Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM27L0U _54 Brake _049321 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0235735 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C0278/11  Open or Short Circuit in ABS Solenoid Relay Circuit  


DESCRIPTION

The solenoid relay (skid control ECU interior circuit) supplies power to the ABS solenoid and TRC solenoid.

After the ignition switch is turned to ON, the solenoid is determined to be normal by the initial check self-diagnosis, the relay switches on. If any open or short circuits are detected, the relay switches off.

This DTC may be set if the voltage supply to the solenoid relay (+BS) falls below the DTC detection threshold due to the battery or alternator outputs being insufficient.

DTC Code DTC Detection Condition Trouble Area
C0278/11 Either condition is met:
1.

Malfunction in skid control ECU continues for 0.056 seconds or more.

2.

Voltage supply to solenoid valve stops for 0.056 seconds or more.


·

ABS2 H-fuse

·

Harness or connector (+BS circuit)

·

VSC actuator (skid control ECU)



WIRING DIAGRAM

C152722E08
3.757,1.566 4.158,1.731 0.401,0.165 10 ABS2 1.249,3.522 1.739,3.720 0.489,0.198 10 Battery 5.569,3.158 6.017,3.328 0.448,0.170 10 GND1 5.588,1.397 5.892,1.567 0.304,0.170 10 +BS 5.33,1.29 5.518,1.446 0.188,0.156 10 32 5.335,3.051 5.518,3.239 0.183,0.188 10 16 5.443,4.2 5.752,4.365 0.309,0.165 10 A19 5.429,4.34 6.576,4.505 1.147,0.165 10 Skid Control ECU

CAUTION / NOTICE / HINT

NOTICE:

When replacing the VSC actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.INSPECT FUSE (ABS2)
a.
C152723E03
0.065,0.235 1.758,0.419 1.693,0.184 10 Engine Room Relay Block: 1.088,2.91 2.126,3.076 1.038,0.165 10 ABS2 H-fuse 1.798,2.147 1.463,2.827 false

Remove the ABS2 H-fuse from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ABS2 H-fuse Always Below 1 Ω




OK

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)

NG

CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)
a.
U153709E01
0.097,0.049 2.454,0.362 2.357,0.313 10 Front view of wire harness connector: (to Skid Control ECU) 2.862,2.712 3.164,2.861 0.302,0.149 10 +BS 0.145,1.485 0.568,1.641 0.423,0.156 10 GND1 3.047,2.439 3.047,2.701 false 0.191,1.143 0.514,1.317 0.323,0.174 10 A19 0.385,1.693 0.385,1.938 false

Disconnect the A19 ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A19-32 (+BS) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A19-16 (GND1) - Body ground Always Below 1 Ω




OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.RECONFIRM DTC

b.

Start the engine.


c.

Check if the same DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is output A
DTC is not output B



A

B