Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM27L0U _54 Brake _049321 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0235735 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  AUTO LSD Indicator Light does not Come ON  


CAUTION / NOTICE / HINT

NOTICE:

When replacing the VSC actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

2.CHECK CONNECTOR CONNECTION CONDITION

B

2.CHECK CONNECTOR CONNECTION CONDITION
a.

Check the skid control ECU connector connection condition.

OK:

The connector is securely connected.




OK

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)

NG

CONNECT CONNECTOR CORRECTLY

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)
a.
U153712E01
0.097,0.133 2.454,0.447 2.357,0.313 10 Front view of wire harness connector: (to Skid Control ECU) 0.145,1.501 0.568,1.657 0.423,0.156 10 GND1 0.191,1.159 0.514,1.333 0.323,0.174 10 A19 0.385,1.709 0.385,1.954 false 1.675,1.501 1.922,1.657 0.247,0.156 10 IG1 1.794,1.709 1.794,1.946 false

Disconnect the A19 ECU connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A19-8 (IG1) - Body ground Ignition switch ON 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
A19-16 (GND1) - Body ground Always Below 1 Ω




OK

4.PERFORM ACTIVE TEST USING TECHSTREAM (AUTO LSD INDICATOR LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.PERFORM ACTIVE TEST USING TECHSTREAM (AUTO LSD INDICATOR LIGHT)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream ON.


d.

Select the Active Test mode and operate the AUTO LSD indicator light using the Techstream.

ABS/VSC/TRAC
Tester Display Test Part Control Range Diagnostic Note
Auto LSD Indicator Light AUTO LSD indicator light Indicator light ON/OFF Observe combination meter


e.

Check that the AUTO LSD indicator light turns on and off in the combination meter when using the Techstream.

OK:

The AUTO LSD indicator light turns ON and OFF in accordance with the Techstream operation.




OK

5.INSPECT VSC OFF SWITCH

NG

5.INSPECT VSC OFF SWITCH
a.
C179171E02
0.25,0.044 2.740,0.520 2.489,0.476 10 Component without harness connected: (VSC OFF Switch) 0.517,2.848 1.183,3.021 0.666,0.174 10 : No pin

Remove the VSC OFF switch (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 - 9 Switch is pressed Below 1 Ω
Switch is not pressed 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH AND BODY GROUND)

NG

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH AND BODY GROUND)
a.
U153719E02
2.417,1.573 2.417,1.25 true 0.24,0.104 2.51,0.417 2.271,0.313 10 false Front view of wire harness connector: (to Skid Control ECU) 0.177,0.958 0.448,1.135 0.271,0.177 10 false A19 2.26,1.042 2.625,1.188 0.365,0.146 10 false CSW 0.26,2.646 2.521,2.969 2.26,0.323 10 false Front view of wire harness connector: (to VSC OFF Switch) 0.573,3.781 0.865,3.958 0.292,0.177 10 false H29

Disconnect the A19 ECU connector.


b.

Disconnect the H29 switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A19-4 (CSW) - H29-9 Always Below 1 Ω
A19-4 (CSW) - Body ground Always 10 kΩ or higher
H29-6 - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR