Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM
RM27L0U _58 Vehicle Interior _049341 SUPPLEMENTAL RESTRAINT SYSTEMS _0235847 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1771  Passenger Side Buckle Switch Circuit Malfunction  


DESCRIPTION

The passenger side buckle switch circuit consists of the occupant classification ECU and the front seat inner belt RH.

DTC B1771 is stored when a malfunction is detected in the passenger side buckle switch circuit.

Troubleshoot DTC B1771 first when DTCs B1771 and B1795 are output simultaneously.

DTC Code DTC Detection Condition Trouble Area
B1771 One of following conditions is met:
·

Occupant classification ECU detects line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to +B signal in passenger side buckle switch circuit for 2 seconds

·

Passenger side buckle switch malfunction

·

Occupant classification ECU malfunction


·

Front seat wire RH (w/ Power seat)

·

No. 2 floor wire (w/ Manual seat)

·

Front seat inner belt RH (Passenger side buckle switch)

·

Occupant classification ECU



HINT:
·

When DTC B1650/32 is detected as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1771 of the occupant classification system.

·

Use the Techstream to check for DTCs of the occupant classification ECU, otherwise the DTC cannot be read.



WIRING DIAGRAM

E145805E05
5.615,0.938 5.844,1.135 0.229,0.198 10 false 9*1 5.927,2.719 6.458,2.917 0.531,0.198 10 false BGND 5.927,1.125 6.385,1.323 0.458,0.198 10 false BSW 5.604,1.167 5.854,1.365 0.25,0.198 10 false W6 5.615,2.521 5.844,2.719 0.229,0.198 10 false 5*1 5.604,2.76 5.854,2.958 0.25,0.198 10 false W6 5.271,0.938 5.521,1.135 0.25,0.198 10 false 9*2 5.229,1.167 5.542,1.365 0.313,0.198 10 false P14 5.271,2.521 5.521,2.719 0.25,0.198 10 false 5*2 5.229,2.76 5.542,2.958 0.313,0.198 10 false P14 2.927,0.938 3.156,1.135 0.229,0.198 10 false 2*2 2.594,1.167 2.844,1.365 0.25,0.198 10 false W7 2.927,2.521 3.156,2.719 0.229,0.198 10 false 1*2 2.583,2.76 2.833,2.958 0.25,0.198 10 false W7 2.583,0.938 2.833,1.135 0.25,0.198 10 false 2*1 2.896,1.167 3.208,1.365 0.313,0.198 10 false P15 2.583,2.521 2.833,2.719 0.25,0.198 10 false 1*1 2.906,2.76 3.219,2.958 0.313,0.198 10 false P15 2.115,2.625 2.51,2.823 0.396,0.198 10 false RBE- 2.115,1.042 2.573,1.24 0.458,0.198 10 false RBE+ 0.51,4.073 2.563,4.552 2.052,0.479 10 false Front Seat Inner Belt RH (Passenger Side Buckle Switch) 0.063,4.948 1.365,5.146 1.302,0.198 10 false *1: for Power Seat 0.063,5.208 1.365,5.406 1.302,0.198 10 false *2: for Manual Seat 5.292,4.073 7.146,4.281 1.854,0.208 10 false Occupant Classification ECU

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:
·

If troubleshooting (wire harness inspection) is difficult to perform, remove the front seat RH installation bolts to see the undersurface of the seat cushion.

·

In the above case, hold the seat so that it does not fall down. Holding the seat for a long period of time may cause a problem, such as seat rail deformation. Hold the seat up only for as long as necessary.



PROCEDURE

1.CHECK FOR DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Clear the DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

HINT:

First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1771 is not output.


HINT:

Codes other than DTC B1771 may be output at this time, but they are not related to this check.




OK

NG

2.CHECK CONNECTION OF CONNECTOR
2.CHECK CONNECTION OF CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the occupant classification ECU and the front seat inner belt RH.

OK:

Connectors are properly connected.




OK

3.CHECK CONNECTOR

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTOR
a.

Disconnect the connectors from the occupant classification ECU and the front seat inner belt RH.


b.

Check that the connectors (on the occupant classification ECU side and front seat inner belt RH side) are not damaged (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

OK:

Connectors are not deformed or damaged.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

Result
Result Proceed to
OK A
NG (w/ Power seat) B
NG (w/ Manual seat) C




A

4.CHECK HARNESS AND CONNECTOR (OCCUPANT CLASSIFICATION ECU - FRONT SEAT INNER BELT RH)

B

REPLACE FRONT SEAT WIRE RH

C

REPLACE NO. 2 FLOOR WIRE

4.CHECK HARNESS AND CONNECTOR (OCCUPANT CLASSIFICATION ECU - FRONT SEAT INNER BELT RH)
U154051E02
1.292,0.802 1.24,0.802 1.24,0.802 1.115,1.573 false 6.25,1.271 6.656,0.844 true 6.031,1.385 6.698,1.698 true 3.969,1.74 4.156,2.042 false 1.354,1.031 2.385,1.208 1.031,0.177 10 false No. 2 Floor Wire 1.354,0.75 2.615,0.927 1.26,0.177 10 false Front Seat Wire RH 0.635,1.531 0.771,1.708 0.135,0.177 10 false D 1.74,1.531 1.875,1.708 0.135,0.177 10 false A 0.938,1.729 1.073,1.906 0.135,0.177 10 false C 1.406,1.729 1.542,1.906 0.135,0.177 10 false B 1.292,2.094 2.781,2.5 1.49,0.406 10 false Occupant Classification ECU 0.031,1.896 1.063,2.25 1.031,0.354 10 false Front Seat Inner Belt RH 3.188,1.781 4.052,2 0.865,0.219 10 false Connector C 2.896,1.25 3.198,1.427 0.302,0.177 10 false P15 4.99,1.406 5.292,1.583 0.302,0.177 10 false P14 2.917,0.917 3.146,1.094 0.229,0.177 10 false W7 2.594,0.708 2.75,0.885 0.156,0.177 10 false *1 2.396,1 2.573,1.177 0.177,0.177 10 false *2 3.26,0.917 3.417,1.094 0.156,0.177 10 false *1 3.26,1.229 3.438,1.406 0.177,0.177 10 false *2 4.188,1.99 5.031,2.208 0.844,0.219 10 false Service Wire 5.708,1.76 6.573,1.979 0.865,0.219 10 false Connector B 6.708,0.719 7.156,0.938 0.448,0.219 10 false BGND 6.75,1.667 7.104,1.885 0.354,0.219 10 false BSW 2.26,0.031 4.646,0.385 2.385,0.354 10 false Front view of wire harness connector: (to Front Seat Inner Belt RH) 4.75,0.031 7.115,0.385 2.365,0.354 10 false Front view of wire harness connector: (to Occupant Classification ECU) 5,1.083 5.229,1.26 0.229,0.177 10 false W6 5.344,1.083 5.5,1.26 0.156,0.177 10 false *1 5.885,2.073 7.146,2.25 1.26,0.177 10 false *1: for Power Seat 5.885,2.354 7.146,2.531 1.26,0.177 10 false *2: for Manual Seat 5.344,1.396 5.521,1.573 0.177,0.177 10 false *2

a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for Power Seat
Tester Connection Switch Condition Specified Condition
W6-9 (BSW) - Body ground Ignition switch ON Below 1 V
W6-5 (BGND) - Body ground

for Manual Seat
Tester Connection Switch Condition Specified Condition
P14-9 (BSW) - Body ground Ignition switch ON Below 1 V
P14-5 (BGND) - Body ground



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 1 (RBE-) and 2 (RBE+) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Power Seat
Tester Connection Condition Specified Condition
W6-9 (BSW) - W6-5 (BGND) Always Below 1 Ω

for Manual Seat
Tester Connection Condition Specified Condition
P14-9 (BSW) - P14-5 (BGND) Always Below 1 Ω



h.

Disconnect the service wire from connector C.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Power Seat
Tester Connection Condition Specified Condition
W6-9 (BSW) - Body ground Always 1 MΩ or higher
W6-5 (BGND) - Body ground
W6-9 (BSW) - W6-5 (BGND)

for Manual Seat
Tester Connection Condition Specified Condition
P14-9 (BSW) - Body ground Always 1 MΩ or higher
P14-5 (BGND) - Body ground
P14-9 (BSW) - P14-5 (BGND)


Result
Result Proceed to
OK A
NG (w/ Power seat) B
NG (w/ Manual seat) C



A

5.CHECK FOR DTC

B

REPLACE FRONT SEAT WIRE RH

C

REPLACE NO. 2 FLOOR WIRE

5.CHECK FOR DTC
a.

Connect the connectors to the occupant classification ECU and the front seat inner belt RH.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

HINT:

First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1771 is not output.


HINT:

Codes other than DTC B1771 may be output at this time, but they are not related to this check.




OK

NG

6.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH (PASSENGER SIDE BUCKLE SWITCH)
6.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH (PASSENGER SIDE BUCKLE SWITCH)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the front seat inner belt RH (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).

HINT:

Perform the inspection using parts from a normal vehicle when possible.



d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Clear the DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

HINT:

First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1771 is not output.


HINT:

Codes other than DTC B1771 may be output at this time, but they are not related to this check.




OK

END

NG

8.REPLACE OCCUPANT CLASSIFICATION ECU
8.REPLACE OCCUPANT CLASSIFICATION ECU
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the occupant classification ECU.


HINT:

Perform the inspection using parts from a normal vehicle when possible.



d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Clear the DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

HINT:

If the DTCs are not cleared at this time, past DTCs will remain.




NEXT

9.PERFORM ZERO POINT CALIBRATION
9.PERFORM ZERO POINT CALIBRATION
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


c.

Using the Techstream, perform the zero point calibration (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).



NEXT

10.PERFORM SENSITIVITY CHECK
10.PERFORM SENSITIVITY CHECK
a.

Using the Techstream, perform the sensitivity check (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

Standard range:

27 to 33 kg (59.5 to 72.8 lb)




NEXT

END