Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27L0U _58 Vehicle Interior _049341 SUPPLEMENTAL RESTRAINT SYSTEMS _0235848 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1655/37  Driver Side Seat Belt Buckle Switch Circuit Malfunction  


DESCRIPTION

The seat belt buckle switch LH circuit consists of the center airbag sensor and the front seat inner belt LH.

DTC B1655/37 is stored when a malfunction is detected in the seat belt buckle switch LH circuit.

DTC Code Detection Condition Trouble Area
B1655/37 When one of following conditions is met:
·

The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat belt buckle switch LH circuit for 2 seconds.

·

Front seat inner belt LH malfunction

·

Center airbag sensor malfunction


·

Floor wire

·

Front seat inner belt assembly LH (Seat belt buckle switch LH)

·

Center airbag sensor assembly



WIRING DIAGRAM

C158843E03
2.46,1.452 2.713,1.678 0.253,0.225 10 1 2.461,3.037 2.582,3.206 0.121,0.170 10 3 1.983,1.201 2.403,1.357 0.420,0.156 10 LBE+ 2.024,2.773 2.423,2.921 0.399,0.149 10 LBE- 5.863,1.369 6.269,1.539 0.406,0.170 10 DBE+ 5.579,1.442 5.825,1.611 0.246,0.170 10 11 0.494,3.926 0.845,4.068 0.350,0.142 10 O4 0.497,4.081 2.063,4.230 1.566,0.149 10 Front Seat Inner Belt LH 5.574,3.923 5.922,4.079 0.348,0.156 10 O1 5.574,4.077 6.950,4.254 1.377,0.177 10 Center Airbag Sensor 5.59,3.02 5.836,3.190 0.246,0.170 10 12 5.861,2.924 6.267,3.094 0.406,0.170 10 DBE-

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and front seat inner belt LH.

OK:

The connectors are properly connected.




OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and the front seat inner belt LH.


b.

Check that the connectors (on the center airbag sensor side and front seat inner belt LH side) are not damaged (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

OK:

The connectors are not deformed or damaged.




OK

3.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT LH)

NG

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT LH)
U153566E01
0.281,0.523 0.960,0.670 0.679,0.147 10 Floor Wire 0.536,1.093 0.674,1.277 0.139,0.184 10 D 0.884,1.297 1.095,1.499 0.211,0.202 10 C 1.211,1.297 1.441,1.508 0.230,0.211 10 B 1.537,1.092 1.776,1.294 0.239,0.202 10 A 1.38,1.587 2.296,1.902 0.915,0.315 10 Center Airbag Sensor 0.149,1.514 1.036,1.836 0.887,0.323 10 Front Seat Inner Belt LH 2.336,0.146 4.753,0.506 2.416,0.361 10 Front view of wire harness connector: (to Front Seat Inner Belt LH) 4.828,0.152 7.147,0.512 2.319,0.361 10 Rear view of wire harness connector: (to Center Airbag Sensor) 2.808,1.182 3.085,1.375 0.276,0.193 10 O4 5.001,1.265 5.300,1.430 0.299,0.165 10 O1 2.581,1.454 2.987,1.628 0.406,0.174 10 LBE+ 2.581,2.07 2.940,2.244 0.360,0.174 10 LBE- 3.387,1.738 2.942,1.563 false 3.387,1.893 2.942,2.071 false 3.833,1.338 4.706,1.480 0.873,0.142 10 Connector C 6.108,1.331 6.917,1.487 0.809,0.156 10 Connector B 1.096,1.12 1.096,0.61 1.096,0.61 0.972,0.61 false 5.881,1.941 6.138,2.122 false 5.769,1.939 5.393,2.122 false 6.017,2.13 6.416,2.284 0.399,0.154 10 DBE+ 5.074,2.13 5.447,2.291 0.373,0.161 10 DBE- 5.713,2.447 6.534,2.596 0.820,0.149 10 Service Wire 5.781,2.188 5.842,2.447 false

a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O4-1 (LBE+) - Body ground Ignition switch ON Below 1 V
O4-3 (LBE-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 11 (DBE+) and 12 (DBE-) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O4-1 (LBE+) - O4-3 (LBE-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O4-1 (LBE+) - O4-3 (LBE-) Always 1 MΩ or higher
O4-1(LBE+) - Body ground Always 1 MΩ or higher
O4-3 (LBE-) - Body ground Always 1 MΩ or higher




OK

4.CHECK FRONT SEAT INNER BELT LH

NG

REPLACE FLOOR WIRE

4.CHECK FRONT SEAT INNER BELT LH
a.
C158841E07
0.526,0.995 1.467,1.366 0.941,0.371 10 Front Seat Inner Belt LH 1.785,1.08 2.726,1.430 0.941,0.350 10 Center Airbag Sensor

Connect the connector to the center airbag sensor and the front seat inner belt LH.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1655/37 is not output.


HINT:

Codes other than DTC B1655/37 may be output at this time, but they are not related to this check.




OK

NG

5.REPLACE FRONT SEAT INNER BELT LH
5.REPLACE FRONT SEAT INNER BELT LH
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the front seat inner belt LH (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).

HINT:

Perform inspection using parts from a normal vehicle if possible.




NEXT

6.CHECK CENTER AIRBAG SENSOR
6.CHECK CENTER AIRBAG SENSOR
a.
C158841E07
0.526,0.995 1.467,1.366 0.941,0.371 10 Front Seat Inner Belt LH 1.785,1.08 2.726,1.430 0.941,0.350 10 Center Airbag Sensor

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.



d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1655/37 is not output.


HINT:

Codes other than DTC B1655/37 may be output at this time, but they are not related to this check.




OK

END

NG