Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM27L0U _57 Power Source / Network _049335 NETWORKING _0235802 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U1002  Lost Communication with Gateway Module  


DESCRIPTION

·

The main body ECU stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the CAN MS bus.

·

When the main body ECU receives a response signal from the ECUs connected to the CAN MS bus, the main body ECU recognizes and memorizes that the ECU is connected to the CAN MS bus. Based on this memorized data, the main body ECU monitors for malfunctions in the ECUs connected to the CAN MS bus when communicating with those ECUs. If the main body ECU cannot receive response signals from the ECUs that have been memorized as those connected to the CAN MS bus, the main body ECU determines that a malfunction exists.

·

If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).


DTC Code DTC Detection Condition Trouble Area
U1002 Lost communication with the gateway module (MS bus).
·

MS bus circuit

·

Front power seat switch LH (power seat control ECU) CAN branch wire or connector

·

Multiplex tilt and telescopic ECU CAN branch wire or connector

·

Outer mirror control ECU assembly CAN branch wire or connector

·

Power back door unit assembly (power back door ECU) CAN branch wire or connector*

·

Combination meter assembly CAN main wire or connector

·

Main body ECU (cowl side junction block LH) CAN main wire or connector

·

Front power seat switch LH (power seat control ECU)

·

Multiplex tilt and telescopic ECU

·

Outer mirror control ECU assembly

·

Combination meter assembly

·

Main body ECU (cowl side junction block LH)

·

Power back door unit assembly (power back door ECU)*

·

No. 3 junction connector

·

No. 4 junction connector*



*: w/ Power Back Door System

For vehicle with an seat memory.


WIRING DIAGRAM

C244516E02
5.6,1.16 6.034,1.298 0.434,0.139 10 CANL 5.6,0.606 6.034,0.745 0.434,0.139 10 CANH 5.308,0.988 5.496,1.127 0.187,0.139 10 21 5.308,0.606 5.496,0.745 0.187,0.139 10 22 5.4,1.408 5.692,1.557 0.291,0.149 10 H37 5.4,1.541 6.688,1.847 1.288,0.305 10 Combination Meter Assembly 5.298,3.141 5.589,3.290 0.291,0.149 10 X11 5.298,3.274 7.079,3.579 1.781,0.305 10 Front Power Seat Switch LH (Power Seat Control ECU) 0.604,1.408 0.895,1.557 0.291,0.149 10 H57 0.604,1.541 2.350,1.847 1.746,0.305 10 Multiplex Tilt and Telescopic ECU 2.909,4.855 3.274,5.004 0.365,0.149 10 H116 2.909,5.009 4.507,5.158 1.598,0.149 10 No. 3 Junction Connector 2.909,8.022 4.507,8.171 1.598,0.149 10 No. 4 Junction Connector 0.604,3.123 0.895,3.272 0.291,0.149 10 M8 0.604,3.257 2.350,3.562 1.746,0.305 10 Outer Mirror Control ECU Assembly 1.919,6.168 2.106,6.306 0.187,0.139 10 5 1.919,5.593 2.027,5.732 0.108,0.139 10 6 1.367,6.25 1.778,6.388 0.412,0.139 10 CANN 1.37,5.675 1.778,5.814 0.408,0.139 10 CANP 0.604,6.582 0.895,6.731 0.291,0.149 10 O30 0.604,6.715 2.642,7.021 2.038,0.305 10 Power Back Door Unit Assembly (Power Back Door ECU) 3.984,0.988 4.172,1.127 0.187,0.139 10 12 3.984,0.606 4.093,0.745 0.108,0.139 10 1 3.098,0.988 3.285,1.127 0.187,0.139 10 13 3.178,0.606 3.286,0.745 0.108,0.139 10 2 1.919,0.988 2.106,1.127 0.187,0.139 10 14 1.919,0.606 2.027,0.745 0.108,0.139 10 5 1.386,1.074 1.778,1.212 0.392,0.139 10 CANL 1.363,0.688 1.778,0.827 0.415,0.139 10 CANH 3.984,2.702 4.172,2.840 0.187,0.139 10 14 3.984,2.32 4.093,2.459 0.108,0.139 10 3 3.984,4.411 4.172,4.550 0.187,0.139 10 15 3.984,4.029 4.093,4.168 0.108,0.139 10 4 3.098,2.702 3.285,2.840 0.187,0.139 10 16 3.178,2.32 3.286,2.459 0.108,0.139 10 5 5.391,2.702 5.496,2.840 0.106,0.139 10 1 5.388,2.32 5.496,2.459 0.108,0.139 10 5 5.6,2.787 6.029,2.926 0.429,0.139 10 CANL 5.6,2.402 6.034,2.541 0.434,0.139 10 CANH 5.6,7.724 6.029,7.863 0.429,0.139 10 CANN 5.6,6.956 6.034,7.095 0.434,0.139 10 CANP 1.919,2.702 2.106,2.840 0.187,0.139 10 21 1.919,2.32 2.027,2.459 0.108,0.139 10 1 1.349,2.787 1.778,2.926 0.429,0.139 10 CGND 1.461,2.402 1.779,2.541 0.318,0.139 10 CAN 0.083,0.082 2.295,0.286 2.211,0.205 12 w/ Power Back Door System: 3.981,7.053 4.261,7.190 0.280,0.137 10 O41 4.074,6.822 4.170,6.961 0.097,0.139 10 5 3.981,7.629 4.261,7.766 0.280,0.137 10 O41 4.034,7.41 4.209,7.550 0.176,0.140 10 11 3.981,5.685 4.261,5.821 0.280,0.137 10 O41 4.074,5.454 4.170,5.593 0.097,0.139 10 6 3.981,6.261 4.261,6.398 0.280,0.137 10 O41 4.034,6.042 4.209,6.182 0.176,0.140 10 12 2.996,5.685 3.276,5.821 0.280,0.137 10 O42 3.088,5.454 3.185,5.593 0.097,0.139 10 1 2.996,6.261 3.276,6.398 0.280,0.137 10 O42 3.086,6.042 3.187,6.182 0.102,0.140 10 7 5.32,6.964 5.496,7.103 0.176,0.139 10 16 5.32,7.54 5.496,7.680 0.176,0.140 10 15 5.204,7.947 5.496,8.096 0.291,0.149 10 H2 5.204,8.08 6.958,8.386 1.754,0.305 10 Main Body ECU (Cowl Side Junction Block LH)

C244517E02
5.6,1.202 6.034,1.340 0.434,0.139 10 CANL 5.6,0.648 6.034,0.787 0.434,0.139 10 CANH 5.308,1.03 5.496,1.169 0.187,0.139 10 21 5.308,0.648 5.496,0.787 0.187,0.139 10 22 2.909,4.897 3.274,5.046 0.365,0.149 10 H116 2.909,5.051 4.507,5.200 1.598,0.149 10 No. 3 Junction Connector 0.604,3.165 0.895,3.314 0.291,0.149 10 M8 0.604,3.299 2.350,3.604 1.746,0.305 10 Outer Mirror Control ECU Assembly 3.984,1.03 4.172,1.169 0.187,0.139 10 12 3.984,0.648 4.093,0.787 0.108,0.139 10 1 3.098,1.03 3.285,1.169 0.187,0.139 10 13 3.178,0.648 3.286,0.787 0.108,0.139 10 2 1.919,1.03 2.106,1.169 0.187,0.139 10 14 1.919,0.648 2.027,0.787 0.108,0.139 10 5 1.386,1.116 1.778,1.254 0.392,0.139 10 CANL 1.363,0.73 1.778,0.869 0.415,0.139 10 CANH 3.984,2.744 4.172,2.883 0.187,0.139 10 14 3.984,2.362 4.093,2.501 0.108,0.139 10 3 3.984,4.471 4.172,4.609 0.187,0.139 10 15 3.984,4.094 4.093,4.232 0.108,0.139 10 4 3.098,2.744 3.285,2.883 0.187,0.139 10 16 3.178,2.362 3.286,2.501 0.108,0.139 10 5 5.391,2.744 5.496,2.883 0.106,0.139 10 1 5.388,2.362 5.496,2.501 0.108,0.139 10 5 5.6,2.83 6.029,2.968 0.429,0.139 10 CANL 5.6,2.444 6.034,2.583 0.434,0.139 10 CANH 5.6,4.653 6.029,4.791 0.429,0.139 10 CANN 5.6,4.094 6.034,4.232 0.434,0.139 10 CANP 1.919,2.744 2.106,2.883 0.187,0.139 10 21 1.919,2.362 2.027,2.501 0.108,0.139 10 1 1.349,2.83 1.778,2.968 0.429,0.139 10 CGND 1.461,2.444 1.779,2.583 0.318,0.139 10 CAN 0.083,0.124 2.378,0.328 2.295,0.205 12 w/o Power Back Door System: 5.324,4.094 5.496,4.234 0.172,0.141 10 16 5.315,4.471 5.496,4.609 0.180,0.138 10 15 5.204,4.881 5.496,5.030 0.291,0.149 10 H2 5.204,5.015 6.958,5.320 1.754,0.305 10 Main Body ECU (Cowl Side Junction Block LH) 5.4,1.45 5.692,1.599 0.291,0.149 10 H37 5.4,1.583 6.688,1.889 1.288,0.305 10 Combination Meter Assembly 5.298,3.183 5.589,3.332 0.291,0.149 10 X11 5.298,3.316 7.079,3.621 1.781,0.305 10 Front Power Seat Switch LH (Power Seat Control ECU) 0.604,1.45 0.895,1.599 0.291,0.149 10 H57 0.604,1.583 2.350,1.889 1.746,0.305 10 Multiplex Tilt and Telescopic ECU

CAUTION / NOTICE / HINT

HINT:

Operating the ignition switch, any other switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistance of the CAN main wire or CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK CAN BUS WIRE (CHECK MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT)
3.CHECK CAN BUS WIRE (CHECK MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT)
a.
U153883E01
0.069,0.049 0.288,0.246 0.218,0.198 10 *a 1.594,0.321 1.868,0.463 0.274,0.142 10 H37 2.598,1.135 2.729,1.387 2.729,1.387 2.882,1.387 false 2.564,1.656 2.456,1.656 2.456,1.656 2.507,1.135 false 1.071,1.009 0.828,0.549 0.828,0.549 0.705,0.549 false 0.892,1.136 0.673,1.467 0.673,1.467 0.581,1.467 false 2.894,1.314 3.298,1.456 0.404,0.142 10 CANL 2.567,1.58 2.994,1.722 0.427,0.142 10 CANH 0.361,1.383 0.549,1.525 0.189,0.142 10 E1 0.565,0.465 0.689,0.607 0.125,0.142 10 B

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition Resistance of Malfunction
H37-22 (CANH) - H37-21 (CANL) Ignition switch off 54 to 69 Ω Below 53 Ω : Short in line
H37-22 (CANH) - H37-21 (CANL) Ignition switch off 54 to 69 Ω 70 Ω or higher: Open in CAN main bus line
H37-22 (CANH) - H37-18 (B) Ignition switch off 6 kΩ higher Below 6 kΩ : +B short
H37-21 (CANL) - H37-18 (B) Ignition switch off 6 kΩ higher Below 6 kΩ : +B short
H37-22 (CANH) - H37-40 (E1) Ignition switch off 200 Ω or higher Below 200 Ω : Ground short
H37-21 (CANL) - H37-40 (E1) Ignition switch off 200 Ω or higher Below 200 Ω : Ground short


Text in Illustration
*a Component with harness connected
(to Combination Meter Assembly)

Result
Result Proceed to
NG
·

Open in CAN main bus line


A
NG (w/ Power Back Door System)
·

Short in line

·

+B short

·

GND short


B
NG (w/o Power Back Door System)
·

Short in line

·

+B short

·

GND short


C
OK D



A

4.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)

B

15.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR SIDE)

C

24.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - FRONT POWER SEAT SWITCH LH)

D

39.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
4.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)
a.
U153885E01
1.946,1.417 2.39,1.866 2.39,1.866 2.572,1.866 false 1.946,1.199 2.39,0.75 2.39,0.75 2.572,0.75 false 0.407,1.236 0.761,1.377 0.354,0.140 10 H116 2.59,0.674 3.051,0.814 0.460,0.140 10 CANH 2.59,1.791 3.051,1.931 0.460,0.140 10 CANL 0.061,0.049 0.415,0.190 0.354,0.140 10 *a

Disconnect the H116 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H116-4 (CANH) - H116-15 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)

Result
Result Proceed to
OK A
NG (w/o Power Back Door System) B
NG (w/ Power Back Door System) C



A

5.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

B

8.CONNECT CONNECTOR

C

10.CONNECT CONNECTOR
5.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.
U153886E01
2.272,1.417 2.474,1.624 2.474,1.624 2.657,1.624 false 2.272,1.199 2.467,0.999 2.467,0.999 2.65,0.999 false 0.407,1.23 0.761,1.370 0.354,0.140 10 H116 2.668,0.923 3.128,1.063 0.460,0.140 10 CANH 2.675,1.549 3.135,1.689 0.460,0.140 10 CANL 0.061,0.049 0.415,0.190 0.354,0.140 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H116-1 (CANH) - H116-12 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

REPLACE NO. 3 JUNCTION CONNECTOR

NG

6.CONNECT CONNECTOR
6.CONNECT CONNECTOR
a.

Reconnect the H116 No. 3 junction connector.



NEXT

7.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY - NO. 3 JUNCTION CONNECTOR)
7.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY - NO. 3 JUNCTION CONNECTOR)
a.
U153826E01
2.558,1.232 2.696,1.445 2.696,1.445 2.813,1.445 false 2.463,1.232 2.581,1.79 2.581,1.79 2.698,1.79 false 2.704,1.72 3.124,1.862 0.420,0.142 10 CANH 2.827,1.365 3.226,1.507 0.399,0.142 10 CANL 0.08,0.05 0.500,0.192 0.420,0.142 10 *a 1.556,0.226 1.836,0.368 0.281,0.142 10 H37

Disconnect the H37 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H37-22 (CANH) - H37-21 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Combination Meter Assembly)



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (COMBINATION METER ASSEMBLY - NO. 3 JUNCTION CONNECTOR)

8.CONNECT CONNECTOR
a.

Reconnect the H116 No. 3 junction connector.



NEXT

9.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU - NO. 3 JUNCTION CONNECTOR)
9.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU - NO. 3 JUNCTION CONNECTOR)
a.
U153838E01
2.05,1.533 2.305,1.928 2.305,1.928 2.443,1.928 false 1.934,1.533 1.679,1.928 1.679,1.928 1.541,1.928 false 2.469,1.853 2.891,1.989 0.422,0.137 10 CANP 1.021,1.853 1.443,1.989 0.422,0.137 10 CANN 0.693,1.161 0.892,1.298 0.199,0.137 10 H2 0.067,0.048 0.267,0.185 0.199,0.137 10 *a

Disconnect the H2 main body ECU (cowl side junction block LH) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H2-16 (CANP) - H2-15 (CANN) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Main Body ECU [Cowl Side Junction Block LH])



OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (MAIN BODY ECU - NO. 3 JUNCTION CONNECTOR)

10.CONNECT CONNECTOR
a.

Reconnect the H116 No. 3 junction connector.



NEXT

11.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
11.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
a.
U153833E01
0.467,0.844 0.947,0.981 0.480,0.137 10 CANH 2.581,1.12 2.867,1.258 0.286,0.137 10 O41 0.08,0.041 0.532,0.179 0.452,0.137 10 *a 0.444,1.419 0.924,1.557 0.480,0.137 10 CANL 0.997,0.932 1.083,0.932 1.083,0.932 1.233,1.07 false 1.237,1.302 0.98,1.508 0.98,1.508 0.908,1.508 false

Disconnect the O41 No. 4 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
O41-6 (CANH) - O41-12 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 4 Junction Connector)



OK

12.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - MAIN BODY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

12.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - MAIN BODY ECU)
a.
U153834E02
1.031,0.698 1.115,0.698 1.115,0.698 1.469,1.031 true 1.469,1.333 1.073,1.688 1.073,1.688 0.917,1.688 true 0.521,0.625 0.979,0.833 0.458,0.208 10 false CANH 2.563,1.115 2.938,1.344 0.375,0.229 10 false O41 0.083,0.042 0.656,0.406 0.573,0.365 10 false *a 0.51,1.615 0.906,1.917 0.396,0.302 10 true CANL

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
O41-5 (CANH) - O41-11 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 4 Junction Connector)



OK

REPLACE NO. 4 JUNCTION CONNECTOR

NG

13.CONNECT CONNECTOR
13.CONNECT CONNECTOR
a.

Reconnect the O41 No. 4 junction connector.



NEXT

14.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU - NO. 4 JUNCTION CONNECTOR)
14.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU - NO. 4 JUNCTION CONNECTOR)
a.
U153838E01
2.05,1.533 2.305,1.928 2.305,1.928 2.443,1.928 false 1.934,1.533 1.679,1.928 1.679,1.928 1.541,1.928 false 2.469,1.853 2.891,1.989 0.422,0.137 10 CANP 1.021,1.853 1.443,1.989 0.422,0.137 10 CANN 0.693,1.161 0.892,1.298 0.199,0.137 10 H2 0.067,0.048 0.267,0.185 0.199,0.137 10 *a

Disconnect the H2 main body ECU (cowl side junction block LH) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H2-16 (CANP) - H2-15 (CANN) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Main Body ECU [Cowl Side Junction Block LH])



OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (MAIN BODY ECU - NO. 4 JUNCTION CONNECTOR)

15.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR SIDE)
a.
U153884E01
0.069,0.049 0.288,0.246 0.218,0.198 10 *a 1.594,0.321 1.868,0.463 0.274,0.142 10 H37 2.598,1.135 2.729,1.387 2.729,1.387 2.882,1.387 false 2.564,1.656 2.456,1.656 2.456,1.656 2.507,1.135 false 1.071,1.009 0.828,0.549 0.828,0.549 0.705,0.549 false 0.892,1.136 0.673,1.467 0.673,1.467 0.581,1.467 false 2.894,1.314 3.298,1.456 0.404,0.142 10 CANL 2.567,1.58 2.994,1.722 0.427,0.142 10 CANH 0.361,1.383 0.549,1.525 0.189,0.142 10 E1 0.565,0.465 0.689,0.607 0.125,0.142 10 B

Disconnect the O41 No. 4 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H37-22 (CANH) - H37-21 (CANL) Ignition switch off 108 to 132 Ω
H37-22 (CANH) - H37-40 (E1) Ignition switch off 200 Ω or higher
H37-21 (CANL) - H37-40 (E1) Ignition switch off 200 Ω or higher
H37-22 (CANH) - H37-18 (B) Ignition switch off 6 kΩ or higher
H37-21 (CANL) - H37-18 (B) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Component with harness connected
(to Combination Meter Assembly)



OK

16.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - POWER BACK DOOR ECU)

NG

22.CONNECT CONNECTOR
16.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - POWER BACK DOOR ECU)
a.
U153856E01
1.673,2.512 1.488,2.164 1.488,2.164 1.348,2.164 false 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 2.082,1.308 2.249,1.447 2.249,1.447 2.346,1.447 false 2.315,0.963 2.243,0.963 2.243,0.963 2.082,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.337,0.885 2.757,1.027 0.420,0.142 10 CANH 2.373,1.361 2.796,1.503 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.405,2.696 0.691,2.835 0.286,0.140 10 H19 0.605,1.127 0.891,1.267 0.286,0.140 10 O42 1.062,2.087 1.291,2.229 0.229,0.142 10 CG

Disconnect the O42 No. 4 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
O42-1 (CANH) - O42-7 (CANL) Ignition switch off 200 Ω or higher
O42-1 (CANH) - H19-4 (CG) Ignition switch off 200 Ω or higher
O42-7 (CANL) - H19-4 (CG) Ignition switch off 200 Ω or higher
O42-1 (CANH) - H19-16 (BAT) Ignition switch off 6 kΩ or higher
O42-7 (CANL) - H19-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 4 Junction Connector)
*b Front view of DLC3



OK

17.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - MAIN BODY ECU)

NG

18.CONNECT CONNECTOR
17.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - MAIN BODY ECU)
a.
U153857E02
1.677,2.51 1.49,2.167 1.49,2.167 1.344,2.167 true 2.208,2.958 2.344,3.208 2.344,3.208 2.49,3.208 true 1.146,0.76 1.219,0.76 1.219,0.76 1.5,1.104 true 1.5,1.313 1.156,1.542 1.156,1.542 1.021,1.542 true 0.042,0.063 0.281,0.302 0.24,0.24 10 false *a 0.042,1.896 0.281,2.135 0.24,0.24 10 false *b 0.646,0.688 1.063,0.833 0.417,0.146 10 false CANH 2.521,3.135 2.948,3.281 0.427,0.146 10 false BAT 0.448,2.698 0.792,2.885 0.344,0.188 10 false H19 2.438,1.135 2.854,1.333 0.417,0.198 10 false O41 1.063,2.083 1.292,2.229 0.229,0.146 10 false CG 0.563,1.448 1,1.771 0.438,0.323 10 true CANL

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
O41-5 (CANH) - O41-11 (CANL) Ignition switch off 108 to 132 Ω
O41-5 (CANH) - H19-4 (CG) Ignition switch off 200 Ω or higher
O41-11 (CANL) - H19-4 (CG) Ignition switch off 200 Ω or higher
O41-5 (CANH) - H19-16 (BAT) Ignition switch off 6 kΩ or higher
O41-11 (CANL) - H19-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 4 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 4 JUNCTION CONNECTOR

NG

20.CONNECT CONNECTOR
18.CONNECT CONNECTOR
a.

Reconnect the O41 and O42 No. 4 junction connectors.



NEXT

19.CHECK FOR SHORT IN CAN BUS WIRES (POWER BACK DOOR ECU)
19.CHECK FOR SHORT IN CAN BUS WIRES (POWER BACK DOOR ECU)
a.
U153887E01
1.673,2.512 1.488,2.164 1.488,2.164 1.348,2.164 false 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 1.556,1.17 1.183,1.653 1.183,1.653 1.086,1.653 false 1.672,1.17 2.045,1.653 2.045,1.653 2.142,1.653 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.168,1.567 2.592,1.709 0.424,0.142 10 CANP 0.57,1.567 0.994,1.709 0.424,0.142 10 CANN 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.405,2.696 0.691,2.835 0.286,0.140 10 H19 0.184,1.007 0.469,1.147 0.286,0.140 10 O30 1.062,2.087 1.291,2.229 0.229,0.142 10 CG

Disconnect the O30 power back door unit assembly (power back door ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
O30-6 (CANP) - O30-5 (CANN) Ignition switch off 54 to 69 Ω
O30-6 (CANP) - H19-4 (CG) Ignition switch off 200 Ω or higher
O30-5 (CANN) - H19-4 (CG) Ignition switch off 200 Ω or higher
O30-6 (CANP) - H19-16 (BAT) Ignition switch off 6 kΩ or higher
O30-5 (CANN) - H19-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Power Back Door Unit Assembly [Power Back Door ECU])
*b Front view of DLC3



OK

REPLACE POWER BACK DOOR UNIT ASSEMBLY (POWER BACK DOOR ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER BACK DOOR ECU (CANP, CANN)

20.CONNECT CONNECTOR
a.

Reconnect the O41 and O42 No. 4 junction connectors.



NEXT

21.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
21.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
a.
U153866E01
1.673,2.512 1.488,2.164 1.488,2.164 1.348,2.164 false 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 2.005,1.457 2.172,1.596 2.172,1.596 2.269,1.596 false 2.236,1.11 2.164,1.11 2.164,1.11 1.89,1.364 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.258,1.033 2.678,1.175 0.420,0.142 10 CANN 2.295,1.51 2.719,1.652 0.424,0.142 10 CANP 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.405,2.696 0.691,2.835 0.286,0.140 10 H19 1.062,2.087 1.291,2.229 0.229,0.142 10 CG 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.668,1.129 0.863,1.268 0.195,0.140 10 H2

Disconnect the H2 main body ECU (cowl side junction block LH) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H2-16 (CANP) - H2-15 (CANN) Ignition switch off 108 to 132 Ω
H2-16 (CANP) - H19-4 (CG) Ignition switch off 200 Ω or higher
H2-15 (CANN) - H19-4 (CG) Ignition switch off 200 Ω or higher
H2-16 (CANP) - H19-16 (BAT) Ignition switch off 6 kΩ or higher
H2-15 (CANN) - H19-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Main Body ECU [Cowl Side Junction Block LH])
*b Front view of DLC3



OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (CANP, CANN)

22.CONNECT CONNECTOR
a.

Reconnect the O41 No. 4 junction connector.



NEXT

23.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
23.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
a.
U153794E01
1.673,2.512 1.488,2.164 1.488,2.164 1.348,2.164 false 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 1.932,1.291 2.305,1.597 2.305,1.597 2.402,1.597 false 2.381,0.746 2.31,0.746 2.31,0.746 1.932,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.403,0.668 2.823,0.810 0.420,0.142 10 CANH 2.428,1.511 2.852,1.653 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.405,2.696 0.691,2.835 0.286,0.140 10 H19 0.452,1.122 0.803,1.261 0.351,0.140 10 H116 1.062,2.087 1.291,2.229 0.229,0.142 10 CG

Disconnect the H116 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H116-4 (CANH) - H116-15 (CANL) Ignition switch off 108 to 132 Ω
H116-4 (CANH) - H19-4 (CG) Ignition switch off 200 Ω or higher
H116-15 (CANL) - H19-4 (CG) Ignition switch off 200 Ω or higher
H116-4 (CANH) - H19-16 (BAT) Ignition switch off 6 kΩ or higher
H116-15 (CANL) - H19-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

24.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - FRONT POWER SEAT SWITCH LH)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)

24.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - FRONT POWER SEAT SWITCH LH)
a.
U153795E01
1.673,2.512 1.488,2.164 1.488,2.164 1.348,2.164 false 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 2.026,1.291 2.217,1.569 2.217,1.569 2.314,1.569 false 2.439,0.837 2.368,0.837 2.368,0.837 2.026,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.461,0.759 2.881,0.901 0.420,0.142 10 CANH 2.34,1.483 2.764,1.625 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.405,2.696 0.691,2.835 0.286,0.140 10 H19 0.452,1.122 0.803,1.261 0.351,0.140 10 H116 1.062,2.087 1.291,2.229 0.229,0.142 10 CG

w/o Power Back Door System:

Disconnect the H116 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H116-3 (CANH) - H116-14 (CANL) Ignition switch off 200 Ω or higher
H116-3 (CANH) - H19-4 (CG) Ignition switch off 200 Ω or higher
H116-14 (CANL) - H19-4 (CG) Ignition switch off 200 Ω or higher
H116-3 (CANH) - H19-16 (BAT) Ignition switch off 6 kΩ or higher
H116-14 (CANL) - H19-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

25.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)

NG

29.CONNECT CONNECTOR
25.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)
a.
U153796E01
1.673,2.512 1.488,2.164 1.488,2.164 1.348,2.164 false 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 2.112,1.291 2.361,1.511 2.361,1.511 2.458,1.511 false 2.431,0.877 2.359,0.877 2.359,0.877 2.112,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.453,0.799 2.873,0.941 0.420,0.142 10 CANH 2.484,1.425 2.908,1.567 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.405,2.696 0.691,2.835 0.286,0.140 10 H19 0.452,1.122 0.803,1.261 0.351,0.140 10 H116 1.062,2.087 1.291,2.229 0.229,0.142 10 CG

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H116-2 (CANH) - H116-13 (CANL) Ignition switch off 200 Ω or higher
H116-2 (CANH) - H19-4 (CG) Ignition switch off 200 Ω or higher
H116-13 (CANL) - H19-4 (CG) Ignition switch off 200 Ω or higher
H116-2 (CANH) - H19-16 (BAT) Ignition switch off 6 kΩ or higher
H116-13 (CANL) - H19-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

26.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY)

NG

31.CONNECT CONNECTOR
26.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY)
a.
U153797E01
1.673,2.512 1.488,2.164 1.488,2.164 1.348,2.164 false 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 1.842,1.291 2.146,1.666 2.146,1.666 2.243,1.666 false 2.42,0.724 2.348,0.724 2.348,0.724 1.842,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.442,0.647 2.862,0.789 0.420,0.142 10 CANH 2.269,1.58 2.693,1.722 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.405,2.696 0.691,2.835 0.286,0.140 10 H19 0.452,1.122 0.803,1.261 0.351,0.140 10 H116 1.062,2.087 1.291,2.229 0.229,0.142 10 CG

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H116-5 (CANH) - H116-16 (CANL) Ignition switch off 200 Ω or higher
H116-5 (CANH) - H19-4 (CG) Ignition switch off 200 Ω or higher
H116-16 (CANL) - H19-4 (CG) Ignition switch off 200 Ω or higher
H116-5 (CANH) - H19-16 (BAT) Ignition switch off 6 kΩ or higher
H116-16 (CANL) - H19-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

27.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

NG

33.CONNECT CONNECTOR
27.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.
U153798E01
1.673,2.512 1.488,2.164 1.488,2.164 1.348,2.164 false 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 2.207,1.291 2.365,1.468 2.365,1.468 2.462,1.468 false 2.467,0.956 2.396,0.956 2.396,0.956 2.207,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.489,0.879 2.909,1.021 0.420,0.142 10 CANH 2.489,1.382 2.912,1.524 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.405,2.696 0.691,2.835 0.286,0.140 10 H19 0.452,1.122 0.803,1.261 0.351,0.140 10 H116 1.062,2.087 1.291,2.229 0.229,0.142 10 CG

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H116-1 (CANH) - H116-12 (CANL) Ignition switch off 108 to 132 Ω
H116-1 (CANH) - H19-4 (CG) Ignition switch off 200 Ω or higher
H116-12 (CANL) - H19-4 (CG) Ignition switch off 200 Ω or higher
H116-1 (CANH) - H19-16 (BAT) Ignition switch off 6 kΩ or higher
H116-12 (CANL) - H19-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3

Result
Result Proceed to
OK (w/ Power Back Door System) A
OK (w/o Power Back Door System) B
NG C



A

REPLACE NO. 3 JUNCTION CONNECTOR

B

28.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)

C

35.CONNECT CONNECTOR
28.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)
a.
U153794E01
1.673,2.512 1.488,2.164 1.488,2.164 1.348,2.164 false 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 1.932,1.291 2.305,1.597 2.305,1.597 2.402,1.597 false 2.381,0.746 2.31,0.746 2.31,0.746 1.932,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.403,0.668 2.823,0.810 0.420,0.142 10 CANH 2.428,1.511 2.852,1.653 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.405,2.696 0.691,2.835 0.286,0.140 10 H19 0.452,1.122 0.803,1.261 0.351,0.140 10 H116 1.062,2.087 1.291,2.229 0.229,0.142 10 CG

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H116-4 (CANH) - H116-15 (CANL) Ignition switch off 108 to 132 Ω
H116-4 (CANH) - H19-4 (CG) Ignition switch off 200 Ω or higher
H116-15 (CANL) - H19-4 (CG) Ignition switch off 200 Ω or higher
H116-4 (CANH) - H19-16 (BAT) Ignition switch off 6 kΩ or higher
H116-15 (CANL) - H19-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 3 JUNCTION CONNECTOR

NG

37.CONNECT CONNECTOR
29.CONNECT CONNECTOR
a.

Reconnect the H116 No. 3 junction connector.



NEXT

30.CHECK FOR SHORT IN CAN BUS WIRES (FRONT POWER SEAT SWITCH LH)
30.CHECK FOR SHORT IN CAN BUS WIRES (FRONT POWER SEAT SWITCH LH)
a.
U153888E01
1.673,2.512 1.488,2.164 1.488,2.164 1.348,2.164 false 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 1.497,1.47 1.33,1.609 1.33,1.609 1.233,1.609 false 1.264,1.125 1.336,1.125 1.336,1.125 1.497,1.265 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 0.717,1.526 1.137,1.668 0.420,0.142 10 CANH 0.787,1.039 1.180,1.181 0.393,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.405,2.696 0.691,2.835 0.286,0.140 10 H19 2.425,1.273 2.689,1.413 0.265,0.140 10 X11 1.062,2.087 1.291,2.229 0.229,0.142 10 CG

Disconnect the X11 front power seat switch LH (power seat control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
X11-5 (CANH) - X11-1 (CANL) Ignition switch off 54 to 69 Ω
X11-5 (CANH) - H19-4 (CG) Ignition switch off 200 Ω or higher
X11-1 (CANL) - H19-4 (CG) Ignition switch off 200 Ω or higher
X11-5 (CANH) - H19-16 (BAT) Ignition switch off 6 kΩ or higher
X11-1 (CANL) - H19-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Front Power Seat Switch LH [Power Seat Control ECU])
*b Front view of DLC3



OK

REPLACE FRONT POWER SEAT SWITCH LH (POWER SEAT CONTROL ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER SEAT CONTROL ECU (CANH, CANL)

31.CONNECT CONNECTOR
a.

Reconnect the H116 No. 3 junction connector.



NEXT

32.CHECK FOR SHORT IN CAN BUS WIRES (MULTIPLEX TILT AND TELESCOPIC ECU)
32.CHECK FOR SHORT IN CAN BUS WIRES (MULTIPLEX TILT AND TELESCOPIC ECU)
a.
U153889E01
1.673,2.512 1.488,2.164 1.488,2.164 1.348,2.164 false 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 1.368,1.732 1.491,1.732 1.491,1.732 1.741,1.36 false 2.206,0.553 2.083,0.553 2.083,0.553 1.727,1.083 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.228,0.476 2.648,0.618 0.420,0.142 10 CANH 0.889,1.653 1.278,1.795 0.389,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.405,2.696 0.691,2.835 0.286,0.140 10 H19 0.405,1.127 0.679,1.267 0.274,0.140 10 H57 1.062,2.087 1.291,2.229 0.229,0.142 10 CG

Disconnect the H57 multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H57-5 (CANH) - H57-14 (CANL) Ignition switch off 54 to 69 Ω
H57-5 (CANH) - H19-4 (CG) Ignition switch off 200 Ω or higher
H57-14 (CANL) - H19-4 (CG) Ignition switch off 200 Ω or higher
H57-5 (CANH) - H19-16 (BAT) Ignition switch off 6 kΩ or higher
H57-14 (CANL) - H19-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MULTIPLEX TILT AND TELESCOPIC ECU (CANH, CANL)

33.CONNECT CONNECTOR
a.

Reconnect the H116 No. 3 junction connector.



NEXT

34.CHECK FOR SHORT IN CAN BUS WIRES (OUTER MIRROR CONTROL ECU ASSEMBLY)
34.CHECK FOR SHORT IN CAN BUS WIRES (OUTER MIRROR CONTROL ECU ASSEMBLY)
a.
U153890E01
1.673,2.512 1.488,2.164 1.488,2.164 1.348,2.164 false 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 0.755,1.267 0.905,1.582 0.905,1.582 1.002,1.582 false 0.532,0.778 0.604,0.778 0.604,0.778 0.746,1.104 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 0.156,0.686 0.576,0.828 0.420,0.142 10 CAN 1.017,1.505 1.472,1.647 0.455,0.142 10 CGND 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.405,2.696 0.691,2.835 0.286,0.140 10 H19 1.585,0.367 1.801,0.507 0.216,0.140 10 M8 1.062,2.087 1.291,2.229 0.229,0.142 10 CG

Disconnect the M8 outer mirror control ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
M8-1 (CAN) - M8-21 (CGND) Ignition switch off 54 to 69 Ω
M8-1 (CAN) - H19-4 (CG) Ignition switch off 200 Ω or higher
M8-21 (CGND) - H19-4 (CG) Ignition switch off 200 Ω or higher
M8-1 (CAN) - H19-16 (BAT) Ignition switch off 6 kΩ or higher
M8-21 (CGND) - H19-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly)
*b Front view of DLC3



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO OUTER MIRROR CONTROL ECU ASSEMBLY (CAN, CGND)

35.CONNECT CONNECTOR
a.

Reconnect the H116 No. 3 junction connector.



NEXT

36.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)
36.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)
a.
U153845E01
1.673,2.512 1.488,2.164 1.488,2.164 1.348,2.164 false 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 2.475,1.064 2.607,1.252 2.607,1.252 2.704,1.252 false 2.624,0.865 2.553,0.865 2.553,0.865 2.392,1.006 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.646,0.788 3.066,0.930 0.420,0.142 10 CANH 2.731,1.166 3.154,1.308 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.405,2.696 0.691,2.835 0.286,0.140 10 H19 0.445,0.887 0.719,1.026 0.274,0.140 10 H37 1.062,2.087 1.291,2.229 0.229,0.142 10 CG

Disconnect the H37 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H37-22 (CANH) - H37-21 (CANL) Ignition switch off 108 to 132 Ω
H37-22 (CANH) - H19-4 (CG) Ignition switch off 200 Ω or higher
H37-21 (CANL) - H19-4 (CG) Ignition switch off 200 Ω or higher
H37-22 (CANH) - H19-16 (BAT) Ignition switch off 6 kΩ or higher
H37-21 (CANL) - H19-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Combination Meter Assembly)
*b Front view of DLC3



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)

37.CONNECT CONNECTOR
a.

Reconnect the H116 No. 3 junction connector.



NEXT

38.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
38.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
a.
U153866E01
1.673,2.512 1.488,2.164 1.488,2.164 1.348,2.164 false 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 2.005,1.457 2.172,1.596 2.172,1.596 2.269,1.596 false 2.236,1.11 2.164,1.11 2.164,1.11 1.89,1.364 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.258,1.033 2.678,1.175 0.420,0.142 10 CANN 2.295,1.51 2.719,1.652 0.424,0.142 10 CANP 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.405,2.696 0.691,2.835 0.286,0.140 10 H19 1.062,2.087 1.291,2.229 0.229,0.142 10 CG 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.668,1.129 0.863,1.268 0.195,0.140 10 H2

Disconnect the H2 main body ECU (cowl side junction block LH) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H2-16 (CANP) - H2-15 (CANN) Ignition switch off 108 to 132 Ω
H2-16 (CANP) - H19-4 (CG) Ignition switch off 200 Ω or higher
H2-15 (CANN) - H19-4 (CG) Ignition switch off 200 Ω or higher
H2-16 (CANP) - H19-16 (BAT) Ignition switch off 6 kΩ or higher
H2-15 (CANN) - H19-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Main Body ECU [Cowl Side Junction Block LH])
*b Front view of DLC3



OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)

39.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
a.

Connect the cable to the negative (-) battery terminal.

U153978E01
0.227,0.14 0.464,0.363 0.237,0.223 10 *a 1.043,0.796 1.255,0.940 0.211,0.144 10 DA 0.268,2.441 0.726,2.594 0.458,0.152 10 ALTB 2.899,2.231 3.336,2.390 0.437,0.159 10 BECU 5.527,2.306 5.947,2.469 0.420,0.163 10 GND1 1.038,2.043 0.753,2.505 0.753,2.505 0.62,2.505 false 3.189,1.064 3.401,1.208 0.211,0.144 10 DB 5.632,1.064 5.850,1.208 0.218,0.144 10 DD 2.467,1.828 2.752,2.291 2.752,2.291 2.885,2.291 false 5.243,1.693 5.381,2.37 5.381,2.37 5.514,2.37 false

Text in Illustration
*a Front view of wire harness connector
(to Main Body ECU [Cowl Side Junction Block LH])
- -

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the DA, DB and DD main body ECU (cowl side junction block LH) connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DD-62 (GND1) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
DA-1 (ALTB) - Body ground Always 11 to 14 V
DB-13 (BECU) - Body ground Always 11 to 14 V




OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR