DTC P0171 System Too Lean (Bank 1) |
DTC P0172 System Too Rich (Bank 1) |
DTC P0174 System Too Lean (Bank 2) |
DTC P0175 System Too Rich (Bank 2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0171 P0174 | With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side (2 trip detection logic) |
|
| P0172 P0175 | With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side (2 trip detection logic) |
|

| Related DTCs | P0171: Fuel trim Lean (Bank 1) P0172: Fuel trim Rich (Bank 1) P0174: Fuel trim Lean (Bank 2) P0175: Fuel trim Rich (Bank 2) |
| Required Sensors / Components (Main) | Fuel system |
| Required Sensors / Components (Related) | A/F sensor, Mass air flow meter, Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Duration | Less than 10 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not present | P0010, P0020 (OCV bank 1, 2) P0011, P0021 (VVT system bank 1, 2 - advance) P0012, P0022 (VVT system bank 1, 2 - retard) P0013, P0023 (Exhaust OCV bank 1, 2) P0014, P0024 (Exhaust VVT system bank 1, 2 - advance) P0015, P0025 (Exhaust VVT system bank 1, 2 - retard) P0016, P0018 (VVT system bank 1, 2 - misalignment) P0017, P0019 (Exhaust VVT system bank 1, 2 - misalignment) P0031, P0032, P0051, P0052 (A/F sensor heater) P0100, P0102, P0103 (MAF meter) P0115, P0117, P0118 (ECT sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (TP sensor) P0125 (Insufficient ECT for closed loop) P0335 (CKP sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P0351, P0352, P0353, P0354, P0355, P0356 (Igniter) P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor) P0500 (Vehicle speed sensor) |
| Fuel system status | Closed-loop |
| Battery voltage | 11 V or more |
| Either of the following conditions is met | Condition 1 or 2 |
| 1. Engine RPM | Less than 1100 rpm |
| 2. Intake air amount per revolution | 0.22 g/rev or more |
| Catalyst monitor | Not executed |
| EVAP purge-cut | Executing |
| Either of the following conditions is met | Condition 1 or 2 |
| 1. Average between short-term fuel trim and long-term fuel trim | 35% or more at 80°C (176°F) of ECT |
| 2. Average between short-term fuel trim and long-term fuel trim | -35% or less at 80°C (176°F) of ECT |
| Tester Display (Sensor) | Injection Volumes | Status | Voltages |
| AFS B1S1 or AFS B2S1 (A/F) | +25% | Rich | Less than 3.1 |
| AFS B1S1 or AFS B2S1 (A/F) | -12.5% | Lean | More than 3.5 |
| O2S B1S2 or O2S B2S2 (HO2) | +25% | Rich | More than 0.55 |
| O2S B1S2 or O2S B2S2 (HO2) | -12.5% | Lean | Less than 0.4 |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() | ![]() | - |
| 2 | ![]() | ![]() |
|
| 3 | ![]() | ![]() |
|
| 4 | ![]() | ![]() |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171, P0172, P0174 OR P0175) |
Connect the Techstream to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Trouble Code.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| P0171, P0172, P0174 or P0175 | A |
| P0171, P0172, P0174 or P0175 and other DTCs | B |
|
| ||||
| A | |
| 2.CHECK PCV HOSE CONNECTIONS |
|
| ||||
| OK | |
| 3.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leakage.
|
| ||||
| OK | |
| 4.PERFORM ACTIVE TEST USING TECHSTREAM (A/F CONTROL) |
Connect the Techstream to the DLC3.
Start the engine and turn the tester on.
Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Select the following menu items on the tester: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
Perform the Control the Injection Volume for A/F Sensor operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
Monitor the voltage outputs of the A/F and HO2 sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the tester.
| Tester Display (Sensor) | Injection Volumes | Status | Voltages |
| AFS B1S1 or AFS B2S1 (A/F) | +25% | Rich | Less than 3.1 |
| AFS B1S1 or AFS B2S1 (A/F) | -12.5% | Lean | More than 3.5 |
| O2S B1S2 or O2S B2S2 (HO2) | +25% | Rich | More than 0.55 |
| O2S B1S2 or O2S B2S2 (HO2) | -12.5% | Lean | Less than 0.4 |
| Status AFS B1S1 or AFS B2S1 | Status O2S B1S2 or O2S B2S2 | A/F Condition and A/F Sensor Condition | Misfires | Suspected Trouble Areas | Proceed to |
| Lean/Rich | Lean/Rich | Normal | - | - | C |
| Lean | Lean | Actual air-fuel ratio lean | May occur |
| A |
| Rich | Rich | Actual air-fuel ratio rich | - |
| A |
| Lean | Lean/Rich | A/F sensor malfunction | - | A/F sensor | B |
| Rich | Lean/Rich | A/F sensor malfunction | - | A/F sensor | B |
|
| ||||
|
| ||||
| A | |
| 5.READ VALUE USING TECHSTREAM (COOLANT TEMP) |
Connect the Techstream to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the Coolant Temp twice, when the engine is both cold and warmed up.
|
| ||||
| OK | |
| 6.INSPECT MASS AIR FLOW METER |
Read the values using the Techstream (MAF).
Turn the ignition switch to ON (do not start the engine).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
Wait 30 seconds, and read the values on the Techstream.
|
| ||||
| OK | |
| 7.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 8.INSPECT FOR EXHAUST GAS LEAK |
|
| ||||
| OK | |
| 9.CHECK FOR SPARKS AND IGNITION |
Check for sparks and ignition .
|
| ||||
| OK | |
| 10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME) |
Inspect the fuel injector assembly .
|
| ||||
| OK | |
| 11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the A5 or A6 A/F sensor connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| HT (1) - +B (2) | 1.8 to 3.4 Ω at 20°C (68°F) |
| HT (1) - AF- (4) | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| HT (1) - +B (2) | 1.8 to 3.4 Ω at 20°C (68°F) |
| HT (1) - AF- (4) | 10 kΩ or higher |
Reconnect the A/F sensor connectors.
| Result | Proceed to |
| OK | A |
| NG (for 2WD model) | B |
| NG (for 4WD model) | C |
|
| ||||
|
| ||||
| A | |
| 12.INSPECT RELAY (A/F RELAY) |
![]() |
Remove the A/F relay from the No. 6 engine room R/B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| 3 - 5 | 10 kΩ or higher |
| 3 - 5 | Below 1 Ω (when battery voltage applied to terminals 1 and 2) |
Reinstall the A/F relay.
|
| ||||
| OK | |
| 13.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
![]() |
Disconnect the A5 or A6 A/F sensor connectors.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| +B (A5-2) - Body ground | 9 to 14 V |
| +B (A6-2) - Body ground | 9 to 14 V |
Turn the ignition switch off.
Disconnect the E10 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| HT (A5-1) - HA1A (E10-2) | Below 1 Ω |
| AF+ (A5-3) - A1A+ (E10-22) | Below 1 Ω |
| AF- (A5-4) - A1A- (E10-30) | Below 1 Ω |
| HT (A6-1) - HA2A (E10-1) | Below 1 Ω |
| AF+ (A6-3) - A2A+ (E10-23) | Below 1 Ω |
| AF- (A6-4) - A2A- (E10-31) | Below 1 Ω |
| Tester Connection | Specified Condition |
| HT (A5-1) or HA1A (E10-2) - Body ground | 10 kΩ or higher |
| AF+ (A5-3) or A1A+ (E10-22) - Body ground | 10 kΩ or higher |
| AF- (A5-4) or A1A- (E10-30) - Body ground | 10 kΩ or higher |
| HT (A6-1) or HA2A (E10-1) - Body ground | 10 kΩ or higher |
| AF+ (A6-3) or A2A+ (E10-23) - Body ground | 10 kΩ or higher |
| AF- (A6-4) or A2A- (E10-31) - Body ground | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the A/F sensor connectors.

|
| ||||
| OK | |
| 14.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (for 2WD model (Click here) or 4WD model (Click here)).
| NEXT | |
| 15.PERFORM CONFIRMATION DRIVING PATTERN |
Connect the Techstream to the DLC3 (Procedure A).
Turn the ignition switch to the ON position and turn the tester on (Procedure B).
Clear the DTCs (Click here) (Procedure C).
Select the check mode using the tester (Click here) (Procedure D).
Start the engine and warm it up with all the accessories switched off (Procedure E).
Drive the vehicle at between 38 mph and 75 mph (61 km/h and 120 km/h) and at an engine speed of between 1400 rpm and 3200 rpm for 3 to 5 minutes (Procedure F).

| NEXT | |
| 16.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171, P0172, P0174 OR P0175) |
Select the following menu items: Powertrain / Engine and ECT / Trouble Code.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| No output | A |
| P0171, P0172, P0174 or P0175 | B |
|
| ||||
| A | ||
| ||