Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049331 PARK ASSIST / MONITORING _0235792 BLIND SPOT MONITOR SYSTEM J

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  Main Switch Circuit  


DESCRIPTION

When the blind spot monitor main switch assembly (warning canceling switch assembly) is turned on, a signal is sent to the blind spot monitor sensor RH. The blind spot monitor system operates according to this signal.

WIRING DIAGRAM

E224414E25
5.438,0.635 6.115,0.802 0.677,0.167 10 false BSSW 5.26,0.521 5.365,0.698 0.104,0.177 10 false 3 4.479,0.521 4.583,0.698 0.104,0.177 10 false 8 4.313,0.729 4.458,0.906 0.146,0.177 10 false D 3.521,0.729 3.667,0.906 0.146,0.177 10 false B 3.292,0.521 3.479,0.698 0.188,0.177 10 false 11 5.313,1.938 5.74,2.083 0.427,0.146 10 false P25 5.313,2.104 7.031,2.448 1.719,0.344 10 false Blind Spot Monitor Sensor RH 2.219,0.792 3.104,0.948 0.885,0.156 10 false ECU-IG No.1 0.365,0.625 1.656,0.802 1.292,0.177 10 false from IG No.1 Relay 3.365,0.958 3.833,1.115 0.469,0.156 10 false H121 3.354,1.125 5.208,1.896 1.854,0.771 10 false Blind Spot Monitor Main Switch Assembly (Warning Canceling Switch Assembly)

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuse for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING TECHSTREAM
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Blind Spot Monitor Master / Data List.


e.

According to the display on the Techstream, read the Data List.

Blind Spot Monitor Master
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
BSM Main SW Blind spot monitor main switch assembly (warning canceling switch assembly) / OFF or ON ON: Blind spot monitor main switch assembly (warning canceling switch assembly) on
OFF: Blind spot monitor main switch assembly (warning canceling switch assembly) off
-

Result
Result Proceed to
The display changes as shown above when the blind spot monitor main switch assembly (warning canceling switch assembly) is operated. A
The display does not change as shown above when the blind spot monitor main switch assembly (warning canceling switch assembly) is operated. B



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT BLIND SPOT MONITOR MAIN SWITCH ASSEMBLY (WARNING CANCELING SWITCH ASSEMBLY)
2.INSPECT BLIND SPOT MONITOR MAIN SWITCH ASSEMBLY (WARNING CANCELING SWITCH ASSEMBLY)
a.
E224422E08
1.497,1.454 1.171,1.947 1.171,1.947 0.93,1.947 false 1.961,1.454 2.288,1.947 2.288,1.947 2.529,1.947 false 2.569,1.855 2.697,2.016 0.128,0.161 10 D 0.793,1.856 0.921,2.016 0.128,0.161 10 B

Remove the blind spot monitor main switch assembly (warning canceling switch assembly) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR MAIN SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
11 (B) - 8 (D) Blind spot monitor main switch is on Below 1 Ω
11 (B) - 8 (D) Blind spot monitor main switch is off 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BATTERY)

NG

REPLACE BLIND SPOT MONITOR MAIN SWITCH ASSEMBLY (WARNING CANCELING SWITCH ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BATTERY)
a.

Disconnect the H121 blind spot monitor main switch assembly (warning canceling switch assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H121-11 (B) - Body ground Ignition switch ON 11 to 14 V
H121-11 (B) - Body ground Ignition switch off Below 1 V




OK

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BLIND SPOT MONITOR SENSOR RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BLIND SPOT MONITOR SENSOR RH)
a.

Disconnect the P25 blind spot monitor sensor RH connector.


b.

Disconnect the H121 blind spot monitor main switch assembly (warning canceling switch assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P25-3 (BSSW) - H121-8 (D) Always Below 1 Ω
P25-3 (BSSW) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR