Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM
RM27L0U _58 Vehicle Interior _049341 SUPPLEMENTAL RESTRAINT SYSTEMS _0235847 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1790  Center Airbag Sensor Assembly Communication Circuit Malfunction  


DESCRIPTION

The center airbag sensor communication circuit consists of the occupant classification ECU and the center airbag sensor.

DTC B1790 is stored when a malfunction is detected in the center airbag sensor communication circuit.

DTC Code DTC Detection Condition Trouble Area
B1790 One of following conditions is met:
·

Occupant classification ECU receives line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to +B signal in center airbag sensor communication circuit for 2 seconds

·

Center airbag sensor malfunction

·

Occupant classification ECU malfunction


·

No. 2 floor wire

·

Front seat wire RH (for Power seat)

·

Occupant classification ECU

·

Center airbag sensor assembly



HINT:
·

When DTC B1630/32 is detected as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1790 of the occupant classification system.

·

Use the Techstream to check for DTCs of the occupant classification ECU, otherwise the DTCs cannot be read.



WIRING DIAGRAM

C158891E05
1.896,3.573 2.198,3.75 0.302,0.177 10 false P14 2.365,3.573 2.844,3.75 0.479,0.177 10 false W6 2.365,1.656 2.688,1.833 0.323,0.177 10 false W6 1.906,1.667 2.208,1.844 0.302,0.177 10 false P14 3.771,3.573 4.104,3.76 0.333,0.188 10 false PW1 3.76,1.677 4.094,1.865 0.333,0.188 10 false PW1 5.073,1.583 5.292,1.729 0.219,0.146 10 false 12 5.042,3.479 5.26,3.625 0.219,0.146 10 false 13 5.438,1.646 5.833,1.823 0.396,0.177 10 false FSP+ 5.448,3.573 5.844,3.75 0.396,0.177 10 false FSP- 1.396,1.625 1.792,1.802 0.396,0.177 10 false FSR+ 1.396,3.583 1.792,3.76 0.396,0.177 10 false FSR- 5.292,4.646 5.552,4.802 0.26,0.156 10 false P1 5.271,4.813 6.646,4.969 1.375,0.156 10 false Center Airbag Sensor 0.521,4.781 2.375,4.938 1.854,0.156 10 false Occupant Classification ECU 3.854,2.302 4.031,2.49 0.177,0.188 10 false *2 3.844,4.229 4.021,4.417 0.177,0.188 10 false *2 3.813,1.448 4.073,1.625 0.26,0.177 10 false 8*1 3.802,3.354 4.063,3.531 0.26,0.177 10 false 9*1 0.146,5.219 1.344,5.396 1.198,0.177 10 false *1: w/ Power Seat 0.146,5.469 1.438,5.646 1.292,0.177 10 false *2: w/o Power Seat 1.917,1.417 2.146,1.604 0.229,0.188 10 false 8*2 2.354,1.406 2.583,1.594 0.229,0.188 10 false 8*1 1.927,3.323 2.156,3.51 0.229,0.188 10 false 4*2 2.375,3.323 2.604,3.51 0.229,0.188 10 false 4*1

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:
·

If troubleshooting (wire harness inspection) is difficult to perform, remove the front RH seat installation bolts to see the undersurface of the seat cushion.

·

In the above case, hold the seat so that it does not fall down. Holding the seat for a long period of time may cause problems, such as seat rail deformation. Hold the seat up only for as long as necessary.



PROCEDURE

1.CHECK FOR DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Clear any DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

HINT:
·

First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

·

Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.




c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Using the Techstream, check for DTCs of the occupant classification ECU (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1790 is not output.


HINT:

DTCs other than DTC B1790 may be output at this time, but they are not related to this check.




OK

NG

2.CHECK CONNECTION OF CONNECTOR
2.CHECK CONNECTION OF CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the occupant classification ECU and the center airbag sensor.

OK:

Connectors are properly connected.




OK

3.CHECK CONNECTOR

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTOR
a.

Check that the connectors (on the center airbag sensor side and occupant classification ECU side) are not damaged (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

OK:

Connectors are not deformed or damaged.


Result
Result Proceed to
Connectors are not deformed or damaged (for Power seat) A
Connectors are not deformed or damaged (for Manual seat) B
Connectors are deformed or damaged C



A

4.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT

B

11.CHECK NO. 2 FLOOR WIRE

C

REPLACE HARNESS OR CONNECTOR

4.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT
C353058E02
4.375,0.719 4.708,0.979 0.333,0.26 4.354,1.927 4.688,2.188 0.333,0.26 4.979,1.188 5.24,1 true 5.781,1.219 5.396,0.906 true 5.073,2.552 5.375,2.344 true 5.76,2.271 5.458,2.344 true 5.76,2.615 5.542,2.573 true 2.156,1.563 3.021,2.167 0.865,0.604 10 false Center Airbag Sensor 0.406,1.792 1.896,2.292 1.49,0.5 10 false Occupant Classification ECU 1.219,1.313 1.375,1.51 0.156,0.198 10 false F 1.5,1.083 1.656,1.281 0.156,0.198 10 false E 1.74,1.094 2.198,1.292 0.458,0.198 10 false D C 2.063,1.094 2.219,1.292 0.156,0.198 10 false B 2.344,1.313 2.5,1.51 0.156,0.198 10 false A 4.208,0.104 6.542,0.719 2.333,0.615 10 false Front view of wire harness connector: (to Occupant Classification ECU) 4.448,0.76 4.76,0.958 0.313,0.198 10 false W6 5.927,0.833 6.729,1.031 0.802,0.198 10 false Connector E 4.75,1.188 5.365,1.385 0.615,0.198 10 false FSR+ 5.719,1.25 6.333,1.448 0.615,0.198 10 false FSR- 4.208,1.427 6.521,1.969 2.313,0.542 10 false Front view of wire harness connector: (to Center Airbag Sensor) 4.438,1.969 4.75,2.167 0.313,0.198 10 false P1 5.823,1.948 6.625,2.146 0.802,0.198 10 false Connector B 4.688,2.469 5.052,2.667 0.365,0.198 10 false FSP- 5.813,2.167 6.177,2.365 0.365,0.198 10 false FSP+ 5.813,2.542 6.635,2.781 0.823,0.24 10 false Service Wire

a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
W6-8 (FSR+) - Body ground Ignition switch ON Below 1 V
W6-4 (FSR-) - Body ground



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 12 (FSP+) and 13 (FSP-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W6-8 (FSR+) - W6-4 (FSR-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W6-8 (FSR+) - W6-4 (FSR-) Always 1 MΩ or higher
W6-8 (FSR+) - Body ground
W6-4 (FSR-) - Body ground




OK

5.CHECK FOR DTC

NG

10.CHECK FRONT SEAT WIRE RH
5.CHECK FOR DTC
a.

Connect the connectors to the occupant classification ECU and the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear any DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

HINT:
·

First clear any DTCs stored in the occupant classification ECU and then in the center airbag sensor.

·

Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.




e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Using the Techstream, check for DTCs of the occupant classification ECU (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1790 is not output.


HINT:

DTCs other than DTC B1790 may be output at this time, but they are not related to this check.




OK

NG

6.REPLACE OCCUPANT CLASSIFICATION ECU
6.REPLACE OCCUPANT CLASSIFICATION ECU
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the occupant classification ECU (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL).

HINT:

Perform the inspection using parts from a normal vehicle when possible.




NEXT

7.PERFORM ZERO POINT CALIBRATION
7.PERFORM ZERO POINT CALIBRATION
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Using the Techstream, perform the zero point calibration (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).



NEXT

8.PERFORM SENSITIVITY CHECK
8.PERFORM SENSITIVITY CHECK
a.

Using the Techstream, perform the sensitivity check (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

Standard range:

27 to 33 kg (59.5 to 72.8 lb)




NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Connect the connector to the occupant classification ECU.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear any DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

HINT:
·

First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

·

Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.




e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Using the Techstream, check for DTCs of the occupant classification ECU (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1790 is not output.


HINT:

DTCs other than DTC B1790 may be output at this time, but they are not related to this check.




OK

END

NG

10.CHECK FRONT SEAT WIRE RH
a.

Disconnect the front seat wire RH connector from the No. 2 floor wire.

E344965E01
3.01,0.542 3.344,0.781 0.333,0.24 5.042,0.531 5.417,0.771 0.375,0.24 1.365,0.74 1.365,0.208 1.365,0.208 1.271,0.208 false 1.625,0.823 1.625,1.438 1.625,1.438 1.74,1.438 false 3.458,1.344 3.823,1.083 false 4.427,1.354 4.01,1.031 false 6.313,1.385 5.938,1.115 true 5.469,1.375 5.833,1.115 true 0.063,0.104 2.813,0.302 2.75,0.198 10 false Front Seat Wire RH 0.458,1.042 1.688,1.24 1.229,0.198 10 false Occupant 1.813,0.927 2.646,1.292 0.833,0.365 10 false Center Airbag Sensor 0.458,1.219 1.292,1.583 0.833,0.365 10 false Classification ECU 1.802,1.344 4.25,1.542 2.448,0.198 10 false No. 2 Floor Wire 2.604,0.021 4.875,0.781 2.271,0.76 10 false Front view of wire harness connector: (to Occupant Classification ECU) 4.448,0.927 6.135,1.125 1.688,0.198 10 false Connector E 3.073,0.594 3.385,0.792 0.313,0.198 10 false W6 3.104,1.323 3.719,1.521 0.615,0.198 10 false FSR+ 4.479,1.302 5.094,1.5 0.615,0.198 10 false FSR- 5.313,1.375 5.927,1.573 0.615,0.198 10 false FSP- 6.25,1.396 6.865,1.594 0.615,0.198 10 false FSP+ 4.99,0.021 7.146,0.833 2.156,0.813 10 false Front view of wire harness connector: (to Front Seat Wire RH) 6.354,0.948 7.156,1.177 0.802,0.229 10 false Connector D 5.083,0.573 5.542,0.771 0.458,0.198 10 false PW1 0.896,0.698 1.052,0.896 0.156,0.198 10 false F 1.167,0.521 1.323,0.719 0.156,0.198 10 false E 1.427,0.521 1.583,0.719 0.156,0.198 10 false D 1.521,0.521 1.677,0.719 0.156,0.198 10 false C 1.708,0.521 1.865,0.719 0.156,0.198 10 false B 1.979,0.688 2.135,0.885 0.156,0.198 10 false A


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
PW1-8 (FSP+) - Body ground Ignition switch ON Below 1 V
PW1-9 (FSP-) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the connector from the occupant classification ECU.


g.

Using a service wire, connect terminals 8 (FSR+) and 4 (FSR-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of connector.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
PW1-8 (FSP+) - PW1-9 (FSP-) Always Below 1 Ω



i.

Disconnect the service wire from connector E.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
PW1-8 (FSP+) - PW1-9 (FSP-) Always 1 MΩ or higher
PW1-8 (FSP+) - Body ground
PW1-9 (FSP-) - Body ground




OK

REPLACE NO. 2 FLOOR WIRE

NG

REPLACE FRONT SEAT WIRE RH

11.CHECK NO. 2 FLOOR WIRE
E344966E01
2.802,0.656 3.208,0.906 0.406,0.25 4.865,0.646 5.208,0.896 0.344,0.25 1.25,0.802 1.25,0.177 1.25,0.177 1.125,0.177 false 3.448,1.5 3.677,1.24 true 4.063,1.51 3.854,1.156 true 5.458,1.49 5.75,1.26 true 5.833,1.271 6.188,1.146 true 5.927,1.51 6.094,1.552 true 0.083,0.083 2.531,0.281 2.448,0.198 10 false No. 2 Floor Wire 0.917,0.563 1.073,0.76 0.156,0.198 10 false C 1.469,0.563 1.615,0.76 0.146,0.198 10 false B 1.719,0.76 1.865,0.958 0.146,0.198 10 false A 0.052,1.219 1.521,1.729 1.469,0.51 10 false Occupant Classification ECU 1.583,1 2.458,1.51 0.875,0.51 10 false Center Airbag Sensor 0.646,0.802 0.802,1 0.156,0.198 10 false D 2.354,0 4.708,0.677 2.354,0.677 10 false Front view of wire harness connector: (to Occupant Classification ECU) 4.802,0.01 7.156,0.688 2.354,0.677 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 2.885,0.698 3.344,0.896 0.458,0.198 10 false P14 4.969,0.688 5.281,0.885 0.313,0.198 10 false P1 4.281,1.083 5.969,1.281 1.688,0.198 10 false Connector C 6.125,0.635 7.052,0.833 0.927,0.198 10 false Connector B 3.208,1.521 3.823,1.719 0.615,0.198 10 false FSR+ 3.938,1.521 4.552,1.719 0.615,0.198 10 false FSR- 5.281,1.5 5.896,1.698 0.615,0.198 10 false FSP- 6.229,1.052 6.844,1.25 0.615,0.198 10 false FSP+ 6.135,1.49 7.063,1.688 0.927,0.198 10 false Service Wire

a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
P14-8 (FSR+) - Body ground Ignition switch ON Below 1 V
P14-4 (FSR-) - Body ground



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 12 (FSP+) and 13 (FSP-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P14-8 (FSR+) - P14-4 (FSR-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P14-8 (FSR+) - P14-4 (FSR-) Always 1 MΩ or higher
P14-8 (FSR+) - Body ground
P14-4 (FSR-) - Body ground




OK

12.CHECK FOR DTC

NG

REPLACE NO. 2 FLOOR WIRE

12.CHECK FOR DTC
a.

Connect the connectors to the occupant classification ECU and the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear any DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

HINT:
·

First clear any DTCs stored in the occupant classification ECU and then in the center airbag sensor.

·

Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.




e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Using the Techstream, check for DTCs of the occupant classification ECU (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1790 is not output.


HINT:

DTCs other than DTC B1790 may be output at this time, but they are not related to this check.




OK

NG

13.REPLACE OCCUPANT DETECTION ECU
13.REPLACE OCCUPANT DETECTION ECU
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the occupant classification ECU (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL).

HINT:

Perform the inspection using parts from a normal vehicle when possible.




NEXT

14.PERFORM ZERO POINT CALIBRATION
14.PERFORM ZERO POINT CALIBRATION
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Using the Techstream, perform the zero point calibration (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).



NEXT

15.PERFORM SENSITIVITY CHECK
15.PERFORM SENSITIVITY CHECK
a.

Using the Techstream, perform the sensitivity check (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

Standard range:

27 to 33 kg (59.5 to 72.8 lb)




NEXT

16.CHECK FOR DTC
16.CHECK FOR DTC
a.

Connect the connector to the occupant classification ECU.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear any DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

HINT:
·

First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

·

Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.




e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Using the Techstream, check for DTCs of the occupant classification ECU (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1790 is not output.


HINT:

DTCs other than DTC B1790 may be output at this time, but they are not related to this check.




OK

END

NG