Home › Drivetrain › AB60E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION ASSEMBLY
RM27L0U _52 Drivetrain _049311 AB60E AUTOMATIC TRANSMISSION / TRANSAXLE _0235666 AUTOMATIC TRANSMISSION ASSEMBLY A

AB60E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 32000 1.INSTALL TORQUE CONVERTER ASSEMBLY

U152409E01
3.138,0.306 3.292,0.499 0.154,0.193 10 A 3.126,1.351 3.319,1.530 0.193,0.179 10 *2 1.581,2.56 1.774,2.739 0.193,0.179 10 *2 2.96,0.549 3.130,0.718 0.170,0.170 10 *1 0.848,2.993 1.018,3.163 0.170,0.170 10 *1 0.629,2.636 0.722,3.078 0.722,3.078 0.823,3.078 false 1.407,2.296 1.482,2.654 1.482,2.654 1.583,2.654 false

a.

Using a vernier caliper and straightedge, measure dimension A between the transmission fitting surface of the engine *1 and the converter fitting surface of the drive plate *2. (#)


b.
C150409E04
0.75,0.5 1.438,0.146 1.438,0.146 0.813,0.76 true 1.479,0.042 2.25,0.219 0.771,0.177 10 true Matchmark

Aligning the matchmarks on the transmission case and torque converter, and then engage the splines of the input shaft and turbine runner.


c.
C150410E05
0.75,0.521 1.427,0.198 1.427,0.198 0.969,1.708 true 1.458,0.073 2.188,0.271 0.729,0.198 10 true Matchmark

Engage the splines of the stator shaft and stator while turning the torque converter.

HINT:

Turn the torque converter approximately 180°.



d.
C150411E05
0.75,0.5 1.354,0.177 1.354,0.177 0.708,1.063 true 1.406,0.073 2.146,0.26 0.74,0.188 10 true Matchmark

Turn the torque converter and align the matchmarks on the torque converter and transmission case to engage the key of the oil pump drive gear into the slot on the torque converter.

NOTICE:

Do not push on the torque converter when aligning the matchmarks.



e.
C193839E02
2.852,0.638 3.008,0.813 0.156,0.174 10 B

Using a vernier caliper and a straightedge, measure dimension B shown in the illustration and check that B is greater than A measured in the first step.

Standard distance:

B = A + 1 mm (0.0394 in.) or more



Hide 33823A 2.INSTALL TRANSMISSION CONTROL CABLE BRACKET

a.
C161368

Install the transmission control cable bracket with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 3.INSTALL CONNECTOR CLAMP BRACKET

a.

Install the front left bank oxygen sensor connector clamp bracket with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Install the rear left bank oxygen sensor connector clamp bracket with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


c.

Install the front right bank oxygen sensor connector clamp bracket with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 35000 4.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY

C196694E06
1.688,1.052 2.26,0.625 2.26,0.625 2.344,0.625 true 2.396,0.521 3.219,2.063 0.823,1.542 10 true Torque Converter Clutch Centerpiece 0.219,0.969 1.021,1.167 0.802,0.198 10 false Crankshaft

a.

Apply clutch spline grease to the surface of the torque converter centerpiece that contacts the crankshaft.

Clutch spline grease:

Toyota Genuine Clutch Spline Grease or equivalent

Maximum grease amount:

Approximately 1 g (0.0353 oz.) Centerpiece



b.
U153670E02
2.042,2.344 2.177,2.5 0.135,0.156 10 false A 2.708,2.948 2.844,3.104 0.135,0.156 10 false A 2.844,3.76 2.979,3.917 0.135,0.156 10 false A 1.385,2.354 1.521,2.51 0.135,0.156 10 false A 0.75,2.885 0.885,3.042 0.135,0.156 10 false A 0.656,3.594 0.792,3.75 0.135,0.156 10 false A 2.656,3.927 2.781,4.083 0.125,0.156 10 false B 2.188,4.354 2.313,4.51 0.125,0.156 10 false B 1.24,4.365 1.365,4.521 0.125,0.156 10 false B 0.771,3.917 0.896,4.073 0.125,0.156 10 false B

Confirm that the 2 knock pins are on the transaxle contact surface of the engine block before transaxle installation.


c.

Install the transmission with the 10 bolts.

Torque:
for 17 mm head bolt A : 71 N*m (724 kgf*cm, 52 ft.*lbf)
for 14 mm head bolt B : 37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 35104V 5.CONNECT BREATHER PLUG HOSE

a.
C163095

Connect the breather plug hose to the harness clamp bracket.


Hide 6.CONNECT WIRE HARNESS AND CONNECTOR

a.
C353008

Connect the park/neutral start switch connector, 2 transmission wire connectors and 2 speed sensor connectors.

HINT:

Push up the lever until the claw of the transmission wire connector makes a connection sound.



b.

Connect the harness clamp with the bolt.

Torque:
8.2 N*m (84 kgf*cm, 73 in.*lbf)


c.

Connect the 3 connector clamps and 4 harness clamps.


d.

Tilt up the automatic transmission.


e.
C155915

Connect the ground cable with the bolt.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 12371 7.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

a.
C161359

Install the rear No. 1 engine mounting insulator to the transmission with the 4 bolts.

Torque:
40 N*m (407 kgf*cm, 30 ft.*lbf)


Hide 51204 8.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.
C161357

Install the No. 3 frame crossmember to the rear engine mounting insulator with the 4 bolts.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


b.
C161358

Install the No. 3 frame crossmember with the 4 bolts, 4 washers and 4 nuts.

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)


Hide 32101A 9.INSTALL DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT

a.
C161354

Turn the crankshaft to gain access to the 6 bolts and install the bolts while holding the crankshaft pulley set bolt with a wrench.

Torque:
53 N*m (535 kgf*cm, 39 ft.*lbf)

HINT:

First install the black colored bolt and then the remaining 5 bolts.



Hide 28100 10.INSTALL STARTER ASSEMBLY

a.

Install the starter assembly (See page Engine / Hybrid System>3UR-FE STARTING>STARTER>INSTALLATION).


Hide 33820B 11.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
U152340E02
2.427,0.865 1.292,1.115 true 0.781,1.052 1.313,1.219 0.531,0.167 10 false Bracket 0.865,0.292 1.927,0.542 1.063,0.25 10 true Inside of Vehicle

Connect the transmission control cable with a new clip and nut.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)

NOTICE:

When connecting the cable to the transmission control shaft lever, make sure the cable's L bracket faces the outside of the vehicle.



Hide 37110 15.INSTALL PROPELLER SHAFT ASSEMBLY

Hide 17.ADD AUTOMATIC TRANSMISSION FLUID

Fluid type:

Toyota Genuine ATF WS


HINT:

Fill the transmission with the amount of fluid listed in the table below.


Standard Capacity:
Repair Fill amount
Transmission pan and drain plug removal 2.1 liters (2.2 US qts, 1.9 Imp. qts)
Transmission valve body removal 4.7 liters (5.0 US qts, 4.1 Imp. qts)
Torque converter removal 6.1 liters (6.4 US qts, 5.4 Imp. qts)


Hide 18.ADJUST AUTOMATIC TRANSMISSION FLUID

Hide 19.INSPECT FOR AUTOMATIC TRANSMISSION FLUID LEAK

Hide 21.INSPECT FOR EXHAUST GAS LEAK

Hide 24.RESET MEMORY

a.

Perform the Reset Memory procedures (A/T initialization) (See page Drivetrain>AB60E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION).