Home › Drivetrain › AB60F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM27L0U _52 Drivetrain _049310 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0235644 AUTOMATIC TRANSMISSION SYSTEM C

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0985  Shift Solenoid "E" Control Circuit Low (Shift Solenoid Valve SR)  P0986  Shift Solenoid "E" Control Circuit High (Shift Solenoid Valve SR)  


DESCRIPTION

Shifting from 1st to 6th is performed in combination with ON and OFF operation of the shift solenoid valves SL1, SL2, S1, S2, S3, S4 and SR, which are controlled by the ECM. If an open or short circuit occurs in any of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated safely. Also, the ECM stops sending the current to the open or short circuited solenoid (See page Drivetrain>AB60F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>FAIL-SAFE CHART).

DTC Code DTC Detection Condition Trouble Area
P0985 ECM detects short in solenoid valve SR circuit 2 times when solenoid valve SR is operated (1 trip detection logic)
·

Short in shift solenoid valve SR circuit

·

Shift solenoid valve SR

·

ECM


P0986 ECM detects open in solenoid valve SR circuit 2 times when solenoid valve SR is not operated (1 trip detection logic)
·

Open in shift solenoid valve SR circuit

·

Shift solenoid valve SR

·

ECM



MONITOR DESCRIPTION

These DTCs indicate an open or short in the shift solenoid valve SR circuit. When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores the DTC. When the shift solenoid valve SR is ON, if its resistance is 8 Ω or less, the ECM determines there is a short in the shift solenoid valve SR circuit.

When the shift solenoid valve SR is OFF, if its resistance is 100 kΩ or more, the ECM determines there is an open in the shift solenoid valve SR circuit (See page Drivetrain>AB60F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>FAIL-SAFE CHART).

MONITOR STRATEGY

Related DTCs P0985: Shift solenoid valve SR/Range check (Low resistance)
P0986: Shift solenoid valve SR/Range check (High resistance)
Required sensors/Components Shift solenoid valve SR
Frequency of operation Continuous
Duration 0.128 seconds or more
MIL operation Immediately
Sequence of operation None

TYPICAL ENABLING CONDITIONS

All
The monitor will run whenever the following DTCs are not present None
Battery voltage 8 V or higher
Ignition switch ON
Starter OFF

P0985: Range Check (Low Resistance)
Command to shift solenoid valve SR ON

P0986: Range Check (High Resistance)
Command to shift solenoid valve SR OFF

TYPICAL MALFUNCTION THRESHOLDS

P0985: Range Check (Low Resistance)
Shift solenoid valve SR resistance 8 Ω or less

P0986: Range Check (High Resistance)
Shift solenoid valve SR resistance 100 kΩ or more

COMPONENT OPERATING RANGE

Shift solenoid valve SR resistance 11 to 15 Ω at 20°C (68°F)

WIRING DIAGRAM

C352873E12
2.479,0.875 2.708,1.063 0.229,0.188 10 false SR 5.729,1.01 5.958,1.198 0.229,0.188 10 false SR 2.792,1.115 3,1.292 0.208,0.177 10 false 6 5.448,1.115 5.677,1.302 0.229,0.188 10 false 4 1.031,1.74 2.552,1.917 1.521,0.177 10 false Shift Solenoid Valve SR 0.479,2.771 0.781,2.958 0.302,0.188 10 false D41 0.479,2.948 2,3.125 1.521,0.177 10 false No. 1 Transmission Wire 5.813,3.104 6.115,3.292 0.302,0.188 10 false D56 5.813,3.281 6.115,3.469 0.302,0.188 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Perform the universal trip to clear permanent DTCs (See page Drivetrain>AB60F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).


HINT:

The shift solenoid valve SR is turned ON/OFF normally when the shift lever is in D:

ECM gear shift command 1st 2nd 3rd 4th 5th 6th
Shift solenoid valve SR ON ON ON ON OFF OFF


PROCEDURE

1.INSPECT NO. 1 TRANSMISSION WIRE (SHIFT SOLENOID VALVE SR)
a.
C159421E41
0.058,0.046 2.640,0.413 2.582,0.367 10 Component without harness connected: (No. 1 Transmission Wire) 1.056,2.631 1.493,2.776 0.437,0.145 10 SR 1.512,1.804 1.207,2.592 false

Disconnect the D41 No. 1 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (SR) - Body ground 20°C (68°F) 11 to 15 Ω




OK

2.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SR
2.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - ECM)
U153480E02
0.375,2.896 0.75,1.667 true 0.073,0.042 2.479,0.406 2.406,0.365 10 false Front view of wire harness connector: (to ECM) 1.573,1.042 1.948,1.271 0.375,0.229 10 false D56 0.104,2.906 0.646,3.104 0.542,0.198 10 false 4 (SR)

a.

Disconnect the D56 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D56-4 (SR) - Body ground 20°C (68°F) 11 to 15 Ω


Result
Result Proceed to
NG A
OK (for 3UR-FE) B
OK (for 3UR-FBE) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C

3.INSPECT SHIFT SOLENOID VALVE SR
a.
C160565E02
2.349,0.818 2.580,1.002 0.231,0.184 10 (+) 0.056,0 1.633,0.186 1.577,0.186 10 Shift Solenoid Valve SR: 3.116,0.818 3.347,1.002 0.231,0.184 10 (-)

Remove the shift solenoid valve SR.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Shift solenoid valve SR connector terminal - Shift solenoid valve SR body 20°C (68°F) 11 to 15 Ω



c.

Connect the battery positive (+) lead to the terminal of the solenoid valve connector, and the negative (-) lead to the solenoid valve body. Then check that the valve moves and makes an operating noise.

OK:

Valve moves and makes an operating noise.




OK

REPAIR OR REPLACE NO. 1 TRANSMISSION WIRE

NG