Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27L0U _58 Vehicle Interior _049341 SUPPLEMENTAL RESTRAINT SYSTEMS _0235848 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1810/53  Short in Driver Side Squib 2nd Step Circuit  B1811/53  Open in Driver Side Squib 2nd Step Circuit  B1812/53  Short to GND in Driver Side Squib 2nd Step Circuit  B1813/53  Short to B+ in Driver Side Squib 2nd Step Circuit  


DESCRIPTION

The driver side squib 2nd step circuit consists of the center airbag sensor, the spiral cable, and the steering pad.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver side squib 2nd step circuit.

DTC Code Detection Condition Trouble Area
B1810/53 When one of following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the driver side squib 2nd step circuit during primary check.

·

Driver side squib 2nd step malfunction

·

Spiral cable malfunction

·

Center airbag sensor malfunction


·

Instrument panel wire

·

Spiral cable

·

Steering pad (Driver side squib 2nd step)

·

Center airbag sensor assembly


B1811/53 When one of following conditions is met:
·

The center airbag sensor receives an open circuit signal in the driver side squib 2nd step circuit for 2 seconds.

·

Driver side squib 2nd step malfunction

·

Spiral cable malfunction

·

Center airbag sensor malfunction


·

Instrument panel wire

·

Spiral cable

·

Steering pad (Driver side squib 2nd step)

·

Center airbag sensor assembly


B1812/53 When one of following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the driver side 2nd step circuit for 0.5 seconds.

·

Driver side squib 2nd step malfunction

·

Spiral cable malfunction

·

Center airbag sensor malfunction


·

Instrument panel wire

·

Spiral cable

·

Steering pad (Driver side squib 2nd step)

·

Center airbag sensor assembly


B1813/53 When one of following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the driver side squib 2nd step circuit for 0.5 seconds.

·

Driver side squib 2nd step malfunction

·

Spiral cable malfunction

·

Center airbag sensor malfunction


·

Instrument panel wire

·

Spiral cable

·

Steering pad (Driver side squib 2nd step)

·

Center airbag sensor assembly



WIRING DIAGRAM

U153616E01
2.875,1.566 3.213,1.722 0.338,0.156 10 D2+ 2.91,2.407 3.217,2.562 0.308,0.156 10 D2- 4.794,1.664 5.136,1.820 0.342,0.156 10 D2+ 4.794,2.505 5.102,2.660 0.308,0.156 10 D2- 3.232,1.769 3.457,1.960 0.225,0.191 10 4 3.232,2.617 3.408,2.807 0.177,0.191 10 3 2.825,2.995 3.099,3.158 0.274,0.163 10 H13 2.825,3.15 3.634,3.320 0.809,0.170 10 Spiral Cable 0.766,3.178 2.478,3.344 1.713,0.165 10 Driver Side Squib 2nd Step 4.591,1.552 4.754,1.791 0.163,0.239 10 8 4.591,2.385 4.830,2.611 0.239,0.225 10 7 4.78,4.179 5.068,4.321 0.288,0.142 10 H56 4.78,4.341 6.166,4.511 1.386,0.170 10 Center Airbag Sensor 0.769,3.012 1.127,3.174 0.358,0.162 10 z8 2.279,1.517 2.505,1.708 0.225,0.191 10 2 2.279,2.365 2.456,2.555 0.177,0.191 10 1

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:
·

Perform the simulation method by selecting "check mode" (signal check) with the Techstream (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).



PROCEDURE

1.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connector is properly connected to the steering pad.

OK:

The connector is properly connected.


HINT:

If the connector is not connected securely, reconnect the connector and proceed to the next inspection.



d.

Disconnect the connector from the steering pad.


e.

Check that the spiral cable connector (on the steering pad side) is not damaged.

OK:

The lock button is not disengaged, or the claw of the lock is not deformed or damaged.




OK

2.CHECK STEERING PAD (DRIVER SIDE SQUIB 2ND STEP)

NG

2.CHECK STEERING PAD (DRIVER SIDE SQUIB 2ND STEP)
a.
U138555E02
0.208,0.677 0.208,0.115 0.208,0.115 1.25,0.115 false 1.875,3.813 2.177,4.063 false 2.115,3.26 2.448,3.552 false 1.313,0.052 3.052,0.229 1.74,0.177 10 false Driver Side Squib 2nd Step 0.781,1.188 1.594,1.344 0.813,0.156 10 false Spiral Cable 2,1.552 3.365,1.708 1.365,0.156 10 false Center Airbag Sensor 0.365,2.083 2.76,2.448 2.396,0.365 10 false Front view of wire harness connector: (to Driver Side Squib 2nd Step) 0.25,3.073 1.083,3.323 0.833,0.25 10 false Connector E 0.667,3.469 0.885,3.635 0.219,0.167 10 false z8 2.531,3.51 2.896,3.688 0.365,0.177 10 false SST 2.271,4.094 3.188,4.302 0.917,0.208 10 false Color: Black 0.344,0.917 0.479,1.115 0.135,0.198 10 false F 0.531,0.917 0.667,1.115 0.135,0.198 10 false E 1.698,0.917 1.833,1.115 0.135,0.198 10 false D 1.823,0.917 1.958,1.115 0.135,0.198 10 false C

Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (black connector).

CAUTION:

Never connect the tester to the steering pad (driver side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1810, B1811, B1812, B1813 or 53 is not output.


HINT:

Codes other than DTC B1810, B1811, B1812, B1813 and 53 may be output at this time, but they are not related to this check.




OK

NG

3.CHECK CONNECTOR
3.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector E.


d.

Check that the connector is properly connected to the center airbag sensor assembly.

OK:

The connector is properly connected.


HINT:

If the connector is not connected securely, reconnect the connector and proceed to the next inspection.



e.

Disconnect the connector from the center airbag sensor assembly.


f.

Check that the terminal of the connector is not damaged.

OK:

The terminal is not deformed or damaged.



g.

Check that the short spring for the instrument panel wire connector with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.




OK

4.CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT
a.
U138557E02
0.198,0.771 0.198,0.177 0.198,0.177 1.229,0.177 false 1.781,3.208 2.094,3.51 false 1.677,3.198 1.344,3.49 false 1.948,3.917 2.281,4.208 false 1.292,0.115 3.021,0.292 1.729,0.177 10 false Driver Side Squib 2nd Step 0.802,1.271 1.604,1.448 0.802,0.177 10 false Spiral Cable 2.021,1.635 3.396,1.781 1.375,0.146 10 false Center Airbag Sensor 0.385,2.229 2.781,2.594 2.396,0.365 10 false Front view of wire harness connector: (to Driver Side Squib 2nd Step) 2.188,2.885 3.021,3.135 0.833,0.25 10 false Connector E 0.667,3.521 0.865,3.688 0.198,0.167 10 false z8 2.198,4.26 3.115,4.469 0.917,0.208 10 false Color: Black 0.344,1 0.479,1.198 0.135,0.198 10 false F 0.542,1 0.677,1.198 0.135,0.198 10 false E 1.688,0.99 1.823,1.188 0.135,0.198 10 false D 1.823,0.99 1.958,1.188 0.135,0.198 10 false C 2.188,0.99 2.323,1.188 0.135,0.198 10 false B 2.583,0.75 2.719,0.948 0.135,0.198 10 false A 1.188,3.521 1.458,3.698 0.271,0.177 10 false D2- 2.063,3.531 2.406,3.708 0.344,0.177 10 false D2+

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z8-2 (D2+) - Body ground Ignition switch ON Below 1 V
z8-1 (D2-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z8-2 (D2+) - z8-1 (D2-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z8-2 (D2+) - z8-1 (D2-) Always 1 MΩ or higher
z8-2 (D2+) - Body ground Always 1 MΩ or higher
z8-1 (D2-) - Body ground Always 1 MΩ or higher




OK

5.CHECK CENTER AIRBAG SENSOR

NG

6.CHECK CONNECTOR
5.CHECK CENTER AIRBAG SENSOR
a.
C158846E15
0.333,0.75 0.375,1.781 false 0.208,1.771 1.99,1.948 1.781,0.177 10 false Driver Side Squib 2nd Step 0.708,1.156 1.563,1.313 0.854,0.156 10 false Spiral Cable 1.813,1.448 3.219,1.604 1.406,0.156 10 false Center Airbag Sensor 0.563,0.813 0.75,1 0.188,0.188 10 false E 0.438,0.823 0.625,1.01 0.188,0.188 10 false F 1.75,0.823 1.938,1.01 0.188,0.188 10 false C 1.635,0.823 1.823,1.01 0.188,0.188 10 false D

Restore the released activation prevention mechanism of connector B to the original condition.


b.

Connect the connectors to the steering pad and the center airbag sensor.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1810, B1811, B1812, B1813 or 53 is not output.


HINT:

Codes other than DTC B1810, B1811, B1812, B1813 and 53 may be output at this time, but they are not related to this check.




OK

NG

6.CHECK CONNECTOR
a.

Restore the released activation prevention mechanism of connector B to the original condition.


b.

Check that the connectors that link the spiral cable and instrument panel wire harness are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



c.

Disconnect the connectors that link the spiral cable and instrument panel wire.


d.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



e.

Check that the short spring for the spiral cable connector with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.




OK

7.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - SPIRAL CABLE)

NG

REPLACE SPIRAL CABLE OR INSTRUMENT PANEL WIRE

7.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - SPIRAL CABLE)
a.
U138559E02
1.438,3.292 1.01,3.688 false 1.635,3.281 2.115,3.677 false 0.271,0.146 0.135,0.146 0.135,0.146 0.135,0.948 false 1.708,0.406 3.146,0.583 1.438,0.177 10 false Instrument Panel Wire 0.302,0.073 2.063,0.24 1.76,0.167 10 false Driver Side Squib 2nd Step 0.635,1.406 1.438,1.583 0.802,0.177 10 false Spiral Cable 1.979,1.74 3.344,1.896 1.365,0.156 10 false Center Airbag Sensor 0.219,2.135 2.448,2.49 2.229,0.354 10 false Rear view of wire harness connector: (to Spiral Cable) 2.417,3 3.25,3.198 0.833,0.198 10 false Connector C 0.708,2.917 1.01,3.104 0.302,0.188 10 false H13 0.26,1.156 0.396,1.354 0.135,0.198 10 false F 0.448,1.156 0.583,1.354 0.135,0.198 10 false E 1.49,1.146 1.625,1.344 0.135,0.198 10 false D 1.677,1.146 1.813,1.344 0.135,0.198 10 false C 1.99,1.146 2.125,1.344 0.135,0.198 10 false B 2.323,0.917 2.458,1.115 0.135,0.198 10 false A 0.854,3.719 1.188,3.896 0.333,0.177 10 false D2+ 2.083,3.708 2.333,3.885 0.25,0.177 10 false D2-

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H13-4 (D2+) - Body ground Ignition switch ON Below 1 V
H13-3 (D2-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H13-4 (D2+) - H13-3 (D2-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H13-4 (D2+) - H13-3 (D2-) Always 1 MΩ or higher
H13-4 (D2+) - Body ground Always 1 MΩ or higher
H13-3 (D2-) - Body ground Always 1 MΩ or higher




OK

NG

REPLACE INSTRUMENT PANEL WIRE