Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).
Use the same procedure for both the RH and LH sides.
The procedure described below is for the RH side.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
67673A
3.REMOVE REAR DOOR FRAME GARNISH
Disengage the 6 clips and remove the rear door frame garnish.
74271A
4.REMOVE REAR DOOR ARMREST BASE UPPER PANEL
Disengage the 2 clips and 5 claws and remove the rear door armrest base upper panel.
69283A
5.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG
Using a moulding remover, disengage the 4 claws and remove the rear door inside handle bezel plug.
67603
6.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY
Remove the rear door armrest cover.
Remove the 2 screws.
Disengage the 9 clips.
Disconnect the connector.
Disconnect the rear door lock remote control cable and the rear door inside locking cable and remove the rear door trim board sub-assembly.
69277
7.REMOVE REAR DOOR INSIDE HANDLE BEZEL
Remove the 4 screws and remove the rear door inside handle bezel.
69205A
8.REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY
Remove the 3 screws and remove the rear door inside handle sub-assembly.
68173B
9.REMOVE REAR DOOR GLASS INNER WEATHERSTRIP
Raise the 8 claws of the rear door glass inner weatherstrip and then remove the rear door glass inner weatherstrip from the rear door trim board sub-assembly, as shown in the illustration.
86160Y
10.REMOVE REAR NO. 1 SPEAKER ASSEMBLY
67626C
11.REMOVE REAR DOOR TRIM NO. 2 BRACKET
Remove the 2 screws and remove the rear door trim No. 2 bracket.
67841E
12.REMOVE REAR DOOR SERVICE HOLE COVER
Disengage the clamps and disconnect the connectors.
Remove the rear door service hole cover.
Remove any tape remaining on the door.
75765A
13.REMOVE REAR DOOR WINDOW FRAME REAR MOULDING
68163H
14.REMOVE REAR DOOR GLASS OUTER WEATHERSTRIP
68152C
15.REMOVE REAR DOOR GLASS RUN
Remove the rear door glass run.
67497
16.REMOVE REAR DOOR FRAME BRACKET
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 rear door frame bracket.
67407F
17.REMOVE REAR DOOR WINDOW FRAME REAR LOWER SUB-ASSEMBLY
Loosen nut A.
Remove the 3 bolts and remove the rear door window frame rear lower sub-assembly.
Do not drop or damage the rear door window frame rear lower sub-assembly.
67405B
18.REMOVE REAR DOOR WINDOW GUIDE FRONT SUB-ASSEMBLY
Remove the 2 bolts and remove rear door window guide front sub-assembly.
Do not drop or damage the rear door window guide front sub-assembly when removing the bolts.
68103
19.REMOVE REAR DOOR GLASS SUB-ASSEMBLY
Provisionally install the power window switch.
Move the rear door glass until the 2 bolts can be seen through the service holes.
Remove the 2 bolts and remove the rear door glass sub-assembly.
Do not damage the door glass.
69803
20.REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY
Disconnect the connector.
Loosen bolt A.
Remove the 5 bolts and remove the rear door window regulator sub-assembly.
Do not damage the rear door window regulator sub-assembly.
68630D
21.REMOVE REAR DOOR CHECK ASSEMBLY
Remove the bolt and 2 nuts.
Remove the rear door check assembly.
Do not drop or damage the rear door check assembly when removing the bolt and nuts.
67871
22.REMOVE REAR DOOR WEATHERSTRIP
Disengage the 42 clips and remove the rear door weatherstrip.
67887A
23.REMOVE REAR DOOR NO. 2 WEATHERSTRIP
Disengage the 17 clips and remove rear door No. 2 weatherstrip.
69050A
24.REMOVE REAR DOOR LOCK
69227J
25.REMOVE REAR DOOR OUTSIDE HANDLE COVER
Using "TORX" socket wrench T30, remove the screw and the rear door outside handle cover.
69230
26.REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY
Remove the rear door outside handle assembly by sliding and pulling it in the direction indicated by the arrow mark in the illustration.
69242G
27.REMOVE REAR DOOR OUTSIDE HANDLE REAR PAD
Disengage the 2 claws and remove the rear door outside handle rear pad.
69241G
28.REMOVE REAR DOOR OUTSIDE HANDLE FRONT PAD
Disengage the 2 claws and remove the rear door outside handle front pad.
69203A
29.REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
Using "TORX" socket wrench T30, loosen the screw.
Disengage the claw and slide the rear door outside handle frame sub-assembly to remove it.
30.REMOVE CUSHION
Remove the cushions from the door panel.