Home › Suspension › REAR SUSPENSION › REAR LOWER ARM (for No. 2 Arm)
RM3650E _53 Suspension _079981 REAR SUSPENSION _0394032 REAR LOWER ARM(for No. 2 Arm) A

REAR SUSPENSION  REAR LOWER ARM(for No. 2 Arm)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 48740F 1.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY

a.

Replace nut, camber adjust washer and 18 mm camber adjust bolt.


b.

Position the rear No. 2 suspension arm assembly to the rear suspension member sub-assembly.


c.

Position camber adjust washer.


d.

Tighten nut.

Torque:
175 N*m (1785 kgf*cm, 129 ft.*lbf)

HINT:

Tighten the bolt connection in the normal position.



e.
C415925C01
1.76,1.375 2.177,1.594 true 1.021,1.958 1.563,1.823 true 2.24,1.51 2.479,1.729 0.24,0.219 10 true *a 0.74,1.865 0.979,2.083 0.24,0.219 10 true *b
*a Wooden Block
*b Jack


Support the rear axle carrier sub-assembly with the jack and wooden block.


f.
C417113

Lift the rear axle carrier sub-assembly with the jack and wooden block to the point where a new E18 bolt (2) can be inserted.


g.

Replace the nut (3) and E20 bolt (4).


h.

Tighten the nut (3) and E20 bolt (4).

Torque:
165 N*m (1683 kgf*cm, 122 ft.*lbf)


i.

Using SST, tighten the nut (3) an additional 90°.

SST
09900-WA010  

HINT:
·
C417459C02
2.99,1.271 3.156,1.188 false 2.906,2.094 2.906,1.76 false 0.875,3 1.208,3 false 0.104,0.125 0.417,0.281 0.313,0.156 10 false *a 0.448,0.125 0.76,0.281 0.313,0.156 10 false *b 2.042,0.125 2.354,0.281 0.313,0.156 10 false *c 3.188,1.073 3.427,1.271 0.24,0.198 10 false *d 2.854,2.146 3.167,2.302 0.313,0.156 10 false *b 1.302,2.927 1.615,3.083 0.313,0.156 10 false *c
*a Example
*b Before Tightening
*c After Tightening
*d Magnetic Portion



·

The magnetic portion is used to secure the gauge to the vehicle.

·

After first adjusting the needle of the gauge to 0°, tighten to the specified angle.

·

Perform the work procedure carefully so that the gauge, etc. does not become tilted.




j.

Using an 18 mm deep socket wrench, tighten a new 18 mm nut (1).

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


k.

Using SST, tighten the nut (1) an additional 90°.

SST
09900-WA010  

HINT:
·
C417459C02
2.99,1.271 3.156,1.188 false 2.906,2.094 2.906,1.76 false 0.875,3 1.208,3 false 0.104,0.125 0.417,0.281 0.313,0.156 10 false *a 0.448,0.125 0.76,0.281 0.313,0.156 10 false *b 2.042,0.125 2.354,0.281 0.313,0.156 10 false *c 3.188,1.073 3.427,1.271 0.24,0.198 10 false *d 2.854,2.146 3.167,2.302 0.313,0.156 10 false *b 1.302,2.927 1.615,3.083 0.313,0.156 10 false *c
*a Example
*b Before Tightening
*c After Tightening
*d Magnetic Portion



·

The magnetic portion is used to secure the gauge to the vehicle.

·

After first adjusting the needle of the gauge to 0°, tighten to the specified angle.

·

Perform the work procedure carefully so that the gauge, etc. does not become tilted.




l.

for LH Side:

i.

Replace nut.


ii.

Position bracket with the jointed rod.


iii.

Tighten nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)



Hide 2.INSTALL REAR COIL SPRING

Hide 3.INSTALL STONEGUARD

a.
C417127

Install the stoneguard (1) and clip into the latch mechanisms (arrows).

HINT:
·

Observe the marking of the installation location on the stoneguard (1).

·

The arrow on the stoneguard (1) is pointing downwards.




Hide 48738 4.INSTALL REAR SUSPENSION ARM COVER

Hide 5.INSTALL REAR WHEEL

Hide 6.INSPECT AND ADJUST REAR WHEEL ALIGNMENT