Home › Engine / Hybrid System › 3UR-FE INTAKE / EXHAUST › EXHAUST PIPE
RM27L0U _51 Engine / Hybrid System _049301 3UR-FE INTAKE / EXHAUST _0235605 EXHAUST PIPE A

3UR-FE INTAKE / EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 18435A 1.INSTALL MONOLITHIC CONVERTER PROTECTOR (for Bank 1)

A184935E05
1.781,2.427 2.188,2.604 0.406,0.177 10 false Upper 0.354,3.479 0.896,3.646 0.542,0.167 10 false LH Side 2.438,3.865 3.292,4.094 0.854,0.229 10 false 20.3°+/-4°

a.

Install the 2 LH converter protector stays and 2 No. 2 converter protector stays.


b.

Install the 2 monolithic converter protectors with the 4 bolts and 4 nuts.

Torque:
11 N*m (107 kgf*cm, 8 ft.*lbf)

HINT:

Install the monolithic converter protector within the angle range shown in the illustration.



Hide 18436 2.INSTALL NO. 1 MONOLITHIC CONVERTER PROTECTOR (for Bank 1)

A184937E01
1.887,2.4 2.308,2.570 0.421,0.170 10 Upper 0.365,3.519 0.898,3.682 0.533,0.163 10 LH Side 2.398,2.987 3.261,3.160 0.864,0.173 10 49.5°+/-4°

a.

Install the 2 No. 2 converter protector stays and 2 No. 3 converter protector stays.


b.

Install the 2 No. 1 monolithic converter protectors with the 4 bolts and 4 nuts.

Torque:
11 N*m (107 kgf*cm, 8 ft.*lbf)

HINT:

Install the monolithic converter protector within the angle range shown in the illustration.



Hide 18435A 3.INSTALL MONOLITHIC CONVERTER PROTECTOR (for Bank 2)

A184931E01
1.8,2.397 2.221,2.561 0.421,0.164 10 Upper 0.374,3.585 0.901,3.751 0.527,0.166 10 LH Side 2.396,2.934 3.174,3.106 0.778,0.172 10 1.4°+/-4°

a.

Install the 2 LH converter protector stays and 2 No. 2 converter protector stays.


b.

Install the 2 monolithic converter protectors with 4 bolts and 4 nuts.

Install the 2 No. 1 monolithic converter protectors with the 4 bolts and 4 nuts.

Torque:
11 N*m (107 kgf*cm, 8 ft.*lbf)

HINT:

Install the monolithic converter protector within the angle range shown in the illustration.



Hide 18436 4.INSTALL NO. 1 MONOLITHIC CONVERTER PROTECTOR (for Bank 2)

A184933E01
1.813,2.353 2.279,2.532 0.466,0.179 10 Upper 0.363,3.449 0.914,3.621 0.551,0.172 10 LH Side 2.419,2.944 3.281,3.121 0.862,0.177 10 37.7°+/-4°

a.

Install the 2 No. 2 converter protector stays and 2 No. 3 converter protector stays.


b.

Install the 2 No. 1 monolithic converter protectors with 4 bolts and 4 nuts.

Torque:
11 N*m (107 kgf*cm, 8 ft.*lbf)

HINT:

Install the monolithic converter protector within the angle range shown in the illustration.



Hide 89467B 5.INSTALL AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)

Hide 89467B 6.INSTALL AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)

Hide 17410 7.INSTALL FRONT EXHAUST PIPE ASSEMBLY

A184929

a.

Install a new gasket and the front exhaust pipe to the exhaust manifold RH with 3 new nuts.

Torque:
54 N*m (554 kgf*cm, 40 ft.*lbf)


b.

Connect the air fuel ratio sensor connector.


Hide 17450B 8.INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY

A184928

a.

Install a new gasket and the front No. 2 exhaust pipe to the exhaust manifold LH with 3 new nuts.

Torque:
54 N*m (554 kgf*cm, 40 ft.*lbf)


b.

Connect the air fuel ratio sensor connector.


c.
A184927

Connect the front No. 3 exhaust pipe to the exhaust pipe support.


d.

Install a new gasket and the front No. 3 exhaust pipe sub-assembly to the No. 2 exhaust pipe sub-assembly with the 2 bolts and 2 new nuts.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)


Hide 89465 9.INSTALL HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)

Hide 89465 10.INSTALL HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)

Hide 17420 11.INSTALL CENTER EXHAUST PIPE ASSEMBLY

A184926

a.

Connect the center exhaust pipe to the 3 exhaust pipe supports.


b.

Install 2 new gaskets to the front exhaust pipe.


c.

Install the center exhaust pipe with the 4 bolts.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)


Hide 17430 12.INSTALL TAILPIPE ASSEMBLY

a.

Connect the tailpipe to the exhaust pipe support.


b.
A184938E01
0.514,1.646 0.929,1.804 0.415,0.158 10 Upper 0.228,2.721 0.745,2.900 0.517,0.179 10 LH Side 1.879,2.606 2.665,2.775 0.786,0.169 10 Within 30°

Install a new gasket to the center exhaust pipe.


c.

Connect the tailpipe to the center exhaust pipe.


d.

Attach a new clamp to the tailpipe and center exhaust pipe. Then install the bolt to the clamp.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)

HINT:

Install the clamp within the angle range shown in the illustration.