Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM27L0U _55 Steering _049326 POWER ASSIST SYSTEMS _0235759 POWER STEERING SYSTEM G

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT DRIVE BELT

a.

Visually check the belt for excessive wear, frayed cords, etc.

If any defect is found, replace the drive belt.

HINT:
·

Replace the belt if there are any missing ribs.

·

After installing a belt, check that it fits properly in the ribbed grooves.

·

Check with your hand to confirm that the belt has not slipped out of the grooves on the bottom of the pulley.




Hide 2.BLEED POWER STEERING SYSTEM

a.

Check the fluid level.


b.

Jack up the front of the vehicle and support it with stands.


c.

Turn the steering wheel.

i.

With the engine stopped, turn the wheel slowly from lock to lock several times.



d.

Lower the vehicle.


e.

Start the engine.


f.

Run the engine at idle for a few minutes.


g.

Turn the steering wheel.

i.

With the engine idling, turn the wheel left or right to the full lock position and keep it there for 2 to 3 seconds, then turn the wheel to the opposite full lock position and keep it there for 2 to 3 seconds.(*1)


ii.

Repeat (*1) several times.



h.

Stop the engine.


i.
C124274E04
0.922,1.874 1.098,2.024 0.176,0.150 10 *a 2.32,1.874 2.505,2.024 0.185,0.150 10 *b

Check for foaming or emulsification.

Text in Illustration
*a Correct
*b Incorrect

If the system has to be bled twice because of foaming or emulsification, check for fluid leaks in the system.


j.

Check the fluid level.


Hide 3.CHECK FLUID LEVEL

a.
C158723E02
0.478,0.875 0.653,1.056 0.174,0.180 10 *a 2.794,0.751 2.968,0.917 0.174,0.166 10 *b

Keep the vehicle horizontal.

Text in Illustration
*a COLD range
*b HOT range


b.

With the engine stopped, check the fluid level in the reservoir.

If necessary, add fluid.

Fluid:

ATF DEXRON II or III


HINT:

If the fluid is hot, check that the fluid level is within the HOT range. If the fluid is cold, check that the fluid level is within the COLD range.



c.

Start the engine and run it at idle.


d.

Turn the steering wheel from lock to lock several times to raise fluid temperature.

Fluid temperature:

80°C (176°F)



e.
C124274E04
0.922,1.874 1.098,2.024 0.176,0.150 10 *a 2.32,1.874 2.505,2.024 0.185,0.150 10 *b

Check for foaming or emulsification.

Text in Illustration
*a Correct
*b Incorrect

If foaming or emulsification is identified, bleed the power steering system.


f.
U153404E01
0.858,1.589 1.046,1.739 0.187,0.150 10 *a 1.632,1.368 1.825,1.530 0.192,0.162 10 *c 2.356,1.589 2.533,1.739 0.177,0.150 10 *b 1.437,0.986 1.835,0.986 false 1.591,0.909 2.006,0.909 false 1.718,0.808 1.718,0.545 false 1.726,1.092 1.726,1.355 false

With the engine idling, measure the fluid level in the reservoir.

Text in Illustration
*a Engine idling
*b Engine stopped
*c 5.0 mm (0.197 in.) or less


g.

Stop the engine.


h.

Wait a few minutes and remeasure the fluid level in the reservoir.

Maximum fluid level rise:

5.0 mm (0.197 in.)


If a problem is found, bleed the power steering system.


i.

Check the fluid level.


Hide 4.CHECK STEERING FLUID PRESSURE

a.

Disconnect the pressure feed tube from the vane pump (See page Steering>POWER ASSIST SYSTEMS>VANE PUMP(for 3UR-FE, 3UR-FBE)>REMOVAL).


b.

Connect SST as shown in the illustration.

SST
09640-10010  (09641-01010, 09641-01030, 09641-01060)

NOTICE:

Check that the valve of SST is in the open position.



c.

Bleed the power steering system.


d.

Start the engine and run it at idle.


e.

Turn the steering wheel from lock to lock several times to raise fluid temperature.

Fluid temperature:

80°C (176°F)


C161566E04
5.396,0.167 5.677,0.167 false 5.469,3.104 5.198,3.104 false 1.333,2.875 1.333,3.042 false 2.448,2.25 2.448,3.031 false 4.667,1.552 4.885,1.719 0.219,0.167 10 false *a 6.146,1.531 6.531,1.698 0.385,0.167 10 false *b 5.729,0.083 6.063,0.26 0.333,0.177 10 false SST 1.26,3.052 1.448,3.229 0.188,0.177 10 false *1 5.521,3.042 6.313,3.219 0.792,0.177 10 false *1 2.396,3.063 2.583,3.26 0.188,0.198 10 false *2

Text in Illustration
*1 Attachment *2 Pressure Feed Tube
*a IN *b OUT


f.
C353591E01
0.365,0.885 0.677,1.083 0.313,0.198 10 false *1 2.656,0.333 2.969,0.531 0.313,0.198 10 false *2 2.667,1.396 2.979,1.594 0.313,0.198 10 false *3 1.26,0.948 1.573,1.146 0.313,0.198 10 false *a 1.385,1.656 1.74,1.854 0.354,0.198 10 false SST

With the engine idling, close the valve of SST and observe the reading on SST.

Minimum fluid pressure:

8336 kPa (85.0 kgf/cm2, 1209 psi)


Text in Illustration
*1 Power Steering Gear Assembly
*2 Vane Pump Oil Reservoir Assembly
*3 Vane Pump Assembly
*a Valve Closed

NOTICE:
·

Do not keep the valve closed for more than 10 seconds.

·

Do not allow the fluid temperature to become too high.



If not within the specified range, check for fluid leaks and replace parts as necessary.


g.

With the engine idling, fully open the valve.


h.
C353592E01
0.354,0.917 0.667,1.115 0.313,0.198 10 false *1 2.688,0.354 3,0.552 0.313,0.198 10 false *2 2.698,1.385 3.01,1.583 0.313,0.198 10 false *3 1.333,0.969 1.646,1.167 0.313,0.198 10 false *a 1.469,1.646 1.813,1.844 0.344,0.198 10 false SST

Measure the fluid pressure at engine speeds of 1000 rpm and 3000 rpm.

Difference in fluid pressure:

490 kPa (5.0 kgf/cm2, 71 psi) or less


Text in Illustration
*1 Power Steering Gear Assembly
*2 Vane Pump Oil Reservoir Assembly
*3 Vane Pump Assembly
*a Valve Open

NOTICE:

Do not turn the steering wheel.


If not within the specified range, check for fluid leaks and replace parts as necessary.


i.
C353595E01
0.354,0.854 0.667,1.052 0.313,0.198 10 false *1 2.656,0.26 2.969,0.458 0.313,0.198 10 false *2 2.656,1.365 2.969,1.563 0.313,0.198 10 false *3 1.219,0.885 1.531,1.083 0.313,0.198 10 false *a 1.375,1.594 1.688,1.792 0.313,0.198 10 false SST

With the engine idling and the valve fully open, turn the steering wheel left or right to the full lock position. Observe the reading on SST.

Minimum fluid pressure:

8336 kPa (85.0 kgf/cm2, 1209 psi)


Text in Illustration
*1 Power Steering Gear Assembly (Lock Position)
*2 Vane Pump Oil Reservoir Assembly
*3 Vane Pump Assembly
*a Valve Open

NOTICE:
·

Do not keep the steering wheel in the full lock position for more than 10 seconds.

·

Do not allow the fluid temperature to become too high.



If not within the specified range, check for fluid leaks and replace parts as necessary.


j.

Disconnect SST.



l.

Bleed the power steering system.