Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27L0U _58 Vehicle Interior _049341 SUPPLEMENTAL RESTRAINT SYSTEMS _0235848 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1835/58  Short in Front Passenger Side Curtain Shield Squib Circuit  B1836/58  Open in Front Passenger Side Curtain Shield Squib Circuit  B1837/58  Short to GND in Front Passenger Side Curtain Shield Squib Circuit  B1838/58  Short to B+ in Front Passenger Side Curtain Shield Squib Circuit  


DESCRIPTION

The curtain shield squib RH circuit consists of the center airbag sensor and the curtain shield airbag RH.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the curtain shield squib RH circuit.

DTC Code Detection Condition Trouble Area
B1835/58 When one of following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the curtain shield squib RH circuit during primary check.

·

Curtain shield squib RH malfunction

·

Center airbag sensor malfunction


·

No. 2 floor wire

·

Curtain shield airbag assembly RH (Curtain shield squib RH)

·

Center airbag sensor assembly


B1836/58 When one of following conditions is met:
·

The center airbag sensor receives an open circuit signal in the curtain shield squib RH circuit for 2 seconds.

·

Curtain shield squib RH malfunction

·

Center airbag sensor malfunction


·

No. 2 floor wire

·

Curtain shield airbag assembly RH (Curtain shield squib RH)

·

Center airbag sensor assembly


B1837/58 When one of following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the curtain shield squib RH circuit for 0.5 seconds.

·

Curtain shield squib RH malfunction

·

Center airbag sensor malfunction


·

No. 2 floor wire

·

Curtain shield airbag assembly RH (Curtain shield squib RH)

·

Center airbag sensor assembly


B1838/58 When one of following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the curtain shield squib RH circuit for 0.5 seconds.

·

Curtain shield squib RH malfunction

·

Center airbag sensor malfunction


·

No. 2 floor wire

·

Curtain shield airbag assembly RH (Curtain shield squib RH)

·

Center airbag sensor assembly



WIRING DIAGRAM

C157591E58
1.053,3.534 1.557,3.694 0.504,0.159 10 P2 1.053,3.701 2.980,3.859 1.927,0.159 10 Curtain Shield Squib RH 4.654,4.711 4.936,4.870 0.282,0.159 10 P1 4.682,3.028 5.041,3.187 0.359,0.159 10 ICP- 4.394,3.133 4.583,3.293 0.189,0.159 10 10 4.682,2.187 5.060,2.347 0.378,0.159 10 ICP+ 2.291,2.935 2.599,3.094 0.308,0.159 10 ICR- 2.253,2.094 2.599,2.253 0.346,0.159 10 ICR+ 4.475,2.293 4.584,2.452 0.109,0.159 10 9 2.696,2.321 2.805,2.480 0.109,0.159 10 2 2.696,3.161 2.805,3.321 0.109,0.159 10 1 4.654,4.877 6.033,5.055 1.379,0.177 10 Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:
·

Perform the simulation method by selecting "check mode" (signal check) with the Techstream (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).



PROCEDURE

1.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connector is properly connected to the curtain shield airbag RH.

OK:

The connector is properly connected.


HINT:

If the connector is not connected securely, reconnect the connector and proceed to the next inspection.



d.

Disconnect the connector from the curtain shield airbag RH.


e.

Check that the No. 2 floor wire connector (on the curtain shield airbag RH side) is not damaged.

OK:

The lock button is not disengaged, or the claw of the lock is not deformed or damaged.




OK

2.CHECK CURTAIN SHIELD AIRBAG RH (CURTAIN SHIELD SQUIB RH)

NG

REPLACE NO. 2 FLOOR WIRE

2.CHECK CURTAIN SHIELD AIRBAG RH (CURTAIN SHIELD SQUIB RH)
a.
U153579E02
2.208,3.781 2.521,3.896 false 1.396,1.073 1.115,0.313 false 1.469,1.271 1.604,1.438 0.135,0.167 10 false D 1.667,1.271 1.875,1.458 0.208,0.188 10 false C 2.063,1.354 2.969,1.708 0.906,0.354 10 false Center Airbag Sensor 0.188,0.188 1.104,0.521 0.917,0.333 10 false Curtain Shield Squib RH 0.302,2.208 2.635,2.521 2.333,0.313 10 false Front view of wire harness connector: (to Curtain Shield Squib RH) 0.729,3.344 1.021,3.49 0.292,0.146 10 false P2 2.313,3.302 3.146,3.469 0.833,0.167 10 false Connector C 2.573,3.833 2.927,4 0.354,0.167 10 false SST

Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the curtain shield airbag RH (curtain shield squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1835, B1836, B1837, B1838 or 58 is not output.


HINT:

Codes other than DTC B1835, B1836, B1837, B1838 and 58 may be output at this time, but they are not related to this check.




OK

NG

3.CHECK CONNECTOR
3.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Check that the connector is properly connected to the center airbag sensor assembly.

OK:

The connector is properly connected.


HINT:

If the connector is not connected securely, reconnect the connector and proceed to the next inspection.



e.

Disconnect the connector from the center airbag sensor assembly.


f.

Check that the terminal of the connector is not damaged.

OK:

The terminal is not deformed or damaged.



g.

Check that the short spring for the No. 2 floor wire connector with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.




OK

4.CHECK NO. 2 FLOOR WIRE (CURTAIN SHIELD SQUIB RH CIRCUIT)

NG

REPLACE NO. 2 FLOOR WIRE

4.CHECK NO. 2 FLOOR WIRE (CURTAIN SHIELD SQUIB RH CIRCUIT)
a.
U153580E02
0.958,1.01 0.823,1.396 false 1.698,3.51 1.083,4.021 false 1.854,3.51 2.417,4.063 false 1.583,0.854 1.323,0.406 false 1.063,1.073 1.25,1.229 0.188,0.156 10 false D 1.271,1.073 1.458,1.24 0.188,0.167 10 false C 1.656,1.073 1.844,1.24 0.188,0.167 10 false B 2.021,0.802 2.198,0.979 0.177,0.177 10 false A 1.865,1.156 2.833,1.479 0.969,0.323 10 false Center Airbag Sensor 0.177,1.375 1.094,1.698 0.917,0.323 10 false Curtain Shield Squib RH 0.25,0.271 1.292,0.427 1.042,0.156 10 false No. 2 Floor Wire 0.438,2.438 2.792,2.75 2.354,0.313 10 false Front view of wire harness connector: (to Curtain Shield Squib RH) 2.292,3.313 3.146,3.469 0.854,0.156 10 false Connector C 0.635,3.969 1.031,4.146 0.396,0.177 10 false ICR- 2.521,4 2.917,4.177 0.396,0.177 10 false ICR+ 0.854,3.479 1.156,3.656 0.302,0.177 10 false P2

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
P2-2 (ICR+) - Body ground Ignition switch ON Below 1 V
P2-1 (ICR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P2-2 (ICR+) - P2-1 (ICR-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P2-2 (ICR+) - P2-1 (ICR-) Always 1 MΩ or higher
P2-2 (ICR+) - Body ground Always 1 MΩ or higher
P2-1 (ICR-) - Body ground Always 1 MΩ or higher




OK

5.CHECK CENTER AIRBAG SENSOR

NG

REPLACE NO. 2 FLOOR WIRE

5.CHECK CENTER AIRBAG SENSOR
a.
C146261E12
0.168,1.458 1.120,1.790 0.952,0.332 10 Curtain Shield Squib RH 0.824,1.057 0.652,1.412 false 0.961,1.171 1.089,1.364 0.128,0.193 10 D 1.099,1.171 1.245,1.355 0.147,0.184 10 C 1.654,1.229 3.013,1.394 1.360,0.165 10 Center Airbag Sensor

Restore the released activation prevention mechanism of connector B to the original condition.


b.

Connect the connectors to the curtain shield airbag RH and the center airbag sensor.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1835, B1836, B1837, B1838 or 58 is not output.


HINT:

Codes other than DTC B1835, B1836, B1837, B1838 and 58 may be output at this time, but they are not related to this check.




OK

NG