Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM27L0U _54 Brake _049321 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0235735 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1267/28  Brake Pedal Load Sensing Switch  


DESCRIPTION

The skid control ECU detects if the brake pedal is depressed.

DTC Code DTC Detection Condition Trouble Area
C1267/28 When one of following conditions is met:
1.

Micro switch signal PSNC and PSNO logic malfunction.

2.

When brake pedal is not depressed, micro switch turns on.

3.

When brake pedal is depressed, micro switch turns off.


·

Booster pedal micro switch (active brake booster)

·

Booster pedal micro switch (active brake booster) circuit

·

VSC actuator (skid control ECU)



WIRING DIAGRAM

C152731E08
0.265,1.843 0.569,2.026 0.304,0.184 10 A20 0.256,1.983 1.595,2.178 1.340,0.195 10 Active Brake Booster 5.598,1.885 5.902,2.068 0.304,0.184 10 A19 5.589,2.025 6.800,2.227 1.211,0.202 10 Skid Control ECU 0.975,0.867 1.316,1.041 0.341,0.174 10 STS 0.877,1.184 1.315,1.359 0.438,0.174 10 PSNC 0.877,1.478 1.315,1.653 0.438,0.174 10 PSNO 5.86,0.867 6.201,1.041 0.341,0.174 10 STS 5.846,1.478 6.284,1.653 0.438,0.174 10 PSNO 5.846,1.198 6.284,1.373 0.438,0.174 10 PSNC 1.362,0.761 1.490,0.931 0.128,0.170 10 5 1.362,1.084 1.490,1.254 0.128,0.170 10 2 1.362,1.392 1.490,1.562 0.128,0.170 10 1 5.572,0.768 5.763,0.938 0.191,0.170 10 21 5.572,1.39 5.763,1.560 0.191,0.170 10 24 5.572,1.077 5.763,1.247 0.191,0.170 10 23

CAUTION / NOTICE / HINT

NOTICE:

When replacing the VSC actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK TERMINAL VOLTAGE (BOOSTER PEDAL MICRO SWITCH)
a.
C353359E01
0.167,1.375 0.583,1.615 0.417,0.24 1.76,2.531 1.76,2.073 true 0.052,0.135 2.333,0.49 2.281,0.354 10 false Front view of wire harness connector: (to Active Brake Booster) 0.25,1.417 0.625,1.604 0.375,0.188 10 false A20 1.656,2.583 2.031,2.771 0.375,0.188 10 false STS

Disconnect A20 booster connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A20-5 (STS) - Body ground Ignition switch ON 4.3 to 6.3 V




OK

2.INSPECT BOOSTER PEDAL MICRO SWITCH

NG

3.CHECK HARNESS AND CONNECTOR (BOOSTER PEDAL MICRO SWITCH - SKID CONTROL ECU)
2.INSPECT BOOSTER PEDAL MICRO SWITCH
C162424E04
0.244,0.715 0.485,0.885 0.241,0.170 10 ON 2.337,0.576 3.240,0.746 0.903,0.170 10 (Oscilloscope) 2.337,2.173 3.240,2.343 0.903,0.170 10 (Oscilloscope) 0.249,1.663 0.888,1.814 0.639,0.151 10 2 (PSNC) 0.256,1.101 0.888,1.253 0.632,0.151 10 1 (PSNO) 1.399,1.358 0.897,1.168 false 1.399,1.473 0.909,1.735 false 1.927,1.222 2.451,1.373 0.524,0.151 10 5 (STS) 1.504,1.522 1.915,1.296 false 3.511,0.071 4.279,0.241 0.767,0.170 10 (Reference) 4.366,0.509 5.226,0.832 0.860,0.323 10 Brake Pedal Released 5.645,0.509 6.453,0.834 0.808,0.325 10 Brake Pedal Depressed 5.953,1.234 6.697,1.404 0.744,0.170 10 PSNO-STS 5.953,1.682 6.697,1.852 0.744,0.170 10 PSNC-STS 5.917,1.305 5.763,1.121 false 5.917,1.744 5.763,2.027 false 3.768,1.04 4.161,1.210 0.393,0.170 10 6.7 V 3.768,1.334 4.022,1.504 0.254,0.170 10 0 V 3.768,1.656 4.161,1.826 0.393,0.170 10 6.7 V 3.768,1.95 4.022,2.120 0.254,0.170 10 0 V 4.366,0.25 5.560,0.428 1.194,0.178 10 Ignition Switch ON

a.

When using an oscilloscope:

i.

Connect the oscilloscope between terminals 1 (PSNO) and 5 (STS), 2 (PSNC) and 5 (STS) of the brake booster with connector being connected.


ii.

Turn the ignition switch to ON.


iii.

Check the signal waveform while the brake pedal is depressed and released.

OK:

Signal waveform changes as shown in the illustration.




b.
C353359E02
0.313,1.25 0.635,1.5 0.323,0.25 1.448,1.792 1.25,1.365 true 1.656,1.802 1.792,1.354 true 1.792,2.5 1.792,2.094 true 0.188,0.073 2.469,0.458 2.281,0.385 10 false Front view of wire harness connector: (to Active Brake Booster) 0.365,1.302 0.656,1.49 0.292,0.188 10 false A20 0.917,1.177 1.51,1.354 0.594,0.177 10 false PSNO 1.635,1.167 2.229,1.344 0.594,0.177 10 false PSNC 1.698,2.542 2.292,2.719 0.594,0.177 10 false STS

When not using an oscilloscope:

i.

Disconnect the A20 booster connector.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A20-2 (PSNC) - A20-5 (STS) Brake pedal is depressed 6 V
A20-1 (PSNO) - A20-5 (STS) Brake pedal is released





OK

3.CHECK HARNESS AND CONNECTOR (BOOSTER PEDAL MICRO SWITCH - SKID CONTROL ECU)

NG

REPLACE BRAKE BOOSTER ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (BOOSTER PEDAL MICRO SWITCH - SKID CONTROL ECU)
a.
C353360E01
0.063,0.948 0.458,1.177 0.396,0.229 0.229,3.469 0.625,3.698 0.396,0.229 1.708,1.594 1.427,1.083 true 1.875,1.594 1.875,1.083 true 2.208,1.583 2.51,1.115 true 1.667,3.75 1.49,3.333 true 1.896,3.781 2.031,3.344 true 1.792,4.354 1.792,4 true 0.135,0.052 2.427,0.396 2.292,0.344 10 false Front view of wire harness connector: (to Skid Control ECU) 1.021,0.906 1.469,1.104 0.448,0.198 10 false PSNO 2.51,0.948 2.958,1.146 0.448,0.198 10 false STS 1.688,0.885 2.135,1.083 0.448,0.198 10 false PSNC 0.156,0.99 0.604,1.188 0.448,0.198 10 false A19 0.083,2.292 2.375,2.635 2.292,0.344 10 false Front view of wire harness connector: (to Active Brake Booster) 0.313,3.51 0.76,3.708 0.448,0.198 10 false A20 1.188,3.167 1.635,3.365 0.448,0.198 10 false PSNC 1.906,3.156 2.354,3.354 0.448,0.198 10 false PSNO 1.698,4.375 2.146,4.573 0.448,0.198 10 false STS

Confirm that the skid control ECU connector and brake booster connector are properly connected.


b.

Disconnect the A19 ECU connector.


c.

Disconnect the A20 booster connector.


d.

Inspect both the connector case and the terminal for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A19-24 (PSNO) - A20-1 (PSNO) Always Below 1 Ω
A19-24 (PSNO) - Body ground Always 10 kΩ or higher
A19-23 (PSNC) - A20-2 (PSNC) Always Below 1 Ω
A19-23 (PSNC) - Body ground Always 10 kΩ or higher
A19-21 (STS) - A20-5 (STS) Always Below 1 Ω
A19-21 (STS) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR