to damage the cylinder head and cylinder block contact surfaces of the timing chain cover sub-assembly.



c.
A162531

Remove the oil pump gasket from the cylinder block.


d.
A164415

Remove the O-ring from the oil pan sub-assembly.


Hide 16322 43.REMOVE WATER INLET PIPE

a.
A162532

Remove the water inlet pipe from the No. 1 heat exchanger cover.


b.

Remove the 2 O-rings from the water inlet pipe.