Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM
RM27L0U _51 Engine / Hybrid System _049309 CRUISE CONTROL _0235639 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  Cruise Control Switch Circuit  


DESCRIPTION

The cruise control main switch operates 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP, and CANCEL. The SET, TAP-DOWN, and - (COAST) functions, and the RES (RESUME), TAP-UP, and + (ACCEL) functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while operating it in the direction of each arrow and turns off after releasing it. The internal contact point of the cruise control main switch is turned on with the switch operation. Then the ECM reads the voltage value that has been changed by the switch operation to control SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL.

WIRING DIAGRAM

E152497E10
6.282,0.658 6.632,0.828 0.350,0.170 10 CCS 6.401,4.952 6.751,5.122 0.350,0.170 10 ECM 5.905,0.656 6.184,0.819 0.278,0.163 10 A27 5.945,0.416 6.118,0.579 0.173,0.163 10 45 4.357,0.653 4.642,0.815 0.284,0.163 10 H54 4.362,1.21 4.636,1.372 0.274,0.163 10 H54 4.439,0.987 4.559,1.150 0.119,0.163 10 2 4.432,0.427 4.536,0.590 0.104,0.163 10 1 3.946,0.56 4.272,0.709 0.326,0.149 10 CCS 3.946,1.127 4.272,1.276 0.326,0.149 10 ECC 3.467,1.215 3.753,1.357 0.287,0.142 10 z11 3.52,0.43 3.624,0.593 0.104,0.163 10 3 3.522,0.991 3.626,1.154 0.104,0.163 10 4 4.472,4.185 4.597,4.327 0.125,0.142 10 A 4.464,3.277 4.588,3.419 0.125,0.142 10 A 4.463,3.94 4.567,4.103 0.104,0.163 10 1 4.456,3.055 4.560,3.218 0.104,0.163 10 3 3.955,4.093 4.281,4.242 0.326,0.149 10 ECC 3.955,3.199 4.281,3.348 0.326,0.149 10 CCS 3.568,3.745 4.141,3.891 0.573,0.147 10 ON-OFF 2.611,3.731 3.137,3.905 0.526,0.174 10 + (RES) 1.672,3.731 2.199,3.905 0.526,0.174 10 - (SET) 0.724,3.745 1.325,3.891 0.600,0.147 10 CANCEL 1.476,4.672 3.183,4.846 1.707,0.174 10 Cruise Control Main Switch 3.624,1.66 4.429,1.834 0.804,0.174 10 Spiral Cable 3.467,0.662 3.730,0.804 0.264,0.142 10 z11 6.277,4.193 6.498,4.363 0.221,0.170 10 E1 5.888,4.191 6.185,4.354 0.297,0.163 10 D56 5.94,3.952 6.113,4.114 0.173,0.163 10 81

PROCEDURE

1.READ VALUE USING TECHSTREAM (CRUISE CONTROL MAIN SWITCH)
a.
E107091E05
2.127,0 3.148,0.365 1.021,0.365 10 + (ACCEL)/RES (RESUME) 2.494,0.891 3.178,1.093 0.684,0.202 10 ON/OFF 1.969,1.64 3.049,1.842 1.080,0.202 10 - (COAST)/SET 0.46,1.08 1.065,1.282 0.605,0.202 10 CANCEL

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Cruise Control / Data List.


e.

Check the Data List for proper functioning of the cruise control main switch.

ECM (Cruise Control)
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Main SW M-CPU Main switch signal (Main CPU) / ON or OFF ON: Main switch on
OFF: Main switch off
-
Cancel Switch CANCEL switch signal / ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
SET/COAST Switch -/SET switch signal / ON or OFF ON: -/SET switch on
OFF: -/SET switch off
-
RES/ACC Switch +/RES switch signal / ON or OFF ON: +/RES switch on
OFF: +/RES switch off
-

OK:

When the cruise control main switch is operated, the display changes as shown above.


Result
Result Proceed to
OK A
NG (All items are defective) B
NG (1 to 3 items are defective) C



A

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT CRUISE CONTROL MAIN SWITCH

C

2.INSPECT CRUISE CONTROL MAIN SWITCH
a.

Remove the cruise control main switch (See page Engine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

E337702E03
2.219,2.802 2.479,3 0.26,0.198 3.99,2.052 4.615,2.24 0.625,0.188 10 false CANCEL 6.333,1.125 6.958,1.313 0.625,0.188 10 false ON/OFF 0.104,0.083 1.802,0.656 1.698,0.573 10 false Component without harness connected: (Cruise Control Main Switch) 4.354,0.104 5.365,0.469 1.01,0.365 10 false + (ACCEL)/RES (RESUME) 5.01,2.333 7,2.531 1.99,0.198 10 false - (COAST)/SET 2.302,2.823 2.458,3.021 0.156,0.198 10 false A


Standard Resistance:
Tester Connection Switch Condition Specified Condition
A-3 (CCS) - A-1 (ECC) Neutral 10 kΩ or higher
A-3 (CCS) - A-1 (ECC) + (ACCEL)/RES (RESUME) 235 to 245 Ω
A-3 (CCS) - A-1 (ECC) - (COAST)/SET 620 to 640 Ω
A-3 (CCS) - A-1 (ECC) CANCEL 1510 to 1570 Ω
A-3 (CCS) - A-1 (ECC) Main switch on Below 1 Ω


c.

Reinstall the cruise control main switch.



OK

3.CHECK HARNESS AND CONNECTOR (CRUISE CONTROL MAIN SWITCH - SPIRAL CABLE)

NG

3.CHECK HARNESS AND CONNECTOR (CRUISE CONTROL MAIN SWITCH - SPIRAL CABLE)
a.

Disconnect the z11 connector from the spiral cable.


U153918E02
0.208,1.417 0.458,1.583 0.25,0.167 10 false z11 0.219,3.698 0.344,3.865 0.125,0.167 10 false A 0.115,0.073 2.479,0.417 2.365,0.344 10 false Front view of wire harness connector: (to Spiral Cable) 0.156,2.292 2.51,2.635 2.354,0.344 10 false Front view of wire harness connector: (to Cruise Control Main Switch)

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-3 - z11-3 Always Below 1 Ω
A-1 - z11-4 Always Below 1 Ω



c.

Reconnect the spiral cable connector.



OK

4.INSPECT SPIRAL CABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT SPIRAL CABLE
NOTICE:

The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the page shown in the brackets.


HINT:


a.

Remove the spiral cable.


E345235E01
2.74,0.135 3.063,0.344 0.323,0.208 3.979,2.344 4.302,2.552 0.323,0.208 2.948,0.813 3.219,0.646 3.219,0.646 3.313,0.646 false 2.833,0.813 2.302,0.323 2.302,0.323 2.198,0.323 false 4.042,3.146 3.927,2.656 3.927,2.656 3.844,2.656 false 4.135,3.125 4.563,2.49 4.563,2.49 4.667,2.49 false 0.052,0.052 1.26,0.615 1.208,0.563 10 false Component without harness connected: (Spiral Cable) 2.802,0.156 3.26,0.354 0.458,0.198 10 false z11 4.031,2.365 4.49,2.563 0.458,0.198 10 false H54 3.354,0.563 3.813,0.76 0.458,0.198 10 false CCS 1.896,0.25 2.354,0.448 0.458,0.198 10 false ECC 3.531,2.583 3.99,2.781 0.458,0.198 10 false CCS 4.698,2.417 5.156,2.615 0.458,0.198 10 false ECC

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Spiral Cable Position Specified Condition
z11-3 (CCS) - H54-1 (CCS) Center Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
z11-4 (ECC) - H54-2 (ECC) Center Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right


HINT:

The spiral cable makes a maximum of approximately 5 rotations.



c.

Reinstall the spiral cable.



OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM AND BODY GROUND)

NG

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM AND BODY GROUND)
a.

Disconnect the A27 connector from the ECM.

E344854E02
3.25,1.458 3.583,1.688 0.333,0.229 0.771,1.573 1.104,1.802 0.333,0.229 1.49,1.688 1.125,2.042 false 1.625,1.646 2.406,1.375 false 5.313,1.917 5.135,2.479 false 0.552,0.083 2.792,0.469 2.24,0.385 10 false Front view of wire harness connector: (to Spiral Cable) 3.677,0.073 5.948,0.469 2.271,0.396 10 false Front view of wire harness connector: (to ECM) 0.823,1.604 1.281,1.802 0.458,0.198 10 false H54 3.302,1.49 3.76,1.688 0.458,0.198 10 false A27 0.948,2.063 1.406,2.26 0.458,0.198 10 false CCS 2.469,1.292 2.927,1.49 0.458,0.198 10 false ECC 4.99,2.479 5.448,2.677 0.458,0.198 10 false CCS


b.

Disconnect the H54 connector from the spiral cable.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H54-1 (CCS) - A27-45 (CCS) Always Below 1 Ω
A27-45 (CCS) - Body ground Always 10 kΩ or higher
H54-2 (ECC) - Body ground Always Below 1 Ω



d.

Reconnect the ECM and spiral cable connector.


Result
Result Proceed to
NG A
OK (for 3UR-FE) B
OK (for 3UR-FBE) C


A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C