Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM
RM27L0U _55 Steering _049327 STEERING COLUMN _0235762 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM C

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  B2611  Telescopic Position Sensor or Telescopic Motor Circuit Malfunction  


DESCRIPTION

The telescopic motor is operated by the power source voltage supplied from the multiplex tilt and telescopic ECU and slides the steering column forward and backward. The telescopic position sensor (Hall IC) in the telescopic motor detects the sliding position in the forward and backward directions of the steering column and outputs a signal to the multiplex tilt and telescopic ECU based on that sliding amount.

C152160E15
0.521,0.135 2.469,0.573 1.948,0.438 10 false Telescopic Steering Contracted Mechanical Lock Position 4.698,0.115 6.635,0.531 1.938,0.417 10 false Telescopic Steering Extended Mechanical Lock Position 0.906,1.969 2.604,2.365 1.698,0.396 10 false Telescopic Steering Contracted Limit Position 4.625,1.979 6.26,2.396 1.635,0.417 10 false Telescopic Steering Extended Limit Position 2.99,1.885 4.125,2.052 1.135,0.167 10 false Operation Range

HINT:

Limit positions can be confirmed on the screen of the Techstream.

DTC Code Detection Condition Trouble Area
B2611 Telescopic operation stops within the operation range while operating.
·

Harness or connector

·

Telescopic position sensor or telescopic motor

·

Multiplex tilt and telescopic ECU




WIRING DIAGRAM

C162229E04
0.698,1.021 1.927,1.229 1.229,0.208 10 false Telescopic Motor 4.646,0.938 5.063,1.135 0.417,0.198 10 false TEM+ 4.656,1.729 5.031,1.927 0.375,0.198 10 false TEM- 4.656,2.479 4.979,2.677 0.323,0.198 10 false VCE 4.656,2.875 4.99,3.073 0.333,0.198 10 false TES 4.656,3.271 4.906,3.469 0.25,0.198 10 false E2 0.479,3.375 1.771,3.781 1.292,0.406 10 false Telescopic Position Sensor 4.375,1.406 4.521,1.604 0.146,0.198 10 false 6 4.385,2.156 4.5,2.365 0.115,0.208 10 false 3 4.385,2.573 4.5,2.781 0.115,0.208 10 false 4 4.365,0.813 4.698,1.01 0.333,0.198 10 false A 4.365,1.604 4.698,1.802 0.333,0.198 10 false A 4.365,2.354 4.698,2.552 0.333,0.198 10 false A 4.375,2.75 4.708,2.948 0.333,0.198 10 false A 4.365,3.146 4.698,3.344 0.333,0.198 10 false A 4.292,3.563 4.625,3.76 0.333,0.198 10 false H57 4.385,0.604 4.625,0.802 0.24,0.198 10 false 2 4.344,3.344 4.583,3.542 0.24,0.198 10 false 11 4.385,2.969 4.625,3.167 0.24,0.198 10 false 5 4.646,3.667 5.052,3.865 0.406,0.198 10 false GND 6,0.563 6.313,0.76 0.313,0.198 10 false +B 6,1.385 6.313,1.583 0.313,0.198 10 false +B 6.083,2.156 6.49,2.354 0.406,0.198 10 false 12 V 6.052,3.302 6.406,3.5 0.354,0.198 10 false CPU 4.646,3.99 6.792,4.188 2.146,0.198 10 false Multiplex Tilt and Telescopic ECU 0.667,4.219 1.917,4.427 1.25,0.208 10 false Telescopic Motor

CAUTION / NOTICE / HINT

HINT:

The wire harness between the multiplex tilt and telescopic ECU and telescopic motor is provided with the steering column assembly.


PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (TELESCO LONG/SHORT)
C106469E04
1.052,0.104 1.531,0.302 0.479,0.198 10 false Extend 1.969,1.865 2.552,2.063 0.583,0.198 10 false Contract

a.

Select the Active Test, use the Techstream to generate a control command, and then check that the telesco long/short function operates normally.

Tilt & Telescopic
Tester Display Test Part Control Range Diagnostic Note
Telesco Operation Telescopic operation Long / Short -


Result
Result Proceed to
The steering column does not contract (extend). A
The steering column contracts (extends). B


A

2.INSPECT TELESCOPIC MOTOR

B

3.INSPECT MULTIPLEX TILT AND TELESCOPIC ECU (VCE TERMINAL VOLTAGE)
2.INSPECT TELESCOPIC MOTOR
a.
C149086E17
1.094,2.542 0.521,2.385 false 0.521,2.771 1.094,2.615 false 0.313,0.177 2.646,0.594 2.333,0.417 10 false Rear view of wire harness connector: (to Multiplex Tilt and Telescopic ECU) 0.76,1.083 1.719,1.281 0.958,0.198 10 false Connector A 0.104,2.26 0.583,2.458 0.479,0.198 10 false TEM+ 0.135,2.677 0.583,2.875 0.448,0.198 10 false TEM-

Disconnect connector A from the multiplex tilt and telescopic ECU.


b.

Connect the positive (+) battery terminal to terminal A-2 (TEM+) and the negative (-) battery terminal to terminal A-6 (TEM-) of the telescopic motor connector. Then confirm that the steering column contracts.

OK:

The steering column contracts.



c.

Connect the negative (-) battery terminal to terminal A-2 (TEM+) and the positive (+) battery terminal to terminal A-6 (TEM-) of the telescopic motor connector. Then confirm that the steering column extends.

OK:

The steering column extends.




OK

NG

3.INSPECT MULTIPLEX TILT AND TELESCOPIC ECU (VCE TERMINAL VOLTAGE)
a.
C149088E38
1.25,2.094 1.615,3.031 true 1.073,2.094 0.708,3.031 true 0.615,3.052 0.865,3.26 0.25,0.208 10 false E2 1.469,3.063 1.865,3.271 0.396,0.208 10 false VCE 0.646,1.333 1.448,1.542 0.802,0.208 10 false Connector A 0.271,0.25 2.76,0.646 2.49,0.396 10 false Component with harness connected: (Multiplex Tilt and Telescopic ECU)

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A-3 (VCE) - A-5 (E2) Ignition switch ON 8 to 16 V




OK

4.INSPECT TELESCOPIC POSITION SENSOR

NG

5.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TELESCOPIC POSITION SENSOR)
4.INSPECT TELESCOPIC POSITION SENSOR
a.
C149088E28
0.618,2.981 0.864,3.186 0.245,0.205 10 E2 1.385,2.981 1.780,3.187 0.395,0.206 10 TES 1.174,2.059 1.537,3.002 false 1.09,2.059 0.727,3.002 false 0.641,1.335 1.447,1.540 0.807,0.205 10 Connector A 0.131,0.059 2.617,0.458 2.486,0.399 10 Component with harness connected: (Multiplex Tilt and Telescopic ECU)

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A-4 (TES) - A-5 (E2) Telescopic steering contracted or extended 8 to 16 V (Pulse HI)
Below 1 V (Pulse LOW)




OK

NG

5.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TELESCOPIC POSITION SENSOR)
a.
C149086E18
1.906,2.771 1.333,2.615 true 0.229,0.198 2.552,0.688 2.323,0.49 10 false Rear view of wire harness connector: (to Multiplex Tilt and Telescopic ECU) 0.76,1.083 1.719,1.281 0.958,0.198 10 false Connector A 1.969,2.698 2.417,2.896 0.448,0.198 10 false VCE

Disconnect connector A from the multiplex tilt and telescopic ECU.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-3 (VCE) - Body ground Always 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)
a.
U153413E02
1.854,2.594 1.26,3 true 0.104,0.104 2.469,0.552 2.365,0.448 10 false Rear view of wire harness connector: (to Multiplex Tilt and Telescopic ECU) 1.063,3.01 1.458,3.208 0.396,0.198 10 false GND 1.979,1.333 2.271,1.531 0.292,0.198 10 false H57

Disconnect the H57 multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H57-11 (GND) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR