Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM
RM27L0U _55 Steering _049327 STEERING COLUMN _0235762 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM C

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  B2610  Tilt Position Sensor or Tilt Motor Circuit Malfunction  


DESCRIPTION

The tilt motor is operated by the power source voltage supplied from the multiplex tilt and telescopic ECU and tilts the steering column up and down. The tilt position sensor (Hall IC) in the tilt motor detects the tilt angle of the steering column and outputs a signal to the CPU based on that tilt.

C152160E14
1.031,0.167 2.24,0.51 1.208,0.344 10 false Tilt Up Mechanical Lock Position 4.865,0.156 6.375,0.573 1.51,0.417 10 false Tilt Down Mechanical Lock Position 2.969,1.875 4.115,2.073 1.146,0.198 10 false Operation Range 1.094,2.031 2.406,2.302 1.313,0.271 10 false Tilt Up Limit Position 4.573,2.031 6.135,2.281 1.563,0.25 10 false Tilt Down Limit Position

HINT:

Limit positions can be confirmed on the screen of the Techstream.


DTC Code Detection Condition Trouble Area
B2610 Tilt operation stops within the operation range while operating.
·

Harness or connector

·

Tilt position sensor or tilt motor

·

Multiplex tilt and telescopic ECU



WIRING DIAGRAM

C160342E04
0.948,4.135 1.26,4.333 0.313,0.198 10 false H58 0.906,0.979 1.635,1.188 0.729,0.208 10 false Tilt Motor 1.708,0.948 2.146,1.146 0.438,0.198 10 false TIM+ 4.646,0.938 5.063,1.135 0.417,0.198 10 false TIM+ 1.729,1.74 2.167,1.938 0.438,0.198 10 false TIM- 4.656,1.719 5.031,1.917 0.375,0.198 10 false TIM- 1.771,2.51 2.094,2.708 0.323,0.198 10 false VCI 4.656,2.49 4.979,2.688 0.323,0.198 10 false VCI 1.792,2.885 2.073,3.083 0.281,0.198 10 false TIS 4.656,2.865 4.938,3.063 0.281,0.198 10 false TIS 1.833,3.26 2.083,3.458 0.25,0.198 10 false E1 4.656,3.26 4.906,3.458 0.25,0.198 10 false E1 0.479,3.323 1.771,3.542 1.292,0.219 10 false Tilt Position Sensor 2.104,1.458 2.25,1.656 0.146,0.198 10 false 1 4.458,1.458 4.604,1.656 0.146,0.198 10 false 1 2.104,0.667 2.229,0.865 0.125,0.198 10 false 2 2.104,2.219 2.25,2.417 0.146,0.198 10 false 4 2.104,2.625 2.25,2.823 0.146,0.198 10 false 5 2.104,3 2.219,3.208 0.115,0.208 10 false 6 4.448,2.208 4.563,2.417 0.115,0.208 10 false 6 4.448,2.604 4.563,2.813 0.115,0.208 10 false 7 4.646,3.969 4.979,4.167 0.333,0.198 10 false H57 4.396,0.667 4.635,0.865 0.24,0.198 10 false 10 4.396,3.406 4.635,3.604 0.24,0.198 10 false 11 4.385,3 4.625,3.198 0.24,0.198 10 false 17 4.646,3.646 5.052,3.844 0.406,0.198 10 false GND 6,0.594 6.313,0.792 0.313,0.198 10 false +B 6,1.448 6.313,1.646 0.313,0.198 10 false +B 6.083,2.177 6.49,2.375 0.406,0.198 10 false 12 V 6.052,3.302 6.417,3.5 0.365,0.198 10 false CPU 4.646,4.146 6.792,4.344 2.146,0.198 10 false Multiplex Tilt and Telescopic ECU 0.948,4.302 1.677,4.5 0.729,0.198 10 false Tilt Motor

PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (TILT UP/DOWN)
C106468E01
1.992,0.035 2.232,0.236 0.239,0.201 10 Up 2.474,1.152 2.886,1.363 0.413,0.211 10 Down

a.

Select the Active Test, use the Techstream to generate a control command, and then check that the tilt up/down function operates normally.

Tilt & Telescopic
Tester Display Test Part Control Range Diagnostic Note
Tilt Operation Tilt operation Up / Down -


Result
Result Proceed to
Steering wheel does not tilt up (down). A
Steering wheel tilts up (down). B


A

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT MOTOR)

B

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT POSITION SENSOR)
2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT MOTOR)
U153419E02
1.927,2.021 1.563,2.24 false 1.927,2.094 1.563,2.51 false 4.708,2.115 4.875,2.594 true 4.448,2.052 4.198,1.729 false 0.615,0.083 2.938,0.563 2.323,0.479 10 false Rear view of wire harness connector: (to Multiplex Tilt and Telescopic ECU) 1.208,2.167 1.573,2.365 0.365,0.198 10 false TIM+ 3.844,1.625 4.271,1.823 0.427,0.198 10 false TIM+ 1.208,2.396 1.521,2.594 0.313,0.198 10 false TIM- 4.823,2.583 5.25,2.781 0.427,0.198 10 false TIM- 2.042,1.115 2.333,1.313 0.292,0.198 10 false H57 3.948,2.146 4.26,2.344 0.313,0.198 10 false H58 3.813,0.083 6.073,0.552 2.26,0.469 10 false Rear view of wire harness connector: (to Tilt Motor)

a.

Disconnect the H57 multiplex tilt and telescopic ECU connector.


b.

Disconnect the H58 tilt motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H57-10 (TIM+) - H58-2 (TIM+) Always Below 1 Ω
H57-1 (TIM-) - H58-1 (TIM-) Always Below 1 Ω
H57-10 (TIM+) - Body ground Always 10 kΩ or higher
H57-1 (TIM-) - Body ground Always 10 kΩ or higher




OK

3.INSPECT TILT MOTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT TILT MOTOR
a.
C179946E01
0.17,0.025 2.655,0.424 2.485,0.399 10 Component without harness connected: (Tilt Motor) 0.289,1.292 0.642,1.493 0.353,0.201 10 TIM+ 2.708,1.292 3.021,1.493 0.313,0.201 10 TIM- 1.304,1.408 0.74,1.408 false 2.696,1.408 2.132,1.408 false

Connect the positive (+) battery terminal to terminal 2 (TIM+) and the negative (-) battery terminal to terminal 1 (TIM-) of the tilt motor connector. Then confirm that the steering wheel tilts up.

OK:

The steering wheel tilts up.



b.

Connect the negative (-) battery terminal to terminal 2 (TIM+) and the positive (+) battery terminal to terminal 1 (TIM-) of the tilt motor connector. Then confirm that the steering wheel tilts down.

OK:

The steering wheel tilts down.




OK

NG

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT POSITION SENSOR)
U153420E02
2.198,2.104 2.708,2.563 false 2.24,2.104 2.708,2.302 false 2.302,2.031 2.708,1.969 false 4.448,2.219 4.063,2.51 true 4.521,2.219 4.385,2.51 true 4.635,2.219 4.896,2.51 true 0.635,0.271 2.958,0.76 2.323,0.49 10 false Rear view of wire harness connector: (to Multiplex Tilt and Telescopic ECU) 2.74,1.875 3.104,2.073 0.365,0.198 10 false E1 2.74,2.219 3.052,2.417 0.313,0.198 10 false TIS 2.031,1.104 2.323,1.302 0.292,0.198 10 false H57 3.948,1.948 4.26,2.146 0.313,0.198 10 false H58 3.813,0.271 6.063,0.792 2.25,0.521 10 false Rear view of wire harness connector: (to Tilt Motor) 2.74,2.469 3.052,2.667 0.313,0.198 10 false VCI 3.99,2.51 4.354,2.708 0.365,0.198 10 false E1 4.302,2.51 4.615,2.708 0.313,0.198 10 false TIS 4.792,2.51 5.104,2.708 0.313,0.198 10 false VCI

a.

Disconnect the H57 multiplex tilt and telescopic ECU connector.


b.

Disconnect the H58 tilt motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H57-6 (VCI) - H58-4 (VCI) Always Below 1 Ω
H57-7 (TIS) - H58-5 (TIS) Always Below 1 Ω
H57-17 (E1) - H58-6 (E1) Always Below 1 Ω
H57-6 (VCI) - Body ground Always 10 kΩ or higher
H57-7 (TIS) - Body ground Always 10 kΩ or higher
H57-17 (E1) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)
a.
U153413E02
1.854,2.594 1.26,3 true 0.104,0.104 2.469,0.552 2.365,0.448 10 false Rear view of wire harness connector: (to Multiplex Tilt and Telescopic ECU) 1.063,3.01 1.458,3.208 0.396,0.198 10 false GND 1.979,1.333 2.271,1.531 0.292,0.198 10 false H57

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H57-11 (GND) - Body ground Always Below 1 Ω




OK

6.INSPECT MULTIPLEX TILT AND TELESCOPIC ECU (VCI, TIS TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT MULTIPLEX TILT AND TELESCOPIC ECU (VCI, TIS TERMINAL VOLTAGE)
a.
U153421E02
0.833,2.531 0.281,2.99 true 0.979,2.542 0.698,3 true 1.125,2.542 1.521,3 true 0.146,0.146 2.406,0.552 2.26,0.406 10 false Rear view of wire harness connector: (to Tilt Motor) 0.208,2.177 0.49,2.375 0.281,0.198 10 false H58 1.385,3 1.708,3.198 0.323,0.198 10 false VCI 0.563,3 0.865,3.198 0.302,0.198 10 false TIS 0.167,3 0.417,3.198 0.25,0.198 10 false E1

Reconnect the H57 multiplex tilt and telescopic ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H58-4 (VCI) - H58-6 (E1) Ignition switch ON 8 to 16 V
H58-5 (TIS) - H58-6 (E1) Ignition switch ON 8 to 16 V




OK

7.INSPECT TILT POSITION SENSOR

NG

7.INSPECT TILT POSITION SENSOR
a.
U153417E02
2.302,2.073 2.854,2.646 true 2.854,1.729 2.375,2 true 2.906,1.573 3.156,1.771 0.25,0.198 10 false E1 2.906,2.531 3.219,2.729 0.313,0.198 10 false TIS 2.115,1.417 2.406,1.615 0.292,0.198 10 false H57 0.313,0.24 2.802,0.76 2.49,0.521 10 false Component with harness connected: (Multiplex Tilt and Telescopic ECU)

Reconnect the H58 tilt motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H57-7 (TIS) - H57-17 (E1) Steering tilts up or tilts down 8 to 16 V (Pulse HI)
Below 1 V (Pulse LOW)




OK

NG