Home › Brake › BRAKE (REAR) › REAR BRAKE
RM3650E _54 Brake _079883 BRAKE (REAR) _0387572 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.INSTALL REAR DISC

HINT:
·

Rear discs must only be replaced in pairs (per axle).

·

Fit new rear discs only together with new rear disc brake pads.



a.

Thoroughly clean the contact surface of the rear axle hub sub-assembly, remove traces of corrosion if necessary.

NOTICE:

Irregularities in the contact surface can cause distortion in the rear disc.



b.

Install the rear disc.


c.

Replace the 5 mm hexagon bolt.


d.

Tighten down 5 mm hexagon bolt.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


e.
C413587

Install the rear disc brake cylinder mounting (2).


f.

Replace E16 bolts (1).


g.

Tighten the E16 bolts (1).

Torque:
130 N*m (1326 kgf*cm, 96 ft.*lbf)


Hide 2.INSTALL REAR DISC BRAKE PAD

a.
C413345

Clean the contact surface (1) of the rear disc brake piston with brake cleaner and apply a thin coat of brake pad paste.


b.

Check the cylinder boot for damage and replace if necessary.


c.
C413346

Clean the contact surface of the rear disc brake cylinder assembly with brake cleaner and apply a thin coat of brake pad paste.


d.
C413347

Clean the contact surface (1) of the rear disc brake cylinder mounting with brake cleaner and apply a thin coat of brake pad paste.

NOTICE:

Do not mechanically clean the contact surfaces (1) for the rear disc brake pad support plates at the rear disc brake cylinder mounting to prevent damage to the surface coating.



e.
C413348

Clean the contact surface (1) of the rear disc brake cylinder mounting with brake cleaner and apply a thin coat of brake pad paste.

NOTICE:

Do not mechanically clean the contact surfaces (1) for the rear disc brake pad support plates at the rear disc brake cylinder mounting to prevent damage to the surface coating.



f.

Install the rear disc brake pad support plates.


g.
C413349

Coat the T-head of outer rear disc brake pad in the marked area (1) in each case with a thin coating of brake pad paste.


h.
C413350

Coat the T-head of outer rear disc brake pad in the marked area (1) in each case with a thin coating of brake pad paste.


i.
C413351

Coat the T-head of outer rear disc brake pad in the marked area (1) in each case with a thin coating of brake pad paste.


j.
C413352

Coat the T-head of outer rear disc brake pad in the marked area (1) in each case with a thin coating of brake pad paste.


k.
C413344

Install the rear disc brake pads (1) in the direction of the arrow.


Hide 3.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY

a.
C420442C01
1.563,3.083 1.875,3.281 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length


Using a 14 mm union nut wrench, tighten the rear flexible hose on the rear disc brake cylinder assembly.

Torque:
Specified tightening torque : 22 N*m (224 kgf*cm, 16 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a special tool (fulcrum length of 25.0 mm (0.984 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 19.1 N*m (195 kgf*cm, 14 ft.*lbf)




b.

Insert the rear flexible hose into the holder.

NOTICE:

Make sure that the rear flexible hose does not rest against the components fixed to the body and that it is not twisted.



c.

Install the rear disc brake cylinder assembly.


d.

Replace 15 mm bolts.


e.

Tighten the 15 mm bolts, if applicable, hold against the hexagon head.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 4.INSTALL PAD WEAR INDICATOR WIRE RH (for RH Side)

Hide 6.INSTALL REAR WHEEL

Hide 7. NORMAL CONDITION RECOVERY

a.

Connect the diagnosis system with the vehicle.


b.

Cancel the workshop mode.

Vehicle management / Service functions / Chassis / Parking brake / Workshop mode


c.

Disconnect the diagnosis system from the vehicle.