Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27L0U _58 Vehicle Interior _049341 SUPPLEMENTAL RESTRAINT SYSTEMS _0235848 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1630/23  Driver Side Rear Airbag Sensor Circuit Malfunction  B1635/24  Front Passenger Side Rear Airbag Sensor Circuit Malfunction  


DESCRIPTION

The rear airbag sensor LH or RH consists of the safing sensor, the diagnostic circuit, the lateral deceleration sensor, etc.

If the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether the SRS should be activated.

DTC B1630/23 or B1635/24 is stored when a malfunction is detected in the rear airbag sensor LH or RH circuit.

DTC Code Detection Condition Trouble Area
B1630/23 When one of following conditions is met:
·

Rear airbag sensor LH malfunction

·

Side airbag sensor LH malfunction

·

Center airbag sensor malfunction


·

Rear airbag sensor LH

·

Side airbag sensor LH

·

Center airbag sensor assembly

·

Floor wire

·

Front door wire LH


B1635/24 When one of following conditions is met:
·

Rear airbag sensor RH malfunction

·

Side airbag sensor RH malfunction

·

Center airbag sensor malfunction


·

Rear airbag sensor RH

·

Side airbag sensor RH

·

Center airbag sensor assembly

·

No. 2 Floor wire

·

Front door wire RH



WIRING DIAGRAM

C179187E06
0.087,0.023 1.397,0.280 1.310,0.257 12 for Driver Side: 1.201,0.934 1.607,1.076 0.406,0.142 10 BBL+ 1.201,1.767 1.607,1.909 0.406,0.142 10 BBL- 5.672,0.962 6.078,1.104 0.406,0.142 10 BBD+ 5.684,1.745 6.090,1.924 0.406,0.179 10 BBD- 1.201,3.146 1.621,3.330 0.420,0.184 10 BCL+ 1.201,3.949 1.621,4.133 0.420,0.184 10 BCL- 3.884,3.153 4.304,3.337 0.420,0.184 10 BCL+ 3.884,3.956 4.304,4.140 0.420,0.184 10 BCL- 1.701,0.84 1.857,1.052 0.156,0.211 10 4 1.701,1.653 1.815,1.823 0.114,0.170 10 3 1.701,3.04 1.870,3.177 0.170,0.137 10 1 1.705,3.829 1.866,3.994 0.161,0.165 10 2 3.69,3.838 3.908,4.043 0.218,0.205 10 2 3.683,3.035 3.887,3.191 0.205,0.156 10 1 5.463,0.871 5.677,1.047 0.215,0.177 10 8 5.397,1.662 5.622,1.901 0.225,0.239 10 15 0.528,4.646 0.907,4.816 0.378,0.170 10 M12 3.695,4.646 3.982,4.809 0.288,0.163 10 O3 5.474,4.646 5.748,4.816 0.274,0.170 10 O1 0.528,4.821 2.011,5.005 1.482,0.184 10 Side Airbag Sensor LH 3.709,4.809 5.230,5.008 1.521,0.199 10 Rear Airbag Sensor LH 5.474,4.809 6.888,4.993 1.414,0.184 10 Center Airbag Sensor 2.539,3.168 2.894,3.333 0.355,0.165 10 MO1 2.545,3.948 2.903,4.113 0.357,0.165 10 MO1 2.647,2.933 2.752,3.098 0.105,0.165 10 2 2.63,3.717 2.765,3.921 0.135,0.205 10 1 3.379,0.983 3.794,1.148 0.414,0.165 10 MO1 3.386,1.762 3.760,1.928 0.374,0.165 10 MO1 3.488,0.747 3.593,0.913 0.105,0.165 10 4 3.47,1.531 3.605,1.736 0.135,0.205 10 3

C179187E08
0.083,0.052 1.677,0.271 1.594,0.219 12 false for Passenger Side: 1.198,0.958 1.604,1.104 0.406,0.146 10 false BBR+ 1.198,1.781 1.604,1.927 0.406,0.146 10 false BBR- 5.677,0.969 6.083,1.115 0.406,0.146 10 false BBP+ 5.688,1.76 6.094,1.938 0.406,0.177 10 false BBP- 1.198,3.156 1.615,3.344 0.417,0.188 10 false BCR+ 1.198,3.958 1.615,4.146 0.417,0.188 10 false BCR- 3.885,3.156 4.302,3.344 0.417,0.188 10 false BCR+ 3.885,3.948 4.302,4.135 0.417,0.188 10 false BCR- 1.698,0.813 1.854,1.021 0.156,0.208 10 false 4 1.698,1.625 1.813,1.792 0.115,0.167 10 false 3 1.698,3.01 1.865,3.146 0.167,0.135 10 false 1 1.708,3.802 1.865,3.969 0.156,0.167 10 false 2 3.688,3.802 3.906,4.01 0.219,0.208 10 false 1 3.688,3 3.896,3.156 0.208,0.156 10 false 2 5.458,0.844 5.677,1.021 0.219,0.177 10 false 8 5.396,1.625 5.625,1.865 0.229,0.24 10 false 11 0.531,4.698 0.823,4.865 0.292,0.167 10 false L10 3.719,4.688 4.01,4.854 0.292,0.167 10 false P3 5.458,4.688 5.729,4.854 0.271,0.167 10 false P1 0.531,4.885 2.01,5.073 1.479,0.188 10 false Side Airbag Sensor RH 3.74,4.885 5.271,5.115 1.531,0.229 10 false Rear Airbag Sensor RH 5.458,4.875 6.865,5.063 1.406,0.188 10 false Center Airbag Sensor 2.563,3.188 2.854,3.354 0.292,0.167 10 false LP1 2.573,3.969 2.865,4.135 0.292,0.167 10 false LP1 2.677,2.896 2.781,3.063 0.104,0.167 10 false 2 2.656,3.688 2.792,3.896 0.135,0.208 10 false 1 3.375,1.01 3.667,1.177 0.292,0.167 10 false LP1 3.385,1.802 3.677,1.969 0.292,0.167 10 false LP1 3.49,0.719 3.594,0.885 0.104,0.167 10 false 4 3.469,1.5 3.604,1.708 0.135,0.208 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK FOR DTC
a.

Turn the ignition switch off.


b.

c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1635/24 is output A
DTC B1630/23 is output B
DTC B1630/23 and B1635/24 are not output C



A

2.CHECK CONNECTION OF CONNECTORS

B

8.CHECK CONNECTION OF CONNECTORS

C

2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the side airbag sensor RH and the rear airbag sensor RH.


OK:

The connectors are properly connected.



OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS
a.

Disconnect the connectors from the side airbag sensor RH and rear airbag sensor RH.


b.

Check that the connectors (on the side airbag sensor RH side and the rear airbag sensor RH side) are not damaged (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).


OK:

The connectors are not deformed or damaged.



OK

4.CHECK REAR AIRBAG SENSOR RH CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR

4.CHECK REAR AIRBAG SENSOR RH CIRCUIT
U153687E02
3.479,1.75 3.052,2.063 false 3.542,1.75 4.063,2.104 false 3.604,2.031 4.01,2.323 false 5.688,1.792 5.125,2.188 true 5.76,1.792 6.167,2.229 true 0.125,1.531 1.063,1.885 0.938,0.354 10 false Rear Airbag Sensor RH 1.552,1.531 2.354,1.885 0.802,0.354 10 false Side Airbag Sensor RH 1.75,1.083 1.875,1.25 0.125,0.167 10 false A 0.594,1.052 0.719,1.219 0.125,0.167 10 false F 1.427,1.292 1.552,1.458 0.125,0.167 10 false B 1.25,1.292 1.375,1.458 0.125,0.167 10 false C 1.135,1.292 1.26,1.458 0.125,0.167 10 false D 0.938,1.292 1.063,1.458 0.125,0.167 10 false E 4.844,1.396 5.104,1.563 0.26,0.167 10 false L10 2.74,1.406 2.99,1.573 0.25,0.167 10 false P3 2.375,0.365 4.698,0.719 2.323,0.354 10 false Rear view of wire harness connector: (to Rear Airbag Sensor RH) 4.833,0.365 7.156,0.719 2.323,0.354 10 false Rear view of wire harness connector: (to Side Airbag Sensor RH) 4.052,1.656 4.865,1.844 0.813,0.188 10 false Connector E 6.125,1.656 6.938,1.844 0.813,0.188 10 false Connector B 4.094,2.083 4.51,2.271 0.417,0.188 10 false BCR- 4.948,2.219 5.323,2.406 0.375,0.188 10 false BCR- 2.688,2.052 3.104,2.219 0.417,0.167 10 false BCR+ 6.104,2.25 6.521,2.417 0.417,0.167 10 false BCR+ 4.01,2.333 4.844,2.49 0.833,0.156 10 false Service Wire

a.

Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L10-1 (BCR+) - Body ground Ignition switch ON Below 1 V
L10-2 (BCR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Disconnect the connectors from the side airbag sensor RH and rear airbag sensor RH.


g.

Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector E.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L10-1 (BCR+) - L10-2 (BCR-) Always Below 1 Ω



i.

Disconnect the service wire from the connector E.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L10-1 (BCR+) - L10-2 (BCR-) Always 1 MΩ or higher
L10-1 (BCR+) - Body ground Always 1 MΩ or higher
L10-2 (BCR-) - Body ground Always 1 MΩ or higher




OK

5.CHECK REAR AIRBAG SENSOR RH

NG

7.CHECK FRONT DOOR WIRE RH (SIDE AIRBAG SENSOR RH - NO. 2 FLOOR WIRE)
5.CHECK REAR AIRBAG SENSOR RH
a.
C148441E20
0.677,1.302 1.469,1.958 0.792,0.656 10 false Rear Airbag Sensor LH 1.906,1.281 2.698,1.938 0.792,0.656 10 false Side Airbag Sensor RH

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Interchange the rear airbag sensor RH with LH and connect the connectors to them.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

g.

Turn the ignition switch off.


h.

Turn the ignition switch to ON, and wait for at least 60 seconds.


i.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1635/24 is output A
DTC B1630/23 is output B
DTC B1630/23 and B1635/24 are not output C

HINT:

Codes other than DTC B1630/23 and B1635/24 may be output at this time, but they are not related to this check.



j.

Turn the ignition switch off.


k.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


l.

Return the rear airbag sensor RH and LH to their original positions and connect the connectors to them.



A

6.CHECK SIDE AIRBAG SENSOR RH

B

C

6.CHECK SIDE AIRBAG SENSOR RH
a.
C171827E13
0.578,1.435 1.334,1.750 0.755,0.316 10 Side Airbag Sensor LH 2.11,1.226 3.013,1.370 0.903,0.144 10 Airbag Sensor

Interchange the side airbag sensor RH with LH and connect the connectors to them.


b.

Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result Proceed to
DTC B1635/24 is output A
DTC B1630/23 is output B
DTC B1630/23 and B1635/24 are not output C


h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


j.

Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



A

B

C

7.CHECK FRONT DOOR WIRE RH (SIDE AIRBAG SENSOR RH - NO. 2 FLOOR WIRE)
U153689E02
3.125,1.927 2.823,2.26 true 3.292,1.927 3.615,2.24 true 3.26,2.219 3.51,2.479 false 5.688,1.771 5.125,2.125 true 5.771,1.781 6.188,2.208 true 0.979,1.083 0.979,0.125 0.979,0.125 0.865,0.125 false 1.417,1.083 1.417,0.104 1.417,0.104 1.479,0.104 false 0.115,0.063 0.823,0.375 0.708,0.313 10 false No. 2 Floor Wire 1.521,0.052 2.281,0.375 0.76,0.323 10 false Front Door Wire RH 0.063,1.542 1.042,1.906 0.979,0.365 10 false Rear Airbag Sensor RH 1.635,1.552 2.594,1.906 0.958,0.354 10 false Side Airbag Sensor RH 1.802,1.063 1.938,1.229 0.135,0.167 10 false A 0.5,1.052 0.635,1.219 0.135,0.167 10 false F 1.542,1.25 1.677,1.417 0.135,0.167 10 false B 1.229,1.25 1.365,1.417 0.135,0.167 10 false C 1.094,1.24 1.229,1.406 0.135,0.167 10 false D 0.792,1.24 0.927,1.406 0.135,0.167 10 false E 2.521,1.281 2.813,1.458 0.292,0.177 10 false LP1 2.385,0.24 4.813,0.583 2.427,0.344 10 false Front view of wire harness connector: (to No. 2 Floor Wire) 4.813,0.24 7.146,0.583 2.333,0.344 10 false Rear view of wire harness connector: (to Side Airbag Sensor RH) 3.656,1.625 4.583,1.813 0.927,0.188 10 false Connector C 4.948,1.271 5.219,1.448 0.271,0.177 10 false L10 6.104,1.625 7,1.813 0.896,0.188 10 false Connector B 3.656,2.198 4.073,2.354 0.417,0.156 10 false BCR+ 4.813,2.125 5.229,2.281 0.417,0.156 10 false BCR- 2.396,2.198 2.813,2.354 0.417,0.156 10 false BCR- 6.177,2.198 6.594,2.354 0.417,0.156 10 false BCR+ 3.479,2.5 4.323,2.677 0.844,0.177 10 false Service Wire

a.

Disconnect the No. 2 floor wire connector from the door wire RH.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L10-1 (BCR+) - Body ground Ignition switch ON Below 1 V
L10-2 (BCR-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L10-1 (BCR+) - L10-2 (BCR-) Always Below 1 Ω



i.

Disconnect the service wire from connector C.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L10-1 (BCR+) - L10-2 (BCR-) Always 1 MΩ or higher
L10-1 (BCR+) - Body ground Always 1 MΩ or higher
L10-2 (BCR-) - Body ground Always 1 MΩ or higher




OK

REPLACE NO. 2 FLOOR WIRE

NG

REPLACE FRONT DOOR WIRE RH

8.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the side airbag sensor LH and the rear airbag sensor LH.


OK:

The connectors are properly connected.



OK

9.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

9.CHECK CONNECTORS
a.

Disconnect the connectors from the side airbag sensor LH and rear airbag sensor LH.


b.

Check that the connectors (on the side airbag sensor LH side and the rear airbag sensor LH side) are not damaged (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).


OK:

The connectors are not deformed or damaged.



OK

10.CHECK REAR AIRBAG SENSOR LH CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR

10.CHECK REAR AIRBAG SENSOR LH CIRCUIT
U153688E02
3.469,1.74 3.042,2.052 true 3.531,1.75 4.052,2.104 true 3.604,2.031 4.01,2.323 false 5.688,1.792 5.125,2.188 true 5.74,1.781 6.146,2.219 true 0.125,1.531 1.063,1.885 0.938,0.354 10 false Rear Airbag Sensor LH 1.552,1.531 2.354,1.885 0.802,0.354 10 false Side Airbag Sensor LH 1.75,1.083 1.875,1.25 0.125,0.167 10 false A 0.594,1.052 0.719,1.219 0.125,0.167 10 false F 1.427,1.292 1.552,1.458 0.125,0.167 10 false B 1.25,1.292 1.375,1.458 0.125,0.167 10 false C 1.135,1.292 1.26,1.458 0.125,0.167 10 false D 0.938,1.292 1.063,1.458 0.125,0.167 10 false E 4.833,1.406 5.135,1.573 0.302,0.167 10 false M12 2.719,1.396 2.969,1.563 0.25,0.167 10 false O3 2.375,0.365 4.698,0.719 2.323,0.354 10 false Rear view of wire harness connector: (to Rear Airbag Sensor LH) 4.833,0.365 7.156,0.719 2.323,0.354 10 false Rear view of wire harness connector: (to Side Airbag Sensor LH) 4.052,1.656 4.865,1.844 0.813,0.188 10 false Connector E 6.125,1.656 6.938,1.844 0.813,0.188 10 false Connector B 4.094,2.083 4.51,2.271 0.417,0.188 10 false BCL+ 4.948,2.219 5.323,2.406 0.375,0.188 10 false BCL- 2.688,2.052 3.104,2.219 0.417,0.167 10 false BCL- 6.104,2.25 6.521,2.417 0.417,0.167 10 false BCL+ 4.01,2.333 4.844,2.49 0.833,0.156 10 false Service Wire

a.

Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M12-1 (BCL+) - Body ground Ignition switch ON Below 1 V
M12-2 (BCL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Disconnect the connectors from the side airbag sensor LH and rear airbag sensor LH.


g.

Using a service wire, connect terminals 1 (BCL+) and 2 (BCL-) of connector E.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M12-1 (BCL+) - M12-2 (BCL-) Always Below 1 Ω



i.

Disconnect the service wire from the connector E.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M12-1 (BCL+) - M12-2 (BCL-) Always 1 MΩ or higher
M12-1 (BCL+) - Body ground Always 1 MΩ or higher
M12-2 (BCL-) - Body ground Always 1 MΩ or higher




OK

11.CHECK REAR AIRBAG SENSOR LH

NG

13.CHECK FRONT DOOR WIRE LH (SIDE AIRBAG SENSOR LH - FLOOR WIRE)
11.CHECK REAR AIRBAG SENSOR LH
C148441E21
0.656,1.292 1.458,1.844 0.802,0.552 10 false Rear Airbag Sensor RH 1.865,1.271 2.667,1.823 0.802,0.552 10 false Side Airbag Sensor LH

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Interchange the rear airbag sensor LH with RH and connect the connectors to them.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

g.

Turn the ignition switch off.


h.

Turn the ignition switch to ON, and wait for at least 60 seconds.


i.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1630/23 is output A
DTC B1635/24 is output B
DTC B1630/23 and B1635/24 are not output C

HINT:

Codes other than DTC B1630/23 and B1635/24 may be output at this time, but they are not related to this check.



j.

Turn the ignition switch off.


k.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


l.

Return the rear airbag sensor LH and RH to their original positions and connect the connectors to them.



A

12.CHECK SIDE AIRBAG SENSOR LH

B

C

12.CHECK SIDE AIRBAG SENSOR LH
a.
C180158E01
0.597,1.157 1.369,1.486 0.772,0.330 10 Side Airbag Sensor RH 2.102,1.225 3.000,1.555 0.898,0.330 10 Center Airbag Sensor

Interchange the side airbag sensor LH with RH and connect the connectors to them.


b.

Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result Proceed to
DTC B1630/23 is output A
DTC B1635/24 is output B
DTC B1630/23 and B1635/24 are not output C


h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


j.

Return the side airbag sensor LH and RH to their original positions and connect the connectors to them.



A

B

C

13.CHECK FRONT DOOR WIRE LH (SIDE AIRBAG SENSOR LH - FLOOR WIRE)
U153690E02
3.125,1.927 2.823,2.26 false 3.302,1.927 3.625,2.24 false 3.26,2.219 3.51,2.479 false 5.688,1.771 5.125,2.125 false 5.76,1.781 6.177,2.208 false 0.979,1.073 0.979,0.115 0.979,0.115 0.865,0.115 false 1.417,1.073 1.417,0.094 1.417,0.094 1.479,0.094 false 0.188,0.052 0.865,0.365 0.677,0.313 10 false Floor Wire 1.521,0.042 2.281,0.365 0.76,0.323 10 false Front Door Wire LH 0.063,1.542 1.042,1.906 0.979,0.365 10 false Rear Airbag Sensor LH 1.635,1.552 2.594,1.906 0.958,0.354 10 false Side Airbag Sensor LH 1.802,1.063 1.938,1.229 0.135,0.167 10 false A 0.5,1.052 0.635,1.219 0.135,0.167 10 false F 1.542,1.25 1.677,1.417 0.135,0.167 10 false B 1.229,1.25 1.365,1.417 0.135,0.167 10 false C 1.094,1.24 1.229,1.406 0.135,0.167 10 false D 0.792,1.24 0.927,1.406 0.135,0.167 10 false E 2.51,1.281 2.833,1.458 0.323,0.177 10 false MO1 2.385,0.24 4.813,0.583 2.427,0.344 10 false Front view of wire harness connector: (to Floor Wire) 4.813,0.24 7.146,0.583 2.333,0.344 10 false Rear view of wire harness connector: (to Side Airbag Sensor LH) 3.656,1.625 4.583,1.813 0.927,0.188 10 false Connector C 4.875,1.281 5.208,1.458 0.333,0.177 10 false M12 6.104,1.625 7,1.813 0.896,0.188 10 false Connector B 3.656,2.198 4.073,2.354 0.417,0.156 10 false BCL+ 4.813,2.125 5.229,2.281 0.417,0.156 10 false BCL- 2.396,2.198 2.813,2.354 0.417,0.156 10 false BCL- 6.177,2.198 6.594,2.354 0.417,0.156 10 false BCL+ 3.479,2.5 4.323,2.677 0.844,0.177 10 false Service Wire

a.

Disconnect the floor wire connector from the door wire LH.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M12-1 (BCL+) - Body ground Ignition switch ON Below 1 V
M12-2 (BCL-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M12-1 (BCL+) - M12-2 (BCL-) Always Below 1 Ω



i.

Disconnect the service wire from connector C.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M12-1 (BCL+) - M12-2 (BCL-) Always 1 MΩ or higher
M12-1 (BCL+) - Body ground Always 1 MΩ or higher
M12-2 (BCL-) - Body ground Always 1 MΩ or higher




OK

REPLACE FLOOR WIRE

NG

REPLACE FRONT DOOR WIRE LH