Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049331 PARK ASSIST / MONITORING _0235792 BLIND SPOT MONITOR SYSTEM J

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the blind spot monitor sensors.

WIRING DIAGRAM

E224413E22
3.615,0.708 3.927,0.885 0.313,0.177 10 false BLB 3.438,0.604 3.552,0.781 0.115,0.177 10 false 5 3.625,3.302 3.938,3.479 0.313,0.177 10 false BRB 3.458,3.198 3.573,3.375 0.115,0.177 10 false 5 3.625,4.073 4.063,4.25 0.438,0.177 10 false BRGD 3.458,3.979 3.573,4.156 0.115,0.177 10 false 1 3.438,1.396 3.552,1.573 0.115,0.177 10 false 1 3.615,1.5 4.042,1.656 0.427,0.156 10 false BLGD 1.656,0.885 2.531,1.052 0.875,0.167 10 false ECU-IG No.1 0.375,0.729 1.24,1.188 0.865,0.458 10 false from IG No.1 Relay 3.417,2.042 3.781,2.198 0.365,0.156 10 false O46 3.417,2.219 4.563,2.563 1.146,0.344 10 false Blind Spot Monitor Sensor LH 3.469,4.802 4.635,5.146 1.167,0.344 10 false Blind Spot Monitor Sensor RH 0.885,5.323 2.802,5.479 1.917,0.156 10 false : CAN Communication Line 3.469,4.635 3.875,4.792 0.406,0.156 10 false P25 6.083,1.083 6.969,1.448 0.885,0.365 10 true to Network Gateway ECU

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING TECHSTREAM
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Data List.


e.

According to the display on the Techstream, read the Data List.

Blind Spot Monitor Master
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Power Supply Voltage Power supply voltage / Min.: 0 V, Max.: 50 V 11 to 14 V -

Blind Spot Monitor Slave
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Power Supply Voltage Power supply voltage / Min.: 0 V, Max.: 50 V 11 to 14 V -

Result
Result Proceed to
The power supply voltages of the master and slave side sensors of the blind spot monitor system are both normal. A
The power supply voltage of the master side sensor of the blind spot monitor system is abnormal. B
The power supply voltage of the slave side sensor of the blind spot monitor system is abnormal. C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BATTERY)

C

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BATTERY)
2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BATTERY)
a.

Disconnect the P25 blind spot monitor sensor RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
P25-5 (BRB) - Body ground Ignition switch ON 11 to 14 V
P25-5 (BRB) - Body ground Ignition switch off Below 1 V




OK

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BODY GROUND)
a.

Disconnect the P25 blind spot monitor sensor RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P25-1 (BRGD) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BATTERY)
a.

Disconnect the O46 blind spot monitor sensor LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O46-5 (BLB) - Body ground Ignition switch ON 11 to 14 V
O46-5 (BLB) - Body ground Ignition switch off Below 1 V




OK

5.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BODY GROUND)
a.

Disconnect the O46 blind spot monitor sensor LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O46-1 (BLGD) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR