Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM27L0U _54 Brake _049321 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0235735 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1340/47  Center Differential Lock Circuit  


DESCRIPTION

When the vehicle is changed to 4WD (L4 mode) and the center differential locks, VSC control turns off and the VSC OFF indicator light illuminates.

DTC Code DTC Detection Condition Trouble Area
C1340/47 When the terminal IG1 voltage is between 10 and 14 V, there is an open in the center differential lock detection switch circuit or there is a transfer mechanical malfunction for 2 seconds or more.
·

Center differential lock detection switch

·

Center differential lock detection switch circuit

·

4WD control ECU

·

VSC actuator (skid control ECU)



WIRING DIAGRAM

C193649E05
0.559,4.171 1.728,4.354 1.169,0.184 10 4WD Control ECU 2.799,3.662 4.310,4.179 1.511,0.517 10 Transfer Shift Actuator (Center Differential Lock Detection Switch) 5.715,4.009 6.028,4.193 0.313,0.184 10 A19 5.841,1.917 6.182,2.100 0.341,0.184 10 EXI2 1.152,3.075 1.493,3.259 0.341,0.184 10 4WD 5.546,1.8 5.786,1.984 0.239,0.184 10 11 5.546,1.221 5.786,1.405 0.239,0.184 10 13 5.546,0.708 5.786,0.891 0.239,0.184 10 12 5.715,4.196 6.954,4.379 1.239,0.184 10 Skid Control ECU 2.819,1.088 4.447,1.268 1.628,0.181 10 CAN Communication Line 1.092,0.834 1.558,1.018 0.466,0.184 10 CANH 1.092,1.363 1.558,1.546 0.466,0.184 10 CANL 5.818,0.834 6.283,1.018 0.466,0.184 10 CANH 5.818,1.363 6.283,1.546 0.466,0.184 10 CANL 1.6,0.664 1.818,0.843 0.218,0.179 10 19 1.6,1.193 1.818,1.372 0.218,0.179 10 20 0.573,4.004 0.916,4.230 0.343,0.225 10 A28 1.608,2.943 1.826,3.122 0.218,0.179 10 14 3.019,3.167 3.362,3.392 0.343,0.225 10 CDL 3.62,3.169 4.052,3.394 0.431,0.225 10 GND1 2.85,2.941 2.971,3.120 0.121,0.179 10 3 4.105,2.941 4.207,3.120 0.103,0.179 10 7 2.813,3.491 3.156,3.717 0.343,0.225 10 D45

CAUTION / NOTICE / HINT

NOTICE:

When replacing the VSC actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


HINT:

If the transfer shift actuator cannot change from 2WD to 4WD or 4WD to 2WD or cannot lock the center differential, inspect and repair the touch select 2-4 and high-low systems first.


PROCEDURE

1.INSPECT SKID CONTROL ECU (EXI2 TERMINAL)
a.

Set the vehicle in the 4WD with center differential locked state using the center differential lock detection switch.


b.
U153711E01
0.097,0.09 2.454,0.418 2.357,0.327 10 Front view of wire harness connector: (to Skid Control ECU) 1.161,1.394 1.486,1.550 0.325,0.156 10 EXI2 0.191,1.356 0.514,1.531 0.323,0.174 10 A19 1.343,1.576 1.343,1.949 false

Disconnect the A19 ECU connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A19-11 (EXI2) - Body ground
·

Ignition switch ON

·

4WD with center differential locked (Center differential lock detection switch ON)


Below 1.5 V



e.

Connect the A19 ECU connector.


f.

Set the vehicle in the 2WD or 4WD with center differential free state using the center differential lock detection switch.


g.

Disconnect the A19 ECU connector.


h.

Turn the ignition switch to ON.


i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A19-11 (EXI2) - Body ground
·

Ignition switch ON

·

2WD or 4WD with center differential free (Center differential lock detection switch OFF)


10 to 14 V




OK

NG

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - 4WD CONTROL ECU)
2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - 4WD CONTROL ECU)
a.
C353361E01
0.052,0.771 0.438,0.99 0.385,0.219 0.094,3.135 0.479,3.354 0.385,0.219 1.344,1.229 1.677,0.938 true 2.198,3.896 2.042,4.417 true 0.104,0.021 2.375,0.375 2.271,0.354 10 false Front view of wire harness connector: (to Skid Control ECU) 0.125,0.802 0.448,0.99 0.323,0.188 10 false A19 1.719,0.813 2.167,1 0.448,0.188 10 false EXI2 0.167,2.188 2.438,2.542 2.271,0.354 10 false Front view of wire harness connector: (to 4WD Control ECU) 0.156,3.177 0.479,3.365 0.323,0.188 10 false A28 1.792,4.448 2.188,4.635 0.396,0.188 10 false 4WD

Confirm that the skid control ECU connector and 4WD control ECU connector are properly connected.


b.

Disconnect the A19 and A28 ECU connectors.


c.

Disconnect the D45 transfer shift actuator connector.


d.

Inspect both the connector case and the terminal for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A19-11 (EXI2) - A28-14 (4WD) Always Below 1 Ω
A19-11 (EXI2) - Body ground Always 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (4WD CONTROL ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (4WD CONTROL ECU - BODY GROUND)
a.

Confirm that the 4WD control ECU connector and transfer shift actuator connectors are properly connected.

U153489E02
2.406,1.292 1.792,2.031 1.792,2.031 1.792,2.229 true 2.698,0.5 3,0.667 0.302,0.167 10 false A28 0.177,0.01 2.573,0.448 2.396,0.438 10 false Component with harness connected: (4WD Control ECU) 1.635,2.26 1.969,2.448 0.333,0.188 10 false 4WD


b.

Disconnect the A28 ECU connector.


c.

Inspect the connector case and the terminal for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Connect the A28 ECU connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-14 (4WD) - Body ground 4WD with center differential locked
(Center differential lock detection switch ON)
Below 1 Ω
2WD or 4WD with center differential free
(Center differential lock detection switch OFF)
10 kΩ or higher




OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.RECONFIRM DTC

b.

Start the engine.


c.

Check if the same DTC(s) is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is output A
DTC is not output B



A

B