DTC B1771 Passenger Side Buckle Switch Circuit Malfunction |
| DTC No. | DTC Detecting Condition | Trouble Area |
| B1771 |
|
|

| 1.CHECK DTC |
Turn the ignition switch to the ON position.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 2.CHECK CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the occupant classification ECU and the front seat inner belt assembly RH.
Disconnect the connectors from the occupant classification ECU and front seat inner belt assembly RH.
Check that the terminals of connectors are not damaged.
|
| ||||
| OK | |
| 3.CHECK NO. 1 SEAT WIRE (TO B+) |
![]() |
Disconnect the connectors from the occupant classification ECU and the front seat inner belt assembly RH.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester connection | Condition | Specified condition |
| O10-13 (BSW) - Body ground | Ignition switch ON | Below 1 V |
| O10-14 (BGND) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | |
| 4.CHECK NO. 1 SEAT WIRE (FOR OPEN) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Using a service wire, connect F24-1 and F24-2 of connector C.
Measure the resistance.
| Tester connection | Condition | Specified condition |
| O10-13 (BSW) - O10-14 (BGND) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK NO. 1 SEAT WIRE (TO GROUND) |
![]() |
Disconnect the service wire from connector C.
Measure the resistance.
| Tester connection | Condition | Specified condition |
| O10-13 (BSW) - Body ground | Always | 1 MΩ or higher |
| O10-14 (BGND) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 6.CHECK NO. 1 SEAT WIRE (FOR SHORT) |
![]() |
Measure the resistance.
| Tester connection | Condition | Specified condition |
| O10-13 (BSW) - O10-14 (BGND) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 7.CHECK DTC |
Connect the connectors to the occupant classification ECU and the front seat inner belt assembly RH.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch to the ON position.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 8.REPLACE BUCKLE SWITCH RH (WITH FRONT SEAT INNER BELT ASSEMBLY RH) |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the front seat inner belt assembly RH (Click here).
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch to the ON position.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 9.REPLACE OCCUPANT CLASSIFICATION ECU |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Store the occupant classification ECU data into the intelligent tester (Click here).
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the occupant classification ECU (Click here).
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch to the ON position.
Load the data from the previous ECU stored in the tester, into the newly installed ECU (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position.
Clear the DTCs stored in the memory (Click here).
| NEXT | |
| 10.PERFORM SENSITIVITY CHECK |
Perform the sensitivity check (Click here).
| NEXT | ||
| ||