Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC LASER CRUISE CONTROL SYSTEM
RM27L0U _51 Engine / Hybrid System _049309 CRUISE CONTROL _0235640 DYNAMIC LASER CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC LASER CRUISE CONTROL SYSTEM  Laser Sensor Power Source Circuit  


DESCRIPTION

This circuit provides power to the laser radar sensor. The laser radar sensor emits radio waves towards an object in front and measures the distance and direction of the object by receiving the beam reflections. Based on the reflections, the sensor calculates the difference in speed between the vehicle and the object in front. This data is transmitted to the distance control ECU. The ECM recognizes the laser radar sensor via terminals LGND. If an open circuit occurs in the wire harness between terminals LGND, the ECM cannot recognize the laser radar sensor. The ECM will stop the control of the vehicle-to-vehicle distance control mode and only the constant speed control mode can be used.

WIRING DIAGRAM

E163058E01
0.74,1.791 1.071,1.939 0.332,0.148 10 ECM 0.46,1.675 0.753,1.840 0.292,0.164 10 A27 1.373,0.885 1.560,1.053 0.187,0.168 10 44 0.85,0.984 1.274,1.126 0.423,0.142 10 LGND 0.831,2.942 1.274,3.083 0.443,0.142 10 LGND 1.003,3.49 1.275,3.645 0.273,0.155 10 IGB 0.837,4.151 1.276,4.304 0.439,0.152 10 SGND 6.153,3.494 6.430,3.666 0.278,0.173 10 IGB 5.855,3.404 6.069,3.575 0.214,0.171 10 13 1.366,2.826 1.468,2.984 0.102,0.158 10 1 1.373,3.404 1.482,3.552 0.109,0.148 10 5 1.367,4.051 1.489,4.200 0.122,0.148 10 2 0.421,4.733 0.733,4.881 0.312,0.148 10 A26 5.717,4.904 6.009,5.048 0.292,0.145 10 A43 5.723,5.066 7.117,5.240 1.393,0.174 10 Distance Control ECU 0.414,4.892 1.707,5.053 1.293,0.161 10 Laser Radar Sensor

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IGB VOLTAGE)
a.
U154120E02
0.99,1.344 1.115,1.344 1.115,1.344 1.938,2.271 false 0.333,0.177 2.656,0.521 2.323,0.344 10 false Front view of wire harness connector: (to Laser radar Sensor) 0.542,2.208 0.833,2.385 0.292,0.177 10 false A26 0.615,1.26 0.875,1.417 0.26,0.156 10 false IGB

Disconnect the A26 laser radar sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A26-5 (IGB) - Body ground Ignition switch ON 11 to 14 V



c.

Reconnect the laser radar sensor connector.



OK

2.CHECK HARNESS AND CONNECTOR (LASER RADAR SENSOR - ECM AND BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (LASER RADAR SENSOR - DISTANCE CONTROL ECU)
2.CHECK HARNESS AND CONNECTOR (LASER RADAR SENSOR - ECM AND BODY GROUND)
a.

Disconnect the A27 connector from the ECM.

E345250E01
0.865,1.583 1.177,1.802 0.313,0.219 3.615,1.531 3.927,1.74 0.313,0.208 1.677,1.74 1.427,2.281 1.427,2.281 1.333,2.281 false 1.802,1.708 2.063,1.042 2.063,1.042 2.167,1.042 false 5.313,1.844 5.052,2.406 5.052,2.406 4.938,2.406 false 0.771,0.115 3.042,0.479 2.271,0.365 10 false Front view of wire harness connector: (to Laser radar Sensor) 3.938,0.135 6.208,0.5 2.271,0.365 10 false Front view of wire harness connector: (to ECM) 0.917,1.615 1.375,1.813 0.458,0.198 10 false A26 3.667,1.552 4.125,1.75 0.458,0.198 10 false A27 0.948,2.198 1.563,2.396 0.615,0.198 10 false LGND 2.219,0.958 2.833,1.156 0.615,0.198 10 false SGND 4.552,2.333 5.167,2.531 0.615,0.198 10 false LGND


b.

Disconnect the A26 connector from the laser radar sensor.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-44 (LGND) - A26-1 (LGND) Always Below 1 Ω
A26-1 (LGND) - Body ground Always 10 kΩ or higher
A26-2 (SGND) - Body ground Always Below 1 Ω



d.

Reconnect the ECM and laser radar sensor connector.



OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (LASER RADAR SENSOR - DISTANCE CONTROL ECU)
a.
E345254E01
0.552,1.323 0.885,1.552 0.333,0.229 0.073,3.323 0.406,3.552 0.333,0.229 1.969,1.406 2.542,1.302 false 0.719,3.708 0.5,4.021 false 0.542,0.042 2.833,0.438 2.292,0.396 10 false Front view of wire harness connector: (to Laser radar Sensor) 0.573,2.031 2.844,2.396 2.271,0.365 10 false Front view of wire harness connector: (to Distance Control ECU) 0.604,1.354 1.063,1.552 0.458,0.198 10 false A26 0.125,3.354 0.583,3.552 0.458,0.198 10 false A43 2.573,1.229 3.031,1.427 0.458,0.198 10 false IGB 0.24,3.958 0.698,4.156 0.458,0.198 10 false IGB

Disconnect the A43 distance control ECU connector.


b.

Disconnect the A26 laser radar sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A26-5 (IGB) - A43-13 (IGB) Always Below 1 Ω
A43-13 (IGB) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECU and laser radar sensor connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR