Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM
RM27L0U _55 Steering _049327 STEERING COLUMN _0235762 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM C

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  B2602  Key Unlock Warning Switch Circuit Malfunction  


DESCRIPTION

A signal (ON or OFF) is sent from the main body ECU to the multiplex tilt and telescopic ECU via the CAN communication bus when the ignition key is inserted into the key cylinder. The multiplex tilt and telescopic ECU uses this signal to operate the auto away or auto return function.

DTC Code Detection Condition Trouble Area
B2602 When both conditions below are met:
·

Unlock warning switch signal is OFF.

·

Ignition switch is turned ON.


·

Unlock warning switch

·

Unlock warning switch circuit

·

Main body ECU

·

Multiplex tilt and telescopic ECU



WIRING DIAGRAM

C353585E01
0.958,0.979 1.563,1.177 0.604,0.198 10 false CANP 0.958,1.938 1.552,2.125 0.594,0.188 10 false CANN 0.99,2.896 1.573,3.083 0.583,0.188 10 false KSW 1.49,0.99 1.802,1.188 0.313,0.198 10 false H2 1.5,1.938 1.813,2.135 0.313,0.198 10 false H2 1.479,2.896 1.792,3.094 0.313,0.198 10 false H1 1.49,0.771 1.802,0.969 0.313,0.198 10 false 16 1.49,1.719 1.802,1.917 0.313,0.198 10 false 15 1.542,2.667 1.854,2.865 0.313,0.198 10 false 5 5.573,0.875 5.885,1.073 0.313,0.198 10 false 5 2.427,2.781 2.583,2.979 0.156,0.198 10 false 1 3.292,2.771 3.448,2.969 0.156,0.198 10 false 2 0.5,3.542 2.49,3.74 1.99,0.198 10 false Main Body ECU 2.354,3.198 4.344,3.396 1.99,0.198 10 false H21 2.354,3.375 3.406,3.865 1.052,0.49 10 false Unlock Warning Switch 5.052,3.417 5.51,3.615 0.458,0.198 10 false H57 5.042,3.604 7.156,3.833 2.115,0.229 10 false Multiplex Tilt and Telescopic ECU

PROCEDURE

1.CHECK OTHER DTC OUTPUT
HINT:

The power tilt and power telescopic steering column system uses the CAN communication system, so check its diagnostic system before proceeding to troubleshooting.


a.

Check if the power tilt and telescopic steering column system DTC B2621 is output.

Result
Result Proceed to
No output A
B2621 is output B

HINT:
·

If DTC B2621 and B2602 are output, perform troubleshooting for B2621 first.

·

DTC B2621 indicates a communication interruption for the power tilt and power telescopic steering column system.





A

2.READ VALUE USING TECHSTREAM (UNLOCK WARNING SWITCH COMMUNICATION SIGNAL)

B

2.READ VALUE USING TECHSTREAM (UNLOCK WARNING SWITCH COMMUNICATION SIGNAL)
a.

Use the Data List to check if the unlock warning communication signal is functioning properly.

Tilt & Telescopic
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Key Switch (CAN) Communication state of unlock warning switch signal / ON or OFF ON: Communication is normal
OFF: Communication is interrupted
-


Result
Result Proceed to
"OFF" is displayed. A
"ON" is displayed. B


A

3.INSPECT UNLOCK WARNING SWITCH

B

3.INSPECT UNLOCK WARNING SWITCH
C159210E02
4.227,0.411 6.741,0.811 2.513,0.399 10 Component without harness connected: (Unlock Warning Switch)

a.

Disconnect the H21 connector from the unlock warning switch.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Unlock warning switch OFF (Ignition key is removed) 10 kΩ or higher
1 - 2 Unlock warning switch ON (Ignition key is inserted) Below 1 Ω




OK

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - UNLOCK WARNING SWITCH)

NG

REPLACE UNLOCK WARNING SWITCH

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - UNLOCK WARNING SWITCH)
U153461E02
5.156,1.927 5.896,1.677 false 0.51,0.094 2.833,0.625 2.323,0.531 10 false Front view of wire harness connector: (to Unlock Warning Switch) 5.958,1.594 6.375,1.792 0.417,0.198 10 false KSW 4.094,1.833 4.406,2.031 0.313,0.198 10 false H1 0.917,1.76 1.208,1.958 0.292,0.198 10 false H21 3.885,0.104 6.219,0.594 2.333,0.49 10 false Front view of wire harness connector: (to Main Body ECU)

a.

Disconnect the H1 main body ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H1-5 (KSW) - H21-1 Always Below 1 Ω
H1-5 (KSW) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - BODY GROUND)
a.
U153462E02
0.802,1.479 1.115,1.677 0.313,0.198 10 false H21 0.146,0.094 2.458,0.635 2.313,0.542 10 false Front view of wire harness connector: (to Unlock Warning Switch)

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H21-2 - Body ground Always Below 1 Ω




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR