Home › Drivetrain › AB60F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › 2015.08–2016.10
RM27L0U _52 Drivetrain _049310 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0235644 AUTOMATIC TRANSMISSION SYSTEM C

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P2772  Four Wheel Drive (4WD) Low Switch Circuit Range / Performance  


DESCRIPTION

The ECM detects the signal from the transfer 4L position switch.

This DTC indicates that the transfer 4L position switch remains on.

DTC Code DTC Detection Condition Trouble Area
P2772 Transfer 4L position switch remains ON while vehicle is running under following conditions for 1.8 sec. or more (1-trip detection logic)
(a) Output shaft speed between 1000 and 3000 rpm
(b) Transfer position switch is in 4H
·

Short in transfer 4L position switch circuit

·

4WD control ECU

·

ECM



MONITOR DESCRIPTION

The ECM monitors the transfer-case 4L position switch to determine when the transfer-case 4L gear is engaged. If the transfer-case 4L gears remain engaged under the following conditions, the ECM will conclude that there is a malfunction of the 4L position switch, illuminate the MIL and store the DTC:

·

The 4L switch indicates that the 4L transfer-case gears are engaged.

·

The transfer-case shifter is in the "4H" position.

·

The transfer-case output shaft rpm is between 1000 and 3000 rpm.

·

The specified time period has elapsed.


MONITOR STRATEGY

Related DTCs P2772: Transfer 4L position switch/Functional check
Required sensors/Components Transfer 4L position switch
Frequency of operation Continuous
Duration ON malfunction (A): 1.8 seconds
ON malfunction (B): 0.5 seconds
MIL operation 1 driving cycle
Sequence of operation None

TYPICAL ENABLING CONDITIONS

All
The monitor will run whenever the following DTCs are not present P0500 (Output speed sensor circuit)
P0722 (Vehicle speed sensor circuit)
Transfer neutral position switch OFF

ON Malfunction (A)
Output speed (Transfer output speed) 1000 rpm or more, and less than 3000 rpm

ON Malfunction (B)
Output speed (Transfer output speed) 143 rpm or more

TYPICAL MALFUNCTION THRESHOLDS

Both of the following conditions are met: ON malfunction (A) and (B)

ON Malfunction (A)
4L switch ON

ON Malfunction (B)
Actual transfer gear ratio
Transfer input speed/Transfer output speed
0.9 or more, and less than 1.1

WIRING DIAGRAM

C214970E18
1.427,2.146 2.646,2.344 1.219,0.198 10 false 4WD Control ECU 1.427,1.969 1.823,2.167 0.396,0.198 10 false A28 2.5,1.333 2.896,1.531 0.396,0.198 10 false 21 2.177,1.229 2.573,1.427 0.396,0.198 10 false L4 5.635,1.229 6.135,1.427 0.5,0.198 10 false L4 5.344,1.333 5.583,1.531 0.24,0.198 10 false 21 5.813,2.938 6.313,3.135 0.5,0.198 10 false A27 5.813,3.115 6.313,3.313 0.5,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Perform the universal trip to clear permanent DTCs (See page Drivetrain>AB60F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4WD CONTROL ECU - BODY GROUND)
a.
U153543E01
0.055,0.002 2.463,0.370 2.408,0.367 10 Front view of wire harness connector: (to 4WD Control ECU) 1.579,1.132 1.954,1.365 0.375,0.233 10 A28 0.18,2.814 0.438,3.016 0.258,0.202 10 L4 0.316,2.799 0.535,2.158 false

Disconnect the A28 4WD control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-21 (L4) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
NG A
OK B



A

2.CHECK HARNESS AND CONNECTOR (4WD CONTROL ECU - ECM)

B

2.CHECK HARNESS AND CONNECTOR (4WD CONTROL ECU - ECM)
a.
U153485E01
0.052,0.006 2.461,0.373 2.409,0.367 10 Front view of wire harness connector: (to ECM) 1.681,1.001 2.056,1.234 0.375,0.233 10 A27 0.986,2.867 1.513,3.069 0.527,0.202 10 21 (L4) 1.296,2.852 1.605,1.797 false

Disconnect the A27 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-21 (L4) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
NG A
OK (for 3UR-FE) B
OK (for 3UR-FBE) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C