Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SEAT POSITION SENSOR
RM27L0U _58 Vehicle Interior _049341 SUPPLEMENTAL RESTRAINT SYSTEMS _0235854 SEAT POSITION SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  SEAT POSITION SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.


HINT:

The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.


PROCEDURE

Hide 89178A 1.INSTALL SEAT POSITION AIRBAG SENSOR (for Manual Seat)

a.

Check that the ignition switch is turned off.


b.

Check that the battery negative (-) terminal is disconnected.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
U150897E02
1.823,1.385 2.208,1.896 false 0.958,1.271 0.833,1.271 false 0.958,1.354 0.833,1.354 false 0.865,1.271 0.865,1.354 false 0.865,1.188 0.865,1.25 false 0.865,1.375 0.865,1.438 false 1.01,1.667 1.25,1.469 false 1.729,0.573 1.958,0.875 false 0.385,0.458 1.771,0.635 1.385,0.177 10 false Seat Position Sensor 1.833,1.875 2.719,2.052 0.885,0.177 10 false Feeler Gauge 0.406,1.229 0.771,1.417 0.365,0.188 10 false 1 mm 0.635,1.677 1.24,1.823 0.604,0.146 10 false Seat Rail

Using an 1 mm (0.039 in.) feeler gauge, install the seat position airbag sensor.

NOTICE:
·

If the seat position airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace the seat position airbag sensor with a new one.

·

When installing the seat position airbag sensor, make sure that the SRS wiring does not interfere with other parts and is not pinched between other parts.



HINT:

Maintain a clearance between the seat position airbag sensor and the seat rail of between 0.6 mm (0.023 in.) and 2 mm (0.079 in.).



d.
B443276

Using "TORX" socket wrench, tighten the "TORX" screw to install the seat position airbag sensor.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Make sure that the clearance between the seat position airbag sensor and the seat rail is between 0.6 mm (0.023 in.) and 2 mm (0.079 in.).


f.

Connect the connector to the seat position airbag sensor.


g.

Check that there is no looseness in the installation parts of the seat position airbag sensor.


h.

Engage the pin and install a new seat position sensor protector.


Hide 89178A 2.INSTALL SEAT POSITION AIRBAG SENSOR (for Power Seat)

a.

Check that the ignition switch is turned off.


b.

Check that the battery negative (-) terminal is disconnected.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
U150897E02
1.823,1.385 2.208,1.896 false 0.958,1.271 0.833,1.271 false 0.958,1.354 0.833,1.354 false 0.865,1.271 0.865,1.354 false 0.865,1.188 0.865,1.25 false 0.865,1.375 0.865,1.438 false 1.01,1.667 1.25,1.469 false 1.729,0.573 1.958,0.875 false 0.385,0.458 1.771,0.635 1.385,0.177 10 false Seat Position Sensor 1.833,1.875 2.719,2.052 0.885,0.177 10 false Feeler Gauge 0.406,1.229 0.771,1.417 0.365,0.188 10 false 1 mm 0.635,1.677 1.24,1.823 0.604,0.146 10 false Seat Rail

Using an 1 mm (0.039 in.) feeler gauge, install the seat position airbag sensor.

NOTICE:
·

If the seat position airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace the seat position airbag sensor with a new one.

·

When installing the seat position airbag sensor, make sure that the SRS wiring does not interfere with other parts and is not pinched between other parts.



HINT:

Maintain a clearance between the seat position airbag sensor and the seat rail of between 0.6 mm (0.023 in.) and 2 mm (0.079 in.).



d.
B443277

Using "TORX" socket wrench, tighten the "TORX" screw to install the seat position airbag sensor.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Make sure that the clearance between the seat position airbag sensor and the seat rail is between 0.6 mm (0.023 in.) and 2 mm (0.079 in.).


f.

Connect the connector to the seat position airbag sensor.


g.

Check that there is no looseness in the installation parts of the seat position airbag sensor.


h.

Engage the pin and install a new seat position sensor protector.


Hide 71812D 3.INSTALL FRONT SEAT CUSHION SHIELD (for Manual Seat)

Hide 4.INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat)

a.

Hide 71200S 5.INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat)

a.

Hide 6.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Torque:
5.4 N*m (54 kgf*cm, 48 in.*lbf)