Home › Suspension › REAR SUSPENSION › TOE CONTROL LINK
RM3650E _53 Suspension _079981 REAR SUSPENSION _0387955 TOE CONTROL LINK A

REAR SUSPENSION  TOE CONTROL LINK  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.

·

Tighten the bolt connection in the normal position.



PROCEDURE

Hide 48706B 1.INSTALL TOE CONTROL LINK SUB-ASSEMBLY

a.

Position the toe control link sub-assembly.


b.
C413572

When installing the toe control link sub-assembly (1), make sure that the tapered side (2) of the rubber mount points in the direction of the rear axle carrier sub-assembly (3).


c.
C413573

Replace the bolt (1).


d.

Hand-tighten the bolt (1).


e.
C413569

Replace the 18 mm nut (1), toe adjust bolt (2) and toe adjust washer (3).


f.

Position the 18 mm nut (1) and toe adjust washer (3).


g.

Hand-tighten the toe adjust bolt (2).


h.
C413573

Tighten down bolt (1).

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


i.

Using SST, tighten the bolt (1) an additional 90°.

SST
09900-WA010  

HINT:
·
C417459C02
2.99,1.271 3.156,1.188 false 2.906,2.094 2.906,1.76 false 0.875,3 1.208,3 false 0.104,0.125 0.417,0.281 0.313,0.156 10 false *a 0.448,0.125 0.76,0.281 0.313,0.156 10 false *b 2.042,0.125 2.354,0.281 0.313,0.156 10 false *c 3.188,1.073 3.427,1.271 0.24,0.198 10 false *d 2.854,2.146 3.167,2.302 0.313,0.156 10 false *b 1.302,2.927 1.615,3.083 0.313,0.156 10 false *c
*a Example
*b Before Tightening
*c After Tightening
*d Magnetic Portion



·

The magnetic portion is used to secure the gauge to the vehicle.

·

After first adjusting the needle of the gauge to 0°, tighten to the specified angle.

·

Perform the work procedure carefully so that the gauge, etc. does not become tilted.




j.
C417119C01
1.771,0.385 2.167,0.25 true 1.229,0.615 1.625,0.417 true 2.281,0.99 2.552,1.188 0.271,0.198 10 true *a 1.063,0.635 1.333,0.833 0.271,0.198 10 true *b
*a Torque Wrench Fulcrum Length
*b 18 mm Union Nut Wrench


Using an 18 mm union nut wrench, tighten the 18 mm nut (1).

Torque:
Specified tightening torque : 108 N*m (1101 kgf*cm, 80 ft.*lbf)

HINT:
·

If necessary, counter support the toe adjust bolt.

·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using an 18 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 400 mm (15.7 in.)):

100 N*m (1020 kgf*cm, 74 ft.*lbf)




Hide 48738 2.INSTALL REAR SUSPENSION ARM COVER

Hide 3.INSTALL REAR WHEEL

Hide 4.INSPECT AND ADJUST REAR WHEEL ALIGNMENT