Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM
RM27L0U _58 Vehicle Interior _049337 THEFT DETERRENT / KEYLESS ENTRY _0235822 ENGINE IMMOBILISER SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  Key Cannot be Registered  


DESCRIPTION

A maximum of 5 master key ID codes and 3 sub key ID codes can be registered.

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly is replaced, refer to Registration (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>REGISTRATION).


·

When using the Techstream with the vehicle ignition switch off, connect the Techstream to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.



PROCEDURE

1.CHECK REGISTRATION MODE
a.

Check that the system enters registration mode.

OK:

System enters registration mode.




OK

2.CHECK SECURITY INDICATOR LIGHT OPERATION

NG

5.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
2.CHECK SECURITY INDICATOR LIGHT OPERATION
a.

In registration mode, insert the key into the ignition key cylinder and check the security indicator light.

HINT:

If the new key ID code registration fails, code 2-1 will be output through the security light. Trying to re-register an already registered key will cause code 2-2 to be output when the key is inserted. If the number of registered key ID codes exceeds the maximum limit, code 2-3 will be output through the security indicator light. The output details are shown in the following illustration.


U153152E04
0.302,1.313 1.667,1.865 1.365,0.552 10 false Normal (Engine immobiliser system is operating normally) 0.333,3.292 1.021,3.531 0.688,0.24 10 false Code 2-1 0.333,5.385 1.063,5.625 0.729,0.24 10 false Code 2-2 0.333,7.49 1.323,7.74 0.99,0.25 10 false Code 2-3 1.865,0.781 3,0.99 1.135,0.208 10 false 0.12 seconds 2.729,2.125 3.781,2.323 1.052,0.198 10 false 1.88 seconds 1.813,1.292 2.073,1.5 0.26,0.208 10 false On 1.813,1.74 2.135,1.99 0.323,0.25 10 false Off 1.802,3.146 2.052,3.396 0.25,0.25 10 false On 1.813,3.594 2.135,3.875 0.323,0.281 10 false Off 1.823,5.25 2.104,5.49 0.281,0.24 10 false On 1.823,5.677 2.156,5.927 0.333,0.25 10 false Off 1.885,2.667 2.771,2.833 0.885,0.167 10 false 0.25 seconds 1.51,8.26 2.365,8.438 0.854,0.177 10 false 0.25 seconds 3.094,8.26 3.906,8.427 0.813,0.167 10 false 0.5 seconds 1.5,6.167 2.354,6.344 0.854,0.177 10 false 0.25 seconds 3.094,6.177 3.906,6.344 0.813,0.167 10 false 0.5 seconds 1.5,4.083 2.354,4.26 0.854,0.177 10 false 0.25 seconds 3.094,4.083 3.906,4.25 0.813,0.167 10 false 0.5 seconds 3.354,2.688 4,2.833 0.646,0.146 10 false 1 second 1.813,7.333 2.104,7.583 0.292,0.25 10 false On 1.823,7.792 2.188,8.021 0.365,0.229 10 false Off 1.885,4.771 2.76,5.021 0.875,0.25 10 false 0.25 seconds 3.729,4.76 4.365,4.927 0.635,0.167 10 false 1 second 1.917,6.854 2.792,7.01 0.875,0.156 10 false 0.25 seconds 4.073,6.854 4.698,7.021 0.625,0.167 10 false 1 second 0.156,0.156 1.708,0.354 1.552,0.198 10 false Security Indicator Light:

Result
Result Proceed to
Code 2-1 or code 2-3 is output A
Code 2-2 is output B



A

3.READ VALUE USING TECHSTREAM (TRANSPONDER S-CODE, TRANSPONDER M-CODE)

B

END (REGISTERED KEY WAS USED)

3.READ VALUE USING TECHSTREAM (TRANSPONDER S-CODE, TRANSPONDER M-CODE)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Immobiliser / Data List.


e.

Read the Data List according to the display on the Techstream.

Immobiliser
Tester Display Measurement Item / Range Normal Condition Diagnostic Note
Transponder S-code Number of registered sub key / min. 0, max. 15 Number of registered sub key -
Transponder M-code Number of registered master key / min. 0, max. 15 Number of registered master key -

Result
Result Proceed to
5 is displayed for "Transponder M-code" and 0 is displayed for "Transponder S-code" A
0 is displayed for "Transponder M-code" and 3 is displayed for "Transponder S-code" B
5 is displayed for "Transponder M-code" and 3 is displayed for "Transponder S-code" C
Values are other than above D



A

KEY REGISTRATION (SUB-KEY)

B

KEY REGISTRATION (MASTER KEY)

C

MAXIMUM NUMBER OF KEYS ALREADY REGISTERED

D

4.KEY REGISTRATION
4.KEY REGISTRATION
a.

Refer to the table below to determine if additional keys can be registered.

Number of Keys Registered (Master and Sub) Proceed to
0 New key ID code registration
1 to 7 Additional key ID code registration


b.

Check if an additional key can be registered.

OK:

Additional key can be registered.




OK

END (KEY MALFUNCTION)

NG

5.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.

Remove the unlock warning switch assembly (See page Vehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL).


b.

Inspect the unlock warning switch assembly (See page Vehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>INSPECTION).



OK

6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - UNLOCK WARNING SWITCH ASSEMBLY)

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - UNLOCK WARNING SWITCH ASSEMBLY)
a.

Disconnect the H21 unlock warning switch assembly connector.


b.

Disconnect the H32 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H21-1 - H32-3 (KSW) Always Below 1 Ω
H21-2 - Body ground Always Below 1 Ω
H21-1 - Body ground Always 10 kΩ or higher
H32-3 (KSW) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR