Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM27L0U _57 Power Source / Network _049335 NETWORKING _0235802 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U1002 (CAN No. 2 BUS)  Lost Communication with Gateway Module (Network Gateway ECU)  


DESCRIPTION

·

The network gateway ECU stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the CAN V2 bus.

·

When the network gateway ECU receives a response signal from the ECUs connected to the CAN V2 bus, the network gateway ECU recognizes and memorizes that the ECU is connected to the CAN V2 bus. Based on this memorized data, the network gateway ECU monitors for malfunctions in the ECUs connected to the CAN V2 bus when communicating with those ECUs. If the network gateway ECU cannot receive response signals from the ECUs that have been memorized as those connected to the CAN V2 bus, the network gateway ECU determines that a malfunction exists.

·

If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).


DTC Code DTC Detection Condition Trouble Area
U1002 Lost communication with the gateway module.
·

V2 bus circuit

·

Network gateway ECU CAN main wire or connector

·

Distance control ECU assembly CAN branch wire or connector*1

·

Blind spot monitor sensor LH CAN branch wire or connector*2

·

Blind spot monitor sensor RH CAN branch wire or connector*2

·

Network gateway ECU

·

Distance control ECU assembly*1

·

Blind spot monitor sensor LH*2

·

Blind spot monitor sensor RH*2

·

No. 3 junction connector

·

No. 5 junction connector

·

No. 6 junction connector

·

No. 7 junction connector



*1: w/ Dynamic Laser Cruise Control System

*2: w/ Blind Spot Monitor Sensor

For vehicles with an network gateway ECU.


WIRING DIAGRAM

C242746E01
5.374,1.245 5.748,1.382 0.374,0.137 10 H120 5.374,1.407 6.823,1.543 1.449,0.137 10 Network Gateway ECU 5.595,0.993 6.058,1.130 0.463,0.137 10 CA2L 5.595,0.422 6.058,0.559 0.463,0.137 10 CA2H 0.815,1.359 2.201,1.665 1.385,0.305 10 Distance Control ECU Assembly*1 0.815,1.224 1.088,1.361 0.272,0.137 10 A43 5.336,0.815 5.507,0.951 0.172,0.137 10 12 5.336,0.436 5.507,0.573 0.172,0.137 10 13 1.903,0.815 2.075,0.951 0.172,0.137 10 9 1.903,0.436 2.075,0.573 0.172,0.137 10 8 3.991,0.815 4.162,0.951 0.172,0.137 10 21 3.991,0.436 4.173,0.573 0.182,0.137 10 10 3.097,0.815 3.269,0.951 0.172,0.137 10 22 3.097,0.436 3.269,0.573 0.172,0.137 10 11 1.377,0.904 1.771,1.041 0.394,0.137 10 CANL 1.356,0.521 1.770,0.658 0.415,0.137 10 CANH 3.991,1.938 4.162,2.075 0.172,0.137 10 20 3.991,1.56 4.086,1.696 0.095,0.137 10 9 5.41,5.941 5.508,6.078 0.097,0.137 10 4 5.406,5.563 5.508,5.700 0.102,0.137 10 8 5.595,6.03 5.989,6.167 0.394,0.137 10 CA1N 5.595,5.648 6.009,5.784 0.415,0.137 10 CA1P 5.41,7.785 5.508,7.922 0.097,0.137 10 2 5.406,7.405 5.508,7.542 0.102,0.137 10 3 5.595,7.966 5.989,8.102 0.394,0.137 10 CANL 5.595,7.403 6.009,7.540 0.415,0.137 10 CANH 0.844,3.754 1.241,3.891 0.397,0.137 10 O46 0.844,3.903 2.204,4.215 1.361,0.312 10 Blind Spot Monitor Sensor LH*2 1.903,3.325 2.075,3.462 0.172,0.137 10 4 1.903,2.946 2.075,3.083 0.172,0.137 10 8 3.097,3.325 3.269,3.462 0.172,0.137 10 22 3.097,2.946 3.269,3.083 0.172,0.137 10 11 3.097,4.596 3.269,4.733 0.172,0.137 10 21 3.097,4.218 3.269,4.355 0.172,0.137 10 10 3.991,3.325 4.162,3.462 0.172,0.137 10 20 3.991,2.946 4.086,3.083 0.095,0.137 10 9 3.977,5.94 4.148,6.077 0.172,0.137 10 21 3.977,5.562 4.148,5.699 0.172,0.137 10 10 3.977,7.788 4.148,7.925 0.172,0.137 10 22 3.977,7.41 4.148,7.547 0.172,0.137 10 11 3.097,5.94 3.269,6.077 0.172,0.137 10 20 3.174,5.562 3.270,5.699 0.095,0.137 10 9 1.377,3.414 1.771,3.551 0.394,0.137 10 CA1N 1.38,3.031 1.771,3.168 0.390,0.137 10 CA1P 2.889,2.516 4.479,2.662 1.590,0.145 10 No. 3 Junction Connector 2.889,2.381 3.279,2.518 0.390,0.137 10 H116 2.889,5.113 4.479,5.258 1.590,0.145 10 No. 5 Junction Connector 2.889,4.95 3.279,5.087 0.390,0.137 10 O47 2.889,8.384 4.479,8.530 1.590,0.145 10 No. 6 Junction Connector 2.889,8.221 3.279,8.358 0.390,0.137 10 O48 5.334,8.384 6.924,8.530 1.590,0.145 10 No. 7 Junction Connector 5.334,8.221 5.724,8.358 0.390,0.137 10 O49 0.178,7.678 2.948,7.820 2.770,0.142 10 *1: w/ Dynamic Laser Cruise Control System 0.178,7.952 2.948,8.093 2.770,0.142 10 *2: w/ Blind Spot Monitor Sensor 5.383,6.363 5.780,6.499 0.397,0.137 10 P25 5.383,6.512 6.744,6.824 1.361,0.312 10 Blind Spot Monitor Sensor RH*2

CAUTION / NOTICE / HINT

HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK CAN BUS WIRE (CHECK MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT)
3.CHECK CAN BUS WIRE (CHECK MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT)
a.
U153747E01
1.386,0.948 1.116,0.586 1.116,0.586 1.017,0.586 false 2.062,0.948 2.332,0.586 2.332,0.586 2.431,0.586 false 1.659,1.08 1.923,1.592 1.923,1.592 2.003,1.592 false 1.562,1.08 1.298,1.592 1.298,1.592 1.219,1.592 false 2.022,1.51 2.388,1.651 0.366,0.140 10 CA2L 0.733,1.51 1.124,1.651 0.390,0.140 10 CA2H 0.62,0.505 1.010,0.645 0.390,0.140 10 GND 2.452,0.505 2.842,0.645 0.390,0.140 10 BATT 0.063,0.042 0.369,0.182 0.306,0.140 10 *a 1.49,0.39 1.847,0.527 0.357,0.137 10 H120

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition Resistance: Malfunction
H120-13 (CA2H) - H120-12 (CA2L) Ignition switch off 54 to 69 Ω Below 53 Ω: Short in line
H120-13 (CA2H) - H120-12 (CA2L) Ignition switch off 54 to 69 Ω Higher than 70 Ω: Open in CAN main bus line
H120-13 (CA2H) - H120-2 (BATT) Ignition switch off 6 kΩ or higher Below 6 kΩ: +B short
H120-12 (CA2L) - H120-2 (BATT) Ignition switch off 6 kΩ or higher Below 6 kΩ: +B short
H120-13 (CA2H) - H120-4 (GND) Ignition switch off 200 Ω or higher Below 200 Ω: Ground short
H120-12 (CA2L) - H120-4 (GND) Ignition switch off 200 Ω or higher Below 200 Ω: Ground short


Text in Illustration
*a Component with harness connected
(Network Gateway ECU)

Result
Result Proceed to
NG
·

Open in CAN main bus line


A
NG
·

Short in line

·

+B short

·

GND short


B
OK C



A

4.CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

B

16.CHECK FOR SHORT IN CAN BUS WIRE (NO. 6 JUNCTION CONNECTOR SIDE)

C

37.CHECK HARNESS AND CONNECTOR (NETWORK GATEWAY ECU - BATTERY AND BODY GROUND)
4.CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)
a.
U153748E01
0.963,0.873 1.047,0.873 1.047,0.873 1.393,1.234 false 1.393,1.439 1.131,1.771 1.131,1.771 1.06,1.771 false 0.447,0.795 0.867,0.932 0.421,0.137 10 CANH 0.571,1.689 0.967,1.826 0.396,0.137 10 CANL 0.062,0.058 0.458,0.195 0.396,0.137 10 *a 2.591,1.23 2.871,1.367 0.280,0.137 10 O47

Disconnect the O47 No. 5 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
O47-9 (CANH) - O47-20 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 5 Junction Connector)



OK

5.CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)

NG

6.CONNECT CONNECTOR
5.CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)
a.
U153749E01
0.976,1.01 1.06,1.01 1.06,1.01 1.294,1.234 false 1.294,1.439 1.098,1.704 1.098,1.704 1.028,1.704 false 0.459,0.933 0.880,1.070 0.421,0.137 10 CANH 0.539,1.622 0.935,1.759 0.396,0.137 10 CANL 0.062,0.058 0.458,0.195 0.396,0.137 10 *a 2.625,1.269 2.905,1.406 0.280,0.137 10 O47

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
O47-10 (CANH) - O47-21 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 5 Junction Connector)



OK

REPLACE NO. 5 JUNCTION CONNECTOR

NG

11.CONNECT CONNECTOR
6.CONNECT CONNECTOR
a.

Reconnect the O47 No. 5 junction connector.



NEXT

7.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)
7.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)
a.
U153759E01
0.967,1.032 1.051,1.032 1.051,1.032 1.303,1.234 false 1.303,1.439 1.081,1.73 1.081,1.73 1.01,1.73 false 0.451,0.954 0.871,1.091 0.421,0.137 10 CANH 0.522,1.648 0.918,1.785 0.396,0.137 10 CANL 0.062,0.058 0.458,0.195 0.396,0.137 10 *a 2.6,1.257 2.949,1.394 0.349,0.137 10 H116

Disconnect the H116 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H116-10 (CANH) - H116-21 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

8.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)

NG

9.CONNECT CONNECTOR
8.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
a.
U153760E01
0.963,0.873 1.047,0.873 1.047,0.873 1.393,1.234 false 1.393,1.439 1.131,1.771 1.131,1.771 1.06,1.771 false 0.447,0.795 0.867,0.932 0.421,0.137 10 CANH 0.571,1.689 0.967,1.826 0.396,0.137 10 CANL 0.062,0.058 0.458,0.195 0.396,0.137 10 *a 2.602,1.245 2.953,1.382 0.351,0.137 10 H116

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H116-9 (CANH) - H116-20 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

REPLACE NO. 3 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)

9.CONNECT CONNECTOR
a.

Reconnect the H116 No. 3 junction connector.



NEXT

10.CHECK FOR OPEN IN CAN BUS WIRE (NETWORK GATEWAY ECU)
10.CHECK FOR OPEN IN CAN BUS WIRE (NETWORK GATEWAY ECU)
a.
U153770E01
0.501,1.136 0.858,1.273 0.357,0.137 10 H120 1.59,1.295 1.332,1.717 1.332,1.717 1.209,1.717 false 1.412,1.935 1.484,1.935 1.484,1.935 1.699,1.293 false 0.719,1.643 1.108,1.780 0.389,0.137 10 CA2H 0.962,1.849 1.351,1.986 0.389,0.137 10 CA2L 0.07,0.056 0.371,0.193 0.301,0.137 10 *a

Disconnect the H120 network gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H120-13 (CA2H) - H120-12 (CA2L) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Network Gateway ECU)



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO NETWORK GATEWAY ECU (NETWORK GATEWAY ECU - NO. 3 JUNCTION CONNECTOR)

11.CONNECT CONNECTOR
a.

Reconnect the O47 No. 5 junction connector.



NEXT

12.CHECK FOR OPEN IN CAN BUS WIRE (NO. 6 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)
12.CHECK FOR OPEN IN CAN BUS WIRE (NO. 6 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)
a.
U153750E01
0.946,1.045 1.03,1.045 1.03,1.045 1.204,1.234 false 1.204,1.439 1.066,1.698 1.066,1.698 0.995,1.698 false 0.429,0.967 0.850,1.104 0.421,0.137 10 CANH 0.507,1.616 0.903,1.753 0.396,0.137 10 CANL 0.062,0.058 0.458,0.195 0.396,0.137 10 *a 2.624,1.262 2.904,1.399 0.280,0.137 10 O48

Disconnect the O48 No. 6 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
O48-11 (CANH) - O48-22 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 6 Junction Connector)



OK

13.CHECK FOR OPEN IN CAN BUS WIRE (NO. 6 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)

NG

14.CONNECT CONNECTOR
13.CHECK FOR OPEN IN CAN BUS WIRE (NO. 6 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
a.
U153751E01
2.624,1.262 2.904,1.399 0.280,0.137 10 O48 0.963,0.873 1.047,0.873 1.047,0.873 1.393,1.234 false 1.393,1.439 1.131,1.771 1.131,1.771 1.06,1.771 false 0.447,0.795 0.867,0.932 0.421,0.137 10 CANH 0.571,1.689 0.967,1.826 0.396,0.137 10 CANL 0.062,0.058 0.458,0.195 0.396,0.137 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
O48-9 (CANH) - O48-20 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 6 Junction Connector)



OK

REPLACE NO. 6 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)

14.CONNECT CONNECTOR
a.

Reconnect the O48 No. 6 junction connector.



NEXT

15.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 JUNCTION CONNECTOR)
15.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 JUNCTION CONNECTOR)
a.
U153743E01
1.331,0.998 0.975,1.513 0.975,1.513 0.851,1.513 false 1.195,1.857 1.323,1.857 1.323,1.857 1.676,0.998 false 0.318,1.434 0.873,1.574 0.555,0.139 10 CANH 0.667,1.783 1.222,1.922 0.555,0.139 10 CANL 0.066,0.057 0.621,0.196 0.555,0.139 10 *a 2.645,0.81 2.925,0.948 0.280,0.137 10 O49

Disconnect the O49 No. 7 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
O49-3 (CANH) - O49-2 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 7 Junction Connector)



OK

REPLACE NO. 7 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 7 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)

16.CHECK FOR SHORT IN CAN BUS WIRE (NO. 6 JUNCTION CONNECTOR SIDE)
a.
U153747E01
1.386,0.948 1.116,0.586 1.116,0.586 1.017,0.586 false 2.062,0.948 2.332,0.586 2.332,0.586 2.431,0.586 false 1.659,1.08 1.923,1.592 1.923,1.592 2.003,1.592 false 1.562,1.08 1.298,1.592 1.298,1.592 1.219,1.592 false 2.022,1.51 2.388,1.651 0.366,0.140 10 CA2L 0.733,1.51 1.124,1.651 0.390,0.140 10 CA2H 0.62,0.505 1.010,0.645 0.390,0.140 10 GND 2.452,0.505 2.842,0.645 0.390,0.140 10 BATT 0.063,0.042 0.369,0.182 0.306,0.140 10 *a 1.49,0.39 1.847,0.527 0.357,0.137 10 H120

Disconnect the O48 No. 6 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H120-13 (CA2H) - H120-12 (CA2L) Ignition switch off 108 to 132 Ω
H120-13 (CA2H) - H120-4 (GND) Ignition switch off 200 Ω or higher
H120-12 (CA2L) - H120-4 (GND) Ignition switch off 200 Ω or higher
H120-13 (CA2H) - H120-2 (BATT) Ignition switch off 6 kΩ or higher
H120-12 (CA2L) - H120-2 (BATT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Component with harness connected
(Network Gateway ECU)



OK

17.CHECK FOR SHORT IN CAN BUS WIRE (NO. 6 JUNCTION CONNECTOR - BLIND SPOT MONITOR SENSOR RH)

NG

23.CONNECT CONNECTOR
17.CHECK FOR SHORT IN CAN BUS WIRE (NO. 6 JUNCTION CONNECTOR - BLIND SPOT MONITOR SENSOR RH)
NOTICE:

For vehicles without an blind spot monitor sensor, go to "Check for Short in CAN Bus Wire (No. 6 Junction Connector - No. 7 Junction Connector)".


a.
U153774E01
2.535,1.12 2.816,1.258 0.280,0.137 10 O48 1.334,2.154 1.426,2.154 1.426,2.154 1.665,2.524 false 2.219,2.959 2.357,3.208 2.357,3.208 2.497,3.208 false 1.338,1.274 1.154,1.518 1.154,1.518 1.056,1.518 false 1.061,0.961 1.132,0.961 1.132,0.961 1.338,1.117 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 0.554,0.884 1.209,1.026 0.656,0.142 10 CANH 0.544,1.432 0.967,1.574 0.424,0.142 10 CANL 1.045,2.078 1.469,2.220 0.424,0.142 10 CG 2.532,3.14 2.955,3.282 0.424,0.142 10 BAT 0.394,2.696 0.680,2.835 0.286,0.140 10 H19

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
O48-10 (CANH) - O48-21 (CANL) Ignition switch off 200 Ω or higher
O48-10 (CANH) - H19-4 (CG) Ignition switch off 200 Ω or higher
O48-21 (CANL) - H19-4 (CG) Ignition switch off 200 Ω or higher
O48-10 (CANH) - H19-16 (BAT) Ignition switch off 6 kΩ or higher
O48-21 (CANL) - H19-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 6 Junction Connector)
*b Front view of DLC3



OK

18.CHECK FOR SHORT IN CAN BUS WIRE (NO. 6 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)

NG

19.CONNECT CONNECTOR
18.CHECK FOR SHORT IN CAN BUS WIRE (NO. 6 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)
a.
U153773E01
1.334,2.154 1.426,2.154 1.426,2.154 1.665,2.524 false 2.219,2.959 2.357,3.208 2.357,3.208 2.497,3.208 false 1.255,1.274 1.152,1.473 1.152,1.473 1.055,1.473 false 1.043,0.977 1.115,0.977 1.115,0.977 1.255,1.109 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 0.536,0.9 1.192,1.042 0.656,0.142 10 CANH 0.542,1.387 0.966,1.529 0.424,0.142 10 CANL 1.045,2.078 1.469,2.220 0.424,0.142 10 CG 2.532,3.14 2.955,3.282 0.424,0.142 10 BAT 0.394,2.696 0.680,2.835 0.286,0.140 10 H19 2.535,1.12 2.816,1.258 0.280,0.137 10 O48

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
O48-11 (CANH) - O48-22 (CANL) Ignition switch off 108 to 132 Ω
O48-11 (CANH) - H19-4 (CG) Ignition switch off 200 Ω or higher
O48-22 (CANL) - H19-4 (CG) Ignition switch off 200 Ω or higher
O48-11 (CANH) - H19-16 (BAT) Ignition switch off 6 kΩ or higher
O48-22 (CANL) - H19-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 6 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 6 JUNCTION CONNECTOR

NG

21.CONNECT CONNECTOR
19.CONNECT CONNECTOR
a.

Reconnect the O48 No. 6 junction connector.



NEXT

20.CHECK FOR SHORT IN CAN BUS WIRE (BLIND SPOT MONITOR SENSOR RH)
20.CHECK FOR SHORT IN CAN BUS WIRE (BLIND SPOT MONITOR SENSOR RH)
a.
U153813E01
1.334,2.154 1.426,2.154 1.426,2.154 1.665,2.524 false 2.219,2.959 2.357,3.208 2.357,3.208 2.497,3.208 false 1.984,1.274 2.194,1.53 2.194,1.53 2.291,1.53 false 2.303,0.865 2.231,0.865 2.231,0.865 1.984,1.117 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.322,0.788 2.978,0.930 0.656,0.142 10 CA1N 2.322,1.444 2.746,1.586 0.424,0.142 10 CA1P 1.045,2.078 1.469,2.220 0.424,0.142 10 CG 2.532,3.14 2.955,3.282 0.424,0.142 10 BAT 0.394,2.696 0.680,2.835 0.286,0.140 10 H19 0.592,1.132 0.858,1.269 0.266,0.137 10 P25

Disconnect the P25 blind spot monitor sensor RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
P25-8 (CA1P) - P25-4 (CA1N) Ignition switch off 54 to 69 Ω
P25-8 (CA1P) - H19-4 (CG) Ignition switch off 200 Ω or higher
P25-4 (CA1N) - H19-4 (CG) Ignition switch off 200 Ω or higher
P25-8 (CA1P) - H19-16 (BAT) Ignition switch off 6 kΩ or higher
P25-4 (CA1N) - H19-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BLIND SPOT MONITOR SENSOR RH (CA1P, CA1N)

21.CONNECT CONNECTOR
a.

Reconnect the O48 No. 6 junction connector.



NEXT

22.CHECK FOR SHORT IN CAN BUS WIRE (NO. 7 JUNCTION CONNECTOR)
22.CHECK FOR SHORT IN CAN BUS WIRE (NO. 7 JUNCTION CONNECTOR)
a.
U153815E01
1.334,2.154 1.426,2.154 1.426,2.154 1.665,2.524 false 2.219,2.959 2.357,3.208 2.357,3.208 2.497,3.208 false 1.377,0.891 1.138,1.276 1.138,1.276 1.04,1.276 false 1.338,0.314 1.41,0.314 1.41,0.314 1.691,0.708 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 0.883,0.228 1.272,0.370 0.389,0.142 10 CANL 0.522,1.199 0.946,1.341 0.424,0.142 10 CANH 1.045,2.078 1.469,2.220 0.424,0.142 10 CG 2.532,3.14 2.955,3.282 0.424,0.142 10 BAT 0.394,2.696 0.680,2.835 0.286,0.140 10 H19 2.598,0.823 2.879,0.960 0.280,0.137 10 O49

Disconnect the O49 No. 7 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
O49-3 (CANH) - O49-2 (CANL) Ignition switch off 108 to 132 Ω
O49-3 (CANH) - H19-4 (CG) Ignition switch off 200 Ω or higher
O49-2 (CANL) - H19-4 (CG) Ignition switch off 200 Ω or higher
O49-3 (CANH) - H19-16 (BAT) Ignition switch off 6 kΩ or higher
O49-2 (CANL) - H19-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 7 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 7 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 7 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)

23.CONNECT CONNECTOR
a.

Reconnect the O48 No. 6 junction connector.



NEXT

24.CHECK FOR SHORT IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)
24.CHECK FOR SHORT IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)
a.
U153775E01
1.334,2.154 1.426,2.154 1.426,2.154 1.665,2.524 false 2.219,2.959 2.357,3.208 2.357,3.208 2.497,3.208 false 1.34,1.274 1.167,1.541 1.167,1.541 1.07,1.541 false 1.048,0.833 1.119,0.833 1.119,0.833 1.34,1.117 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 0.541,0.756 1.197,0.898 0.656,0.142 10 CANH 0.557,1.455 0.981,1.597 0.424,0.142 10 CANL 1.045,2.078 1.469,2.220 0.424,0.142 10 CG 2.532,3.14 2.955,3.282 0.424,0.142 10 BAT 0.394,2.696 0.680,2.835 0.286,0.140 10 H19 2.555,1.126 2.836,1.263 0.280,0.137 10 O47

Disconnect the O47 No. 5 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
O47-10 (CANH) - O47-21 (CANL) Ignition switch off 108 to 132 Ω
O47-10 (CANH) - H19-4 (CG) Ignition switch off 200 Ω or higher
O47-21 (CANL) - H19-4 (CG) Ignition switch off 200 Ω or higher
O47-10 (CANH) - H19-16 (BAT) Ignition switch off 6 kΩ or higher
O47-21 (CANL) - H19-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 5 Junction Connector)
*b Front view of DLC3



OK

25.CHECK FOR SHORT IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR SIDE)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)

25.CHECK FOR SHORT IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR SIDE)
a.
U153747E01
1.386,0.948 1.116,0.586 1.116,0.586 1.017,0.586 false 2.062,0.948 2.332,0.586 2.332,0.586 2.431,0.586 false 1.659,1.08 1.923,1.592 1.923,1.592 2.003,1.592 false 1.562,1.08 1.298,1.592 1.298,1.592 1.219,1.592 false 2.022,1.51 2.388,1.651 0.366,0.140 10 CA2L 0.733,1.51 1.124,1.651 0.390,0.140 10 CA2H 0.62,0.505 1.010,0.645 0.390,0.140 10 GND 2.452,0.505 2.842,0.645 0.390,0.140 10 BATT 0.063,0.042 0.369,0.182 0.306,0.140 10 *a 1.49,0.39 1.847,0.527 0.357,0.137 10 H120

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H120-13 (CA2H) - H120-12 (CA2L) Ignition switch off 108 to 132 Ω
H120-13 (CA2H) - H120-4 (GND) Ignition switch off 200 Ω or higher
H120-12 (CA2L) - H120-4 (GND) Ignition switch off 200 Ω or higher
H120-13 (CA2H) - H120-2 (BATT) Ignition switch off 6 kΩ or higher
H120-12 (CA2L) - H120-2 (BATT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Component with harness connected
(Network Gateway ECU)

Result
Result Proceed to
OK (w/ Blind Spot Monitor Sensor) A
OK (w/o Blind Spot Monitor Sensor) B
NG C



A

26.CHECK FOR SHORT IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR - BLIND SPOT MONITOR SENSOR LH)

B

REPLACE NO. 5 JUNCTION CONNECTOR

C

29.CONNECT CONNECTOR
26.CHECK FOR SHORT IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR - BLIND SPOT MONITOR SENSOR LH)
a.
U153776E01
2.532,1.1 2.840,1.251 0.308,0.151 11 O47 1.334,2.154 1.426,2.154 1.426,2.154 1.665,2.524 false 2.219,2.959 2.357,3.208 2.357,3.208 2.497,3.208 false 1.246,1.274 1.168,1.49 1.168,1.49 1.071,1.49 false 1.025,0.963 1.096,0.963 1.096,0.963 1.246,1.117 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 0.518,0.885 1.174,1.027 0.656,0.142 10 CANH 0.558,1.404 0.982,1.546 0.424,0.142 10 CANL 1.045,2.078 1.469,2.220 0.424,0.142 10 CG 2.532,3.14 2.955,3.282 0.424,0.142 10 BAT 0.394,2.696 0.680,2.835 0.286,0.140 10 H19

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
O47-11 (CANH) - O47-22 (CANL) Ignition switch off 108 to 132 Ω
O47-11 (CANH) - H19-4 (CG) Ignition switch off 200 Ω or higher
O47-22 (CANL) - H19-4 (CG) Ignition switch off 200 Ω or higher
O47-11 (CANH) - H19-16 (BAT) Ignition switch off 6 kΩ or higher
O47-22 (CANL) - H19-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 5 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 5 JUNCTION CONNECTOR

NG

27.CONNECT CONNECTOR
27.CONNECT CONNECTOR
a.

Reconnect the O47 No. 5 junction connector.



NEXT

28.CHECK FOR SHORT IN CAN BUS WIRE (BLIND SPOT MONITOR SENSOR LH)
28.CHECK FOR SHORT IN CAN BUS WIRE (BLIND SPOT MONITOR SENSOR LH)
a.
U153814E01
1.334,2.154 1.426,2.154 1.426,2.154 1.665,2.524 false 2.219,2.959 2.357,3.208 2.357,3.208 2.497,3.208 false 1.984,1.274 2.194,1.53 2.194,1.53 2.291,1.53 false 2.303,0.865 2.231,0.865 2.231,0.865 1.984,1.117 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.322,0.788 2.978,0.930 0.656,0.142 10 CA1N 2.322,1.444 2.746,1.586 0.424,0.142 10 CA1P 1.045,2.078 1.469,2.220 0.424,0.142 10 CG 2.532,3.14 2.955,3.282 0.424,0.142 10 BAT 0.394,2.696 0.680,2.835 0.286,0.140 10 H19 0.563,1.13 0.845,1.268 0.282,0.137 10 O46

Disconnect the O46 blind spot monitor sensor LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
O46-8 (CA1P) - O46-4 (CA1N) Ignition switch off 54 to 69 Ω
O46-8 (CA1P) - H19-4 (CG) Ignition switch off 200 Ω or higher
O46-4 (CA1N) - H19-4 (CG) Ignition switch off 200 Ω or higher
O46-8 (CA1P) - H19-16 (BAT) Ignition switch off 6 kΩ or higher
O46-4 (CA1N) - H19-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BLIND SPOT MONITOR SENSOR LH (CA1P, CA1N)

29.CONNECT CONNECTOR
a.

Reconnect the O47 No. 5 junction connector.



NEXT

30.CHECK FOR SHORT IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
30.CHECK FOR SHORT IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
a.
U153799E01
1.334,2.154 1.426,2.154 1.426,2.154 1.665,2.524 false 2.219,2.959 2.357,3.208 2.357,3.208 2.497,3.208 false 1.431,1.274 1.284,1.597 1.284,1.597 1.187,1.597 false 1.016,0.838 1.088,0.838 1.088,0.838 1.431,1.117 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 0.509,0.761 1.165,0.903 0.656,0.142 10 CANH 0.674,1.511 1.098,1.653 0.424,0.142 10 CANL 1.045,2.078 1.469,2.220 0.424,0.142 10 CG 2.532,3.14 2.955,3.282 0.424,0.142 10 BAT 0.394,2.696 0.680,2.835 0.286,0.140 10 H19 2.538,1.106 2.890,1.246 0.351,0.140 10 H116

Disconnect the H116 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H116-9 (CANH) - H116-20 (CANL) Ignition switch off 108 to 132 Ω
H116-9 (CANH) - H19-4 (CG) Ignition switch off 200 Ω or higher
H116-20 (CANL) - H19-4 (CG) Ignition switch off 200 Ω or higher
H116-9 (CANH) - H19-16 (BAT) Ignition switch off 6 kΩ or higher
H116-20 (CANL) - H19-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

31.CHECK FOR SHORT IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - DISTANCE CONTROL ECU ASSEMBLY)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)

31.CHECK FOR SHORT IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - DISTANCE CONTROL ECU ASSEMBLY)
NOTICE:

For vehicles without an dynamic laser cruise control system, go to "Check for Short in CAN Bus Wire (No. 3 Junction Connector - Network Gateway ECU)".


a.
U153800E01
1.334,2.154 1.426,2.154 1.426,2.154 1.665,2.524 false 2.219,2.959 2.357,3.208 2.357,3.208 2.497,3.208 false 1.246,1.274 1.168,1.49 1.168,1.49 1.071,1.49 false 1.025,0.963 1.096,0.963 1.096,0.963 1.246,1.117 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 0.518,0.885 1.174,1.027 0.656,0.142 10 CANH 0.558,1.404 0.982,1.546 0.424,0.142 10 CANL 1.045,2.078 1.469,2.220 0.424,0.142 10 CG 2.532,3.14 2.955,3.282 0.424,0.142 10 BAT 0.394,2.696 0.680,2.835 0.286,0.140 10 H19 2.541,1.112 2.893,1.252 0.353,0.140 10 H116

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H116-11 (CANH) - H116-22 (CANL) Ignition switch off 200 Ω or higher
H116-11 (CANH) - H19-4 (CG) Ignition switch off 200 Ω or higher
H116-22 (CANL) - H19-4 (CG) Ignition switch off 200 Ω or higher
H116-11 (CANH) - H19-16 (BAT) Ignition switch off 6 kΩ or higher
H116-22 (CANL) - H19-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

32.CHECK FOR SHORT IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

NG

33.CONNECT CONNECTOR
32.CHECK FOR SHORT IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)
a.
U153801E01
1.334,2.154 1.426,2.154 1.426,2.154 1.665,2.524 false 2.219,2.959 2.357,3.208 2.357,3.208 2.497,3.208 false 1.338,1.274 1.205,1.544 1.205,1.544 1.108,1.544 false 1.026,0.872 1.098,0.872 1.098,0.872 1.338,1.117 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 0.519,0.795 0.939,0.937 0.420,0.142 10 CANH 0.595,1.458 1.019,1.600 0.424,0.142 10 CANL 1.045,2.078 1.469,2.220 0.424,0.142 10 CG 2.532,3.14 2.955,3.282 0.424,0.142 10 BAT 0.394,2.696 0.680,2.835 0.286,0.140 10 H19 2.543,1.122 2.893,1.262 0.350,0.140 10 H116

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H116-10 (CANH) - H116-21 (CANL) Ignition switch off 108 to 132 Ω
H116-10 (CANH) - H19-4 (CG) Ignition switch off 200 Ω or higher
H116-21 (CANL) - H19-4 (CG) Ignition switch off 200 Ω or higher
H116-10 (CANH) - H19-16 (BAT) Ignition switch off 6 kΩ or higher
H116-21 (CANL) - H19-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 3 JUNCTION CONNECTOR

NG

35.CONNECT CONNECTOR
33.CONNECT CONNECTOR
a.

Reconnect the H116 No. 3 junction connector.



NEXT

34.CHECK FOR SHORT IN CAN BUS WIRE (DISTANCE CONTROL ECU ASSEMBLY)
34.CHECK FOR SHORT IN CAN BUS WIRE (DISTANCE CONTROL ECU ASSEMBLY)
a.
U153816E01
1.334,2.154 1.426,2.154 1.426,2.154 1.665,2.524 false 2.219,2.959 2.357,3.208 2.357,3.208 2.497,3.208 false 1.576,1.095 1.203,1.529 1.203,1.529 1.105,1.529 false 0.953,0.568 1.024,0.568 1.024,0.568 1.497,1.046 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 0.595,1.45 1.014,1.592 0.420,0.142 10 CANH 0.466,0.489 0.890,0.631 0.424,0.142 10 CANL 1.045,2.078 1.469,2.220 0.424,0.142 10 CG 2.532,3.14 2.955,3.282 0.424,0.142 10 BAT 0.394,2.696 0.680,2.835 0.286,0.140 10 H19 2.574,1.028 2.841,1.167 0.267,0.140 10 A43

Disconnect the A43 distance control ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A43-8 (CANH) - A43-9 (CANL) Ignition switch off 54 to 69 Ω
A43-8 (CANH) - H19-4 (CG) Ignition switch off 200 Ω or higher
A43-9 (CANL) - H19-4 (CG) Ignition switch off 200 Ω or higher
A43-8 (CANH) - H19-16 (BAT) Ignition switch off 6 kΩ or higher
A43-9 (CANL) - H19-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Distance Control ECU Assembly)
*b Front view of DLC3



OK

REPLACE DISTANCE CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DISTANCE CONTROL ECU ASSEMBLY (CANH, CANL)

35.CONNECT CONNECTOR
a.

Reconnect the H116 No. 3 junction connector.



NEXT

36.CHECK FOR SHORT IN CAN BUS WIRE (NETWORK GATEWAY ECU)
36.CHECK FOR SHORT IN CAN BUS WIRE (NETWORK GATEWAY ECU)
a.
U153817E01
2.573,1.04 2.929,1.177 0.357,0.137 10 H120 1.334,2.154 1.426,2.154 1.426,2.154 1.665,2.524 false 2.219,2.959 2.357,3.208 2.357,3.208 2.497,3.208 false 1.518,1.199 1.22,1.59 1.22,1.59 1.122,1.59 false 1.623,1.199 1.469,1.84 1.469,1.84 1.372,1.84 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 0.624,1.504 1.048,1.646 0.424,0.142 10 CA2H 0.89,1.753 1.314,1.895 0.424,0.142 10 CA2L 1.045,2.078 1.469,2.220 0.424,0.142 10 CG 2.532,3.14 2.955,3.282 0.424,0.142 10 BAT 0.394,2.696 0.680,2.835 0.286,0.140 10 H19

Disconnect the H120 network gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H120-13 (CA2H) - H120-12 (CA2L) Ignition switch off 108 to 132 Ω
H120-13 (CA2H) - H19-4 (CG) Ignition switch off 200 Ω or higher
H120-12 (CA2L) - H19-4 (CG) Ignition switch off 200 Ω or higher
H120-13 (CA2H) - H19-16 (BAT) Ignition switch off 6 kΩ or higher
H120-12 (CA2L) - H19-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Network Gateway ECU)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO NETWORK GATEWAY ECU (CA2H, CA2L)

37.CHECK HARNESS AND CONNECTOR (NETWORK GATEWAY ECU - BATTERY AND BODY GROUND)
a.
U153771E01
2.037,1.295 2.43,1.583 2.43,1.583 2.553,1.583 false 2.215,1.935 2.144,1.935 2.144,1.935 1.929,1.293 false 2.567,1.508 2.956,1.646 0.389,0.137 10 IG2 2.61,0.709 2.999,0.846 0.389,0.137 10 BATT 0.604,0.709 0.993,0.846 0.389,0.137 10 GND 2.234,1.866 2.623,2.004 0.389,0.137 10 IG1 0.501,1.136 0.858,1.273 0.357,0.137 10 H120 0.07,0.056 0.371,0.193 0.301,0.137 10 *a 1.35,1.097 1.101,0.786 1.101,0.786 1.029,0.786 false 2.278,1.097 2.527,0.786 2.527,0.786 2.598,0.786 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the H120 network gateway ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage :
Tester Connection Condition Specified Condition
H120-2 (BATT) - Body ground Always 11 to 14 V
H120-10 (IG1) - Body ground Ignition switch ON 11 to 14 V
H120-9 (IG2) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H120-4 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Rear view of wire harness connector
(to Network Gateway ECU)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR