Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM27L0U _54 Brake _049321 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0235735 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C0273/13  Open in ABS Motor Relay Circuit  C1251/51  Open in Pump Motor Circuit  


DESCRIPTION

The ABS motor relay (skid control ECU interior circuit) supplies the power to the ABS pump motor. While the ABS is activated, the ECU turns the motor relay ON and operates the ABS pump motor.

DTC Code DTC Detection Condition Trouble Area
C0273/13 When one of following conditions is met:
1.

Pump motor voltage is 2.0 V or more for 1 sec. or more at motor relay OFF.

2.

Pump motor voltage is (IG - 4.0 V) or less for 0.1 sec. or more at motor relay ON.

3.

After the end of the actuation of the motor relay, slow down condition of motor does not meet the specification.


·

ABS1 H-fuse

·

Harness or connector (+BM circuit)

·

VSC actuator (skid control ECU)


C1251/51 When any of following conditions detected with normal battery voltage (10 V or more):
1.

Open in pump motor power supply circuit or open in motor power supply circuit ground

2.

Motor stuck mechanically and does not operate

3.

Motor coil shorted and overcurrent flows


·

ABS1 H-fuse

·

VSC actuator (skid control ECU)



HINT:

C0273/13: The skid control ECU begins to detect these DTCs when the vehicle speed exceeds 15 km/h (9 mph).


WIRING DIAGRAM

C152722E07
3.757,1.566 4.158,1.731 0.401,0.165 10 ABS1 1.249,3.522 1.739,3.720 0.489,0.198 10 Battery 5.569,3.158 6.017,3.328 0.448,0.170 10 GND1 5.588,1.397 5.913,1.567 0.325,0.170 10 +BM 5.393,1.29 5.504,1.446 0.112,0.156 10 1 5.314,3.051 5.504,3.202 0.190,0.151 10 16 5.443,4.2 5.752,4.365 0.309,0.165 10 A19 5.429,4.34 6.576,4.505 1.147,0.165 10 Skid Control ECU

CAUTION / NOTICE / HINT

NOTICE:

When replacing the VSC actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (MOTOR RELAY)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream ON.



e.

Select the Active Test mode on the Techstream.

ABS/VSC/TRAC
Tester Display Test Part Control Range Diagnostic Note
Motor Relay Motor relay Relay ON/OFF Operating sound of motor can be heard


f.

Check the operation sound of the motor when operating it with the Techstream.

OK:

The operation sound of the motor can be heard.




OK

2.RECONFIRM DTC

NG

3.INSPECT FUSE (ABS1)
2.RECONFIRM DTC

b.

Start the engine.


c.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is output A
DTC is not output B



A

B

3.INSPECT FUSE (ABS1)
a.
C159681E03
0.062,0.117 1.783,0.301 1.721,0.184 10 Engine Room Relay Block 1.008,2.863 2.115,3.065 1.107,0.202 10 ABS1 H-fuse 1.623,2.126 1.369,2.845 false

Remove the ABS1 H-fuse from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ABS1 H-fuse Always Below 1 Ω




OK

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)

NG

CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)
a.
U153708E01
0.088,0.142 2.445,0.455 2.357,0.313 10 Front view of wire harness connector: (to Skid Control ECU) 2.858,1.51 3.174,1.659 0.316,0.149 10 +BM 0.154,1.51 0.577,1.666 0.423,0.156 10 GND1 0.183,1.167 0.505,1.342 0.323,0.174 10 A19 0.376,1.717 0.376,1.962 false 3.04,1.717 3.04,1.962 false

Disconnect the A19 ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A19-1 (+BM) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A19-16 (GND1) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR