Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM27L0U _55 Steering _049326 POWER ASSIST SYSTEMS _0235759 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1531  ECU Malfunction  


DESCRIPTION

This circuit supplies electric power to the power steering solenoid valve. The power steering solenoid valve is built into the vane pump assembly.

The power steering ECU controls the output current to the power steering solenoid valve in accordance with the steering angle signal, steering zero point memory, vehicle speed signal and engine speed signal, adjusting the amount of power steering assist.

DTC No. DTC Detection Condition Trouble area
C1531 A short or open in the solenoid valve circuit
·

Harness or connector

·

Vane pump assembly (Power steering solenoid valve)

·

Power steering ECU assembly



WIRING DIAGRAM

C210556E10
4.989,2.252 6.961,2.433 1.972,0.181 10 Power Steering ECU Assembly 1.98,1.032 4.038,1.388 2.058,0.356 10 Vane Pump Assembly (Power Steering Solenoid Valve) 5.504,0.735 5.887,0.917 0.384,0.181 10 SOF+ 5.504,1.702 5.852,1.883 0.349,0.181 10 SOF- 5.302,0.652 5.458,0.833 0.156,0.181 10 7 5.302,1.605 5.458,1.786 0.156,0.181 10 8 3.505,0.658 3.661,0.839 0.156,0.181 10 2 2.209,0.658 2.365,0.839 0.156,0.181 10 1 1.986,0.873 2.398,1.055 0.412,0.181 10 D51 4.989,2.083 5.375,2.265 0.386,0.181 10 H117 2.393,0.637 2.742,0.818 0.349,0.181 10 SOF- 3.024,0.637 3.407,0.818 0.384,0.181 10 SOF+

PROCEDURE

1.READ VALUE USING TECHSTREAM (SOLENOID CURRENT)
a.

Turn the ignition switch off.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the Techstream on.


e.

Enter the following menus: Chassis / PPS / Data List.


f.

According to the display on the Techstream, read the Data List.

PPS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Solenoid Current Solenoid Current/
Min.: 0 mA
Max.: 1000 mA
200 to 950 mA The engine is running and the steering wheel is being turned.

OK:

The normal condition value is displayed the Techstream.




OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - POWER STEERING SOLENOID VALVE)
2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - POWER STEERING SOLENOID VALVE)
a.

Disconnect the power steering ECU and power steering solenoid valve connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H117-7 (SOF+) - D51-2 (SOF+) Always Below 1 Ω
H117-8 (SOF-) - D51-1 (SOF-) Always
H117-7 (SOF+) - Body ground Always 10 kΩ or higher
H117-8 (SOF-) - Body ground Always




OK

3.INSPECT VANE PUMP ASSEMBLY (POWER STEERING SOLENOID VALVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT VANE PUMP ASSEMBLY (POWER STEERING SOLENOID VALVE)
C225484E01
0.115,0.044 0.326,0.215 0.211,0.171 10 *a 1.244,4.08 1.463,4.291 0.219,0.211 10 (+) 2.102,4.08 2.321,4.291 0.219,0.211 10 (-)

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 6.7 to 7.3 Ω



b.

Connect the battery positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating noise.

OK:

The solenoid makes an operating sound.


Text in Illustration
*a Component without harness connected
(Power Steering Solenoid Valve)



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG