Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM27L0U _54 Brake _049321 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0235735 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1247/47  Stroke Sensor Malfunction  


DESCRIPTION

Detects a problem with booster vacuum pressure and enters assist control.

DTC Code DTC Detection Condition Trouble Area
C1247/47 When either condition below is met:
1.

When the output becomes 4.7 V or more or 0.2 V or less per 0.1 seconds.

2.

When the output does not return to 2.5 V even when 0.5 seconds or more elapse, in spite of no change in brake operation.


·

Brake booster

·

Pedal stroke sensor

·

Pedal stroke sensor circuit

·

VSC actuator (skid control ECU)



WIRING DIAGRAM

C152731E07
0.525,1.843 0.829,2.026 0.304,0.184 10 A21 0.525,1.999 1.935,2.227 1.409,0.228 10 Pedal Stroke Sensor 5.598,1.885 5.902,2.068 0.304,0.184 10 A19 5.589,2.025 6.800,2.227 1.211,0.202 10 Skid Control ECU 5.85,0.867 6.191,1.041 0.341,0.174 10 VCP 5.85,1.184 6.191,1.359 0.341,0.174 10 PIM 5.85,1.492 6.080,1.667 0.230,0.174 10 E3 0.975,0.867 1.316,1.041 0.341,0.174 10 VCP 0.975,1.184 1.316,1.359 0.341,0.174 10 PIM 1.101,1.492 1.331,1.667 0.230,0.174 10 E3 1.362,0.754 1.490,0.924 0.128,0.170 10 1 1.362,1.084 1.490,1.254 0.128,0.170 10 5 1.362,1.385 1.490,1.555 0.128,0.170 10 3 5.572,0.754 5.763,0.924 0.191,0.170 10 26 5.572,1.084 5.763,1.254 0.191,0.170 10 30 5.572,1.385 5.763,1.555 0.191,0.170 10 27

CAUTION / NOTICE / HINT

NOTICE:

When replacing the VSC actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.READ VALUE USING TECHSTREAM (STROKE SENSOR)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Run the engine until the engine reaches 3000 rpm, and return it back to idle.

HINT:

Rev up the engine to ensure a sufficient vacuum.



d.

Select the Data List mode on the Techstream.

ABS/VSC/TRAC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stroke Sensor Pedal stroke sensor / min.: 0.00 V, max.: 5.00 V Approximately 1.90 V without the brake pedal depressed. -

HINT:
·

The result appears on the Techstream after some delay because a time lag occurs when using the Techstream.

·

If a signal from the pedal stroke sensor is sent between sampling, the result does not appear on the Techstream. So be sure to perform the measurement 2 or 3 times.




e.
C162015E05
0.083,2.563 1.885,2.771 1.802,0.208 10 false (1): Brake Pedal Depressed 0.083,2.938 1.885,3.146 1.802,0.208 10 false (2): Brake Pedal Released 0.75,0.979 0.979,1.156 0.229,0.177 10 false (1) 1.667,0.271 1.896,0.448 0.229,0.177 10 false (2) 0.698,0.177 1.219,0.365 0.521,0.188 10 false Voltage 0.177,0.656 0.563,0.823 0.385,0.167 10 false 4.5 V 0.177,1.417 0.563,1.583 0.385,0.167 10 false 1.9 V 0.177,1.74 0.563,1.906 0.385,0.167 10 false 0.5 V 2.604,2.229 2.948,2.417 0.344,0.188 10 false Time

Check that the brake pedal acceleration value of the pedal stroke sensor displayed on the Techstream changes by alternately depressing and releasing the brake pedal.

OK:

The value changes as shown in the illustration. (The value will return to approximately 1.9 V after the brake pedal is released.)


HINT:
·

The maximum voltage depends on pedal stroke speed but should not exceed 4.7 V or fall below 0.2 V.

·

Even if the result is as described above, a malfunction may still exist because there is a high possibility that the malfunction simulation will fail. Therefore, proceed to the troubleshooting procedures below.





NEXT

2.CHECK HARNESS AND CONNECTOR (PEDAL STROKE SENSOR - SKID CONTROL ECU)
2.CHECK HARNESS AND CONNECTOR (PEDAL STROKE SENSOR - SKID CONTROL ECU)
a.
U153715E02
1.01,1.135 0.875,1.521 true 1.458,1.135 1.292,1.521 true 2.104,1.073 1.51,1.521 true 1.26,3.604 0.854,4.302 true 1.75,3.844 1.594,4.323 true 1.927,3.604 2.083,4.333 true 0.229,0.896 0.51,1.063 0.281,0.167 10 false A19 0.125,3.26 0.406,3.427 0.281,0.167 10 false A21 0.698,4.333 1.052,4.5 0.354,0.167 10 false VCP 0.917,0.948 1.198,1.115 0.281,0.167 10 false PIM 1.427,0.927 1.708,1.094 0.281,0.167 10 false E3 1.469,4.333 1.75,4.5 0.281,0.167 10 false PIM 2.052,4.354 2.333,4.521 0.281,0.167 10 false E3 2.115,0.896 2.469,1.063 0.354,0.167 10 false VCP 0.198,0.042 2.573,0.375 2.375,0.333 10 false Front view of wire harness connector: (to Skid Control ECU) 0.125,2.365 2.479,2.688 2.354,0.323 10 false Front view of wire harness connector: (to Pedal Stroke Sensor)

Confirm that the skid control ECU connector and pedal stroke sensor connector are properly connected.


b.

Disconnect the A19 ECU connector.


c.

Disconnect the A21 sensor connector.


d.

Inspect both the connector case and the terminal for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A19-30 (PIM) - A21-5 (PIM) Always Below 1 Ω
A19-30 (PIM) - Body ground Always 10 kΩ or higher
A19-27 (E3) - A21-3 (E3) Always Below 1 Ω
A19-27 (E3) - Body ground Always 10 kΩ or higher
A19-26 (VCP) - A21-1 (VCP) Always Below 1 Ω
A19-26 (VCP) - Body ground Always 10 kΩ or higher




OK

3.INSPECT BRAKE BOOSTER ASSEMBLY (PEDAL STROKE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT BRAKE BOOSTER ASSEMBLY (PEDAL STROKE SENSOR)
a.
U153428E02
1.25,2 0.906,2.802 true 0.094,0.042 2.51,0.469 2.417,0.427 10 false Front view of wire harness connector: (to Pedal Stroke Sensor) 0.219,1.177 0.49,1.344 0.271,0.167 10 false A21 0.708,2.844 1.042,3 0.333,0.156 10 false VCP

Disconnect the A21 sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A21-1 (VCP) - Body ground Ignition switch ON 5.0 V




OK

REPLACE BRAKE BOOSTER ASSEMBLY

NG