Home › DRIVE LINE › DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY

REAR DIFFERENTIAL CARRIER ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL NO. 1 REAR DIFFERENTIAL SUPPORT


    C097682
  1. Install the No. 1 rear differential support to the rear differential carrier assembly with the 2 bolts and 2 nuts.

    Torque:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }

    HINT:
    Hold the bolt and tighten the nut.



2. INSTALL REAR DIFFERENTIAL DYNAMIC DAMPER


    D030576
  1. Install the rear differential dynamic damper to the No. 1 rear differential support with the 2 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



3. INSTALL REAR DIFFERENTIAL SUPPORT ASSEMBLY


    D030577
  1. Install the rear differential support assembly to rear differential carrier assembly with the 3 bolts.

    Torque:
    100 N*m{ 1,020 kgf*cm , 74 ft.*lbf }



4. INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY


    D030575
  1. Jack up the rear differential carrier assembly.

  1. Install the rear differential carrier assembly with the 2 bolts.

    Torque:
    106 N*m{ 1,081 kgf*cm , 78 ft.*lbf }



    D030574
  1. Connect the No. 1 rear differential support with the bolt and nut.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }

    HINT:
    Tighten the bolt.



5. INSTALL REAR DRIVE SHAFT ASSEMBLY LH

HINT:
Install procedure of RH side is the same as that of LH side. (Click here)



6. INSTALL REAR AXLE SHAFT NUT LH

HINT:
Install procedure of RH side is the same as that of LH side. (Click here)



7. INSTALL REAR SPEED SENSOR LH

HINT:
Install procedure of RH side is the same as that of LH side. (Click here)



8. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY


    C092265E01
  1. Align the matchmarks on the propeller shaft assembly rear flange and differential companion flange, and connect the shaft with the 4 bolts, washers and nuts.



    G024034E01
  1. Remove SST(s) from the extension housing.

  1. Insert the yoke into the extension housing.

    NOTICE:
    1. Be careful not to damage the oil seal.
    2. Be careful not to damage the universal joint boot when installing the propeller shaft.



    C083005
  1. Install the 2 adjusting shims and propeller shaft w/ center bearing, and loosely tighten the 4 bolts.



    C092265
  1. Tighten the 4 nuts.

    Torque:
    74 N*m{ 750 kgf*cm , 54 ft.*lbf }



9. FULLY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY


    F040503E01
  1. Remove the cloth from the joint.

  1. Using a hexagon wrench (6 mm), tighten the 6 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



    F040527E03
  1. With the vehicle unloaded, adjust the dimension between the rear side of the cover and shaft, as shown in the illustration.



    F040528E01
  1. Adjust the front and rear dimensions between the edge surface of the center support bearing and the edge surface of the cushion to 12.5 +- 1.0 mm (0.492 +- 0.039 in.) respectively as shown in the illustration, then torque the bolts.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. Check that the center line of the bracket is at right angles to the shaft axial direction.



  1. If any vibration or noise occurs, perform joint angle check as follows and replace the adjusting shim with a proper one.

    1. Turn the propeller shaft several times by hand to stabilize the center support bearings.

    2. Using a jack, raise and lower the differential to stabilize the differential mounting cushion.

    3. Remove the transfer dynamic damper.

    4. Using SST(s), measure the installation angle of the transfer extension housing (A) and front propeller shaft (B).

      SST
      09370-50010  

      No. 1 joint angle:
      A minus B = -0.4° to -1.6°



    5. Using SST(s), measure the installation angle of the rear propeller shaft (C) and rear differential (D).

      SST
      09370-50010  

      No. 2 joint angle:
      C minus D = -1.6° to -3.6°



      F040924E03

      If the measured angle is not within the specification, adjust with the center support bearing adjusting shim.

      Center support bearing adjusting shim thickness:
      Thickness mm (in.)
      Thickness mm (in.)
      3.2 (0.126)
      4.5 (0.177)
      6.5 (0.256)
      9.0 (0.354)

  1. Install the transfer dynamic damper.

    Torque:
    26 N*m{ 260 kgf*cm , 19 ft.*lbf }



10. INSTALL REAR DIFFERENTIAL DRAIN PLUG
  1. Using a hexagon wrench (10 mm), install the drain plug with a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



11. ADD DIFFERENTIAL OIL
  1. Fill the rear differential carrier assembly with hypoid gear oil.



12. INSPECT DIFFERENTIAL OIL

HINT:
(Click here)



13. INSTALL REAR DIFFERENTIAL FILLER PLUG
  1. Using a hexagon wrench (10 mm), install the filler plug with a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



14. INSTALL REAR WHEEL

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }



15. INSTALL EXHAUST PIPE ASSEMBLY

HINT:
(Click here)



16. INSPECT FOR EXHAUST GAS LEAK

HINT:



17. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

HINT:
(Click here)



18. INSPECT ABS SPEED SENSOR SIGNAL

HINT:
(Click here)