Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM27L0U _54 Brake _049321 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0235735 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C0226/21  SFR Solenoid Circuit  C0236/22  SFL Solenoid Circuit  C0246/23  SRR Solenoid Circuit  C0256/24  SRL Solenoid Circuit  C1225/25  SMC Solenoid Circuit  C1226/26  SMC Solenoid Circuit  C1227/27  SRC Solenoid Circuit  C1228/28  SRC Solenoid Circuit  


DESCRIPTION

This solenoid is turned on in accordance with signals from the skid control ECU and controls the pressure on the wheel cylinders to control the braking force.

C160048E02
3.448,6.271 4.563,6.5 1.115,0.229 10 false Skid Control ECU 3.719,1.156 4.198,1.385 0.479,0.229 10 false SMC1 3.729,1.583 4.208,1.813 0.479,0.229 10 false SMC2 3.729,2.01 4.208,2.24 0.479,0.229 10 false SRC1 3.74,2.438 4.219,2.667 0.479,0.229 10 false SRC2 3.729,2.885 4.208,3.115 0.479,0.229 10 false SFRH 3.729,3.313 4.208,3.542 0.479,0.229 10 false SFRR 3.719,3.76 4.198,3.99 0.479,0.229 10 false SFLH 3.708,4.167 4.188,4.396 0.479,0.229 10 false SFLR 3.729,4.625 4.208,4.854 0.479,0.229 10 false SRRH 3.729,5.042 4.208,5.271 0.479,0.229 10 false SRRR 3.729,5.479 4.208,5.708 0.479,0.229 10 false SRLH 3.719,5.917 4.198,6.146 0.479,0.229 10 false SRLR

DTC Code DTC Detection Condition Trouble Area
C0226/21
C0236/22
C0246/23
C0256/24
Open or short in solenoid circuit continues for 0.05 seconds or more. VSC actuator (skid control ECU)
C1225/25
C1226/26
C122727
C1228/28
When any of following conditions detected:
1.

During switching solenoid (SMC1, SMC2, SRC1 or SRC2) ON signal input, overcurrent continues for 0.05 seconds or more.

2.

During switching solenoid (SMC1, SMC2, SRC1 or SRC2) OFF signal input, open circuit continues for 0.05 seconds or more.

3.

During switching solenoid (SMC1, SMC2, SRC1 or SRC2) ON signal input, open circuit continues for 0.01 seconds or more.

4.

During switching solenoid (SMC1, SMC2, SRC1 or SRC2) OFF signal input, current continues to be applied for 0.1 seconds or more.

5.

Short to GND in switching solenoid (SMC1, SMC2, SRC1 or SRC2) continues for 0.1 seconds or more.

6.

Switching solenoids (SMC1, SMC2, SRC1 or SRC2) shorted for 0.1 seconds or more.


VSC actuator (skid control ECU)

CAUTION / NOTICE / HINT

NOTICE:

When replacing the VSC actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.RECONFIRM DTC

b.

Start the engine.


c.

Check if the same DTC(s) is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is output A
DTC is not output B

HINT:

The DTCs may be stored due to a malfunction in the connector terminal.




A

B