Home › Drivetrain › AB60F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM27L0U _52 Drivetrain _049310 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0235644 AUTOMATIC TRANSMISSION SYSTEM C

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P2716  Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)  


DESCRIPTION

Refer to DTC P0894 (See page Drivetrain>AB60F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>P0894).

DTC Code DTC Detection Condition Trouble Area
P2716 Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1 trip detection logic)
·

Open or short in shift solenoid valve SLT circuit

·

Shift solenoid valve SLT

·

ECM



MONITOR DESCRIPTION

When an open or short in the shift solenoid valve SLT circuit is detected, the ECM interprets this as a fault. The ECM will turn on the MIL and store the DTC.

MONITOR STRATEGY

Related DTCs P2716: Shift solenoid valve SLT/Range check
Required sensors/Components Shift solenoid valve SLT
Frequency of operation Continuous
Duration 1 second
MIL operation Immediately
Sequence of operation None

TYPICAL ENABLING CONDITIONS

The monitor will run whenever the following DTCs are not present None
Solenoid current cut status Not cut
Battery voltage 11 V or higher
Ignition switch ON
Starter OFF

TYPICAL MALFUNCTION THRESHOLDS

Solenoid voltage monitor signal from solenoid driver MIC No signal

COMPONENT OPERATING RANGE

Output signal duty Less than 100%

WIRING DIAGRAM

C352872E13
0.792,1.385 0.948,1.583 0.156,0.198 10 false 2 0.802,2.198 0.958,2.396 0.156,0.198 10 false 1 2.333,2.323 2.719,2.51 0.385,0.188 10 false SLT- 2.771,1.333 2.927,1.531 0.156,0.198 10 false 13 2.792,2.542 2.948,2.74 0.156,0.198 10 false 5 5.438,1.313 5.594,1.51 0.156,0.198 10 false 9 5.458,2.531 5.615,2.729 0.156,0.198 10 false 8 2.333,1.104 2.719,1.292 0.385,0.188 10 false SLT+ 1.104,1.802 2.708,2 1.604,0.198 10 false Shift Solenoid Valve SLT 5.729,1.208 6.115,1.396 0.385,0.188 10 false SLT+ 5.729,2.427 6.115,2.615 0.385,0.188 10 false SLT- 0.49,2.969 0.875,3.156 0.385,0.188 10 false D41 0.5,3.135 2.104,3.313 1.604,0.177 10 false No. 1 Transmission Wire 5.813,3.24 6.198,3.427 0.385,0.188 10 false D56 5.813,3.438 6.198,3.625 0.385,0.188 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Perform the universal trip to clear permanent DTCs (See page Drivetrain>AB60F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).


PROCEDURE

1.INSPECT NO. 1 TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT)
a.
C159421E42
1.088,2.631 1.522,2.776 0.434,0.145 10 SLT+ 0.058,0.046 2.640,0.413 2.582,0.367 10 Component without harness connected: (No. 1 Transmission Wire) 1.816,2.631 2.253,2.776 0.437,0.145 10 SLT- 1.583,2.024 1.325,2.592 false 1.651,1.804 1.956,2.592 false

Disconnect the D41 No. 1 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
13 (SLT+) - 5 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
13 (SLT+) - Body ground Always 10 kΩ or higher
5 (SLT-) - Body ground Always 10 kΩ or higher




OK

2.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SLT
2.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - ECM)
U153481E02
0.688,2.885 1.104,1.656 true 1.604,2.896 1.177,1.667 true 0.073,0.042 2.479,0.406 2.406,0.365 10 false Front view of wire harness connector: (to ECM) 1.573,1.042 1.948,1.271 0.375,0.229 10 false D56 1.292,2.906 2,3.104 0.708,0.198 10 false 9 (SLT+) 0.229,2.906 0.938,3.104 0.708,0.198 10 false 8 (SLT-)

a.

Disconnect the D56 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D56-9 (SLT+) - D56-8 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
D56-9 (SLT+) - Body ground Always 10 kΩ or higher
D56-8 (SLT-) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
NG A
OK (for 3UR-FE) B
OK (for 3UR-FBE) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C

3.INSPECT SHIFT SOLENOID VALVE SLT
a.

Remove the shift solenoid valve SLT.


C351967E04
1.125,0.99 1.531,1.25 true 2.281,1 1.885,1.25 true 2.281,2.979 1.885,3.229 true 1.125,2.969 1.531,3.229 true 0.063,0.063 2.5,0.406 2.438,0.344 10 false Component without harness connected: (Shift Solenoid Valve SLT) 1,0.906 1.104,1.104 0.104,0.198 10 false 2 2.313,0.917 2.417,1.115 0.104,0.198 10 false 1 1.01,2.865 1.115,3.063 0.104,0.198 10 false 2 2.313,2.896 2.417,3.094 0.104,0.198 10 false 1 1.271,4.344 1.49,4.542 0.219,0.198 10 false (+) 1.99,4.344 2.156,4.542 0.167,0.198 10 false (-)

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect the battery positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating noise.

OK:

Valve moves and makes an operating noise.




OK

REPAIR OR REPLACE NO. 1 TRANSMISSION WIRE

NG